Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION AND OPERATION
TM
Direct-Vent
SHORELINE™
DIRECT-VENT GAS FIREPLACE HEATER INSERTS
P/N 850,050M REV. D 03/2010
MODELS
Portland
OTL Report No. 050-F-22-5
US
SHRL 33/40 DV INS
Ce manuel d’installation est disponible en francais, s implement en faire The Shoreline™ fireplace insert is factory equipped for 40,000 BTU
input and can be converted to 33,000 using the smaller orifice provided.
la demande. Numéro de la pièce 850,050CF.
WARNING AVERTISSEMENT
HOT GLASS WILL
UNE SURFACE VITRÉ
Inhaltszusammenfassung zur Seite Nr. 2
CONGRATULATIONS! PACKAGING LIST When you purchased your new gas fireplace insert, you joined To install a Shoreline insert, an insert body, refractory brick panel set the ranks of thousands of individuals whose answer to their home and surround kit are required (each sold separately. See Page 37 for heating needs reflects their concern for aesthetics, efficiency ordering information). and our environment. We extend our continued support to help Fireplace Insert Body Packaging List you achi
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY AND WARNING AVERTISSEMENT INFORMATION On ne devrait pas placer de vêtements ni d’autres matières inflammables sur l’appareil ni à prox- imité. WARNING Young children should be carefully supervised when they are in the same room as the appliance. Tod- WARNING dlers, young children and others may be susceptible Any safety screen or guard removed for servicing to accidental contact burns. A physical barrier is the appliance must be replaced prior to o
Inhaltszusammenfassung zur Seite Nr. 4
These appliances are vented gas appliances. Do not burn wood FOR YOUR SAFETY do not install or operate this appliance without or other material in these appliances. first reading and understanding this manual. Any installation or operation of the appliance deviating from that which is stated This appliance is only for use with the type of gas indicated on in this manual WILL void the warranty and may be hazardous. rating plate. This appliance is not convertible for use with other
Inhaltszusammenfassung zur Seite Nr. 5
This appliance is only for use with the type of gas indicated on the Note: These appliances are designed as supplemental heaters. There- rating plate. This appliance is not convertible for use with other gases, fore, it is advisable to have an alternate heat source when installed in a unless a certified kit is used. dwelling. Cet appareil doit être utilisé uniquement avec les types de gaz indiqués Millivolt Valve & Electrical sur la plaque signalétique. Ne pas l'utiliser avec d'autres gaz sauf
Inhaltszusammenfassung zur Seite Nr. 6
Local, State and National Codes - These appliances must conform with SMOKE DETECTORS all local, state, and national installation codes. In the absence of local and state codes, installation must comply with the current National Fuel Since there are always several potential sources of fire in any home, we Gas Code, ANSI Z223.1, also known as NFPA 54 (In Canada, the current recommend installing smoke detectors. If possible, install the smoke CAN/CSA B149.1 installation code). Electrical wir
Inhaltszusammenfassung zur Seite Nr. 7
NEW YORK CITY, NEW YORK (MEA) COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS (NYC MEA Approval #138-07-E) (Massachusetts Approval #G3-0508-369) These appliances are approved for installation in the US state of Mas- Installation of these appliances are approved for installation in New York sachusetts if the following additional requirements are met: City in the US state of New York. • Install this appliance in accordance with Massachusetts Rules and Regulations 248 C.M.R. • Installation and repair
Inhaltszusammenfassung zur Seite Nr. 8
SPECIFICATIONS: Shoreline™ Note: Due to Lennox’ ongoing commitment to quality , all specifications, ratings and dimensions are subject to change without notice. Insert Dimensions Inches (millimeters) A Left front of unit to center line 13-1/8 (333) B Right front of unit to center line 17-1/4 (438) C Left rear of unit to center line 9 (229) P D Right Rear Of Unit To Center Line 7-5/8 (194) E Center Of Air Intake To Center Line 6-3/4 (172) F Center Of Flue To Center Line 2 (51) G Insert Depth Int
Inhaltszusammenfassung zur Seite Nr. 9
MINIMUM CLEARANCES TO COMBUSTIBLES Mantel - 12” Depth These appliances can be installed in most fireplace configurations. If installed close to an adjacent wall, ensure that the minimum clearances Combustibles Trim or Mantel Depth of 8” or Less to combustible surfaces are maintained. A local building inspector should review your plans prior to installation. F Refer to Figures 2 through 4 for clearances to combustibles. Minimum clearances include any projections such as shelves, window sills
Inhaltszusammenfassung zur Seite Nr. 10
INSTALLATION CAUTIONS • Trim panels or surrounds must not seal ventila- Fireplace Requirements tion openings in the existing fireplace that the appliance is installed in. These heaters are designed to be installed into an existing masonry • The fireplace in which this gas insert is to be fireplace (built to UBC 37 or ULC S628 standards) or factory built solid installed must be thoroughly cleaned if it has fuel, wood burning fireplace (listed to UL 127 or ULC S610) only. All been us
Inhaltszusammenfassung zur Seite Nr. 11
Venting Requirements Positive Flue Connection Masonry and Factory Built Fireplaces Approved Vent Systems: A qualified installer should evaluate the existing fireplace to determine Lennox Hearth Products Co-linear Chimney Liner Kit Recommended: the best method for achieving a positive flue connection between the vent • The Flex Kit, Cat. No. H0909 includes one 35 feet flex liner and four and intake liners and the chimney. gear clamps. • The Termination Kit, Cat. No. TKDVI includes the termina
Inhaltszusammenfassung zur Seite Nr. 12
Vertical Venting The combustion air intake pipe can be connected to the termination cap (see Figure 6b) or it can terminate inside the chimney (see Figure 6a). If combustion air intake pipe is terminated inside the chimney and not connected to the actual termination cap the bottom opening of the chim- ney (chimney throat) must be sealed around the vent pipes. Use a non combustible seal-off plate (i.e. 22 gage sheet steel) or unfaced fiberglass insulation (8 lb per square foot density mini
Inhaltszusammenfassung zur Seite Nr. 13
SHORELINE™ DOOR ASSEMBLY INSTALLATION OR REMOVAL See Detail E INSTRUCTIONS Tools Needed: 5/32” Allen Wrench or T-Handle Cat. No. Description H5746 Shoreline Door Assembly (Figure 9) Shoreline Door Kit - Packaging List Models SHR33 & SHR40 Quantity Description 1 Shoreline Door Assembly Table 6 - (refer to Figure 9) Note: The Shoreline insert comes with the door already on the unit. Just reverse the steps here to remove the door to access the burner area. Upper Latch Tabs Detail E Figure 11
Inhaltszusammenfassung zur Seite Nr. 14
2. Next place the rear panel (B). It will set on the bracket mounted to the SHORELINE™ REFRACTORY BRICK INSTALLATION INSTRUCTIONS blower mounting plate on the back of the firebox. See Figure 16. Tools Needed: No tools are needed Cat. No. Model Description H7987 SHR-BRK-STD Brick Panel Set, Tan H7988 SHR-BRK-RED Brick Panel Set, Red H7989 SHR-BRK-ARCHSTONE Brick Panel Set, Architectural (shown) Refractory Brick Panel Kits - Packaging List B Models SHR33 & SHR40 Quantity Description 1 Front
Inhaltszusammenfassung zur Seite Nr. 15
SHORELINE™ LOG SET INSTALLATION INSTRUCTIONS CAUTIONS Tools Needed: No tools are needed • If logs are not installed according to the log installation instructions, flame impingement Cat. No. Description and improper combustion could occur and result H5747 5-Piece Ceramic Log Set in soot and/or excessive production of carbon Log Set - Packaging List monoxide (CO), a colorless, orderless, toxic Models SHR33 & SHR40 gas. Quantity Description • The size and position of the log set is
Inhaltszusammenfassung zur Seite Nr. 16
2. Separate the glowing embers (F) into quarter size pieces and place 4. Place left log (C) on pin in back. Push log against left side of refractory in front. See Figure 24. along ports on burner pan. DO NOT cover burner secondary holes on burner pan. The pattern for the glowing embers should be similar to what is shown in Figure 22. pin F C Figure 24 5. Locate groove in center log (B), and place the top of the right log (D) in groove with the bottom end of the log resting against the r
Inhaltszusammenfassung zur Seite Nr. 17
SHORELINE™ SURROUND ASSEMBLY INSTALLATION Tools Needed: No tools are needed One of the following surround kits is required (Purchased sepa- rately). Detail A Surround Kits Models SHR33 & SHR40 Part/Cat. # Description Dimensions 75387 Small 3-sided Flange 36-5/8”W x 25-7/8”H 75385 Small 4-sided Flange 36-5/8”W x 29-3/16”H 75388 Large 3-sided Flange 41”W x 28”H 75386 Large 4-sided Flange 41”W x 33-1/2”H Table 9 Detail B Note: Install surround with insert positioned in the fireplace, but a few inc
Inhaltszusammenfassung zur Seite Nr. 18
SURROUND BALL SCREW MOUNT ADJUSTMENT C Tools Needed: 7/16” wrench Adjust Ball Screw Adjustment Procedure: Step 1 Open the surround access door. Inspect the tension or lack of tension while opening the door to determine if it should open easier or tighter. Step 2 With access door open you will see the ball screw and jam nut on the surround backing plate near the top surround piece as seen in picture A. Using a 7/16” wrench, loosen the jam nut on the ball screw as shown in Picture B. Step 3
Inhaltszusammenfassung zur Seite Nr. 19
Tables 10 and 11 show the units' gas pressure requirements for GAS LINE INSTALLATION these appliances. Inlet Gas Supply Pressure We recommend that a qualified individual such as a plumber or gas fitter be used to correctly size and route the gas supply line to the appliance. Installing Fuel # Minimum Maximum Desired a gas supply line from the fuel supply to the appliance involves numerous Natural 5" WC/po. C.E 10.5" WC/po. C.E 7" WC/po. C.E considerations of materials, protection, sizing, l
Inhaltszusammenfassung zur Seite Nr. 20
AVERTISSEMENT Un foyer chaud peut causer de graves brûlures Ne laissez jamais un enfant toucher à la vitre ou à toutes autres parties du foyer INSTALLER INSTRUCTIONS - ATTACHING SAFETY IN OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation. These warning labels are a critical step in informing consumers of safe operation of this appliance. ATTACHING SAFETY IN OPERATION WARN- APPOSITION DES MISES EN GARDE RELATIVES COLOCACIó
