Inhaltszusammenfassung zur Seite Nr. 1
ELECTRIC FIREPLACE HEATER
WITH SINGLE GLASS DOOR
Model 91797
ASSEMBLY AND OPERATING INSTRuCTIONS
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANuAL.
© ®
Copyright 2004 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork con-
tained herein may be reproduced in any shape or form without the express written consent of Harbor Freight
Tools. Diagrams
Inhaltszusammenfassung zur Seite Nr. 2
SPECIFICATIONS ITEM DESCRIPTION Power Requirements 120 VAC, 60 Hz, 15 Amps Heater Settings 750 and 1500 Watts Heater Controls Fan On/Off switch; 2 -2750W On/Off switches; Fire light On/Off switch; Temperature thermo- state knob; Fire light brightness knob; Remote Control Unit Line Cord Two-prong polarized plug; 16 AWG x 2C; UL listed Light Bulbs 2 - 60W candelabra bulbs Overall Dimensions 20-3/8 (L) x 11-1/2 (W) x 22-3/4 (H) inches Weight 39 Lbs. The maximum room size of the heater is 400 squ
Inhaltszusammenfassung zur Seite Nr. 3
Electrical Safety 3. Avoid body contact with grounded surfaces such as pipes, radiators, ranges, and refrigerators. There is an increased risk of electric shock if your body is grounded. 4. Do not expose appliances to rain or wet conditions. Water entering a appliance will increase the risk of electric shock. 5. Grounded products must be plugged into an outlet properly installed and grounded in accordance with all codes and ordinances. Never remove the grounding prong or modify the plug
Inhaltszusammenfassung zur Seite Nr. 4
13. When servicing an appliance, use only identical replacement parts. Follow instructions in the “Inspection, Maintenance, And Cleaning” section of this manual. Use of unauthorized parts or failure to follow maintenance instructions may create a risk of electric shock or injury. SPECIFIC SAFETY RuLES FOR THIS PRODuCT 1. Maintain labels and nameplates on the Fireplace Heater. These carry important information. If unreadable or missing, contact Harbor Freight Tools for a replacement. 2. Av
Inhaltszusammenfassung zur Seite Nr. 5
Grounded Tools: Appliances with Three Prong Plugs 1. Appliances marked with “Grounding Required” have a three wire cord and three prong grounding plug. The plug must be connected to a properly grounded outlet. If the appliance should electrically malfunction or break down, grounding provides a low resistance path to carry electricity away from the user, reducing the risk of electric shock. (See Figure A.) 2. The grounding prong in the plug is connected through the green wire inside the co
Inhaltszusammenfassung zur Seite Nr. 6
5. If you are using one extension cord for more than one appliance, add the nameplate amperes and use the sum to determine the required minimum cord size. (See Table A.) 6. If you are using an extension cord outdoors, make sure it is marked with the suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use. 7. Make sure your extension cord is properly wired and in good electrical condition. Always replace a damaged extension cord or have it repaired by a qualified electri
Inhaltszusammenfassung zur Seite Nr. 7
OPERATING INSTRuCTIONS 1. Place the Fireplace Heater in the desired location for operation. This place must be away from curtains and any other flammable material. If an extension cord is used, it must be of the appropriate size (See page 6.). The electrical outlet must be at least a 15 amp circuit. 2. Press the Fan Switch up to turn it on. (See Figure C below.) 3. Press the 750W Switch to enable medium heat. Press the second 750W Switch to enable maximum heat. 4. Adjust the Temperature Ther
Inhaltszusammenfassung zur Seite Nr. 8
loose screws, misalignment or binding of moving parts, cracked or broken parts, damaged electrical wiring, and any other condition that may affect its safe operation. Do not use damaged equipment. 2. Periodically recheck all nuts, bolts, and screws for tightness. 3. Store in a clean and dry location. 4. Open the Fireplace Heater door and clean the rear mirror when it becomes dirty. Wipe the unit with a clean cloth when it becomes dusty. 5. To replace one or both of the fire light bulbs: •
Inhaltszusammenfassung zur Seite Nr. 9
PARTS LIST Part Description Qty. Part Description Qty. 1 Pin 2 38 Clip 3 2 Ring 2 39 Screw for Glass 3 3 Hinge 2 40 Door Glass 1 4 MDF Housing 1 41 Door Frame 1 5 Window for receiver 1 42 Log 2 6 Switch Box 1 43 Log Bed 1 7 Thermostat 1 44 Door Handle 1 8 Front Board 1 45 Grenade of the Handle 1 9 Press Board for glass 1 46 Motor 2 10 Diffuser 1 47 Bulb Holder 2 11 Right Angle Holder 2 48 Handrail 1 12 Flame Board 1 49 Magnet 2 13 Pot Hook for Ribbon 14 50 Bottom Board for Flame 1 14 Ribbon 7 51
Inhaltszusammenfassung zur Seite Nr. 10
ASSEMBLY DRAWING NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as replacement parts. REV 10d SKU 91797 For technical questions, please call 1-800-444-3353 Page 10
Inhaltszusammenfassung zur Seite Nr. 11
WIRING DIAGRAM PLEASE READ THE FOLLOWING CAREFuLLY THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBU- TOR MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMEN
Inhaltszusammenfassung zur Seite Nr. 12
LIMITED 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of 90 days from the date of purchase. This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repairs or alterations outside our facilities, criminal activity, improper installatio
