Bedienungsanleitung Harbor Freight Tools PACIFIC HYDROSTAR 95267

Inhaltszusammenfassung zur Seite Nr. 1

1 HP DIRTY WATER
SUBMERSIBLE PUMP
95267
ASSEMBLY and OPERATING INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
Distributed exclusively by Harbor Freight Tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
SaVe THiS manua

Inhaltszusammenfassung zur Seite Nr. 2

Specifications Motor 120 V, 60 Hz, 4.7 A (run) Operating Temp. 95 Deg. F. Pump Cord 18 Ft. - 3 Prong Plug Min. Switch Level 3” Discharge Size 1-1/2” Overall Dimensions 6.5” Dia. x 12.375” H Discharge Fittings 1-1/4”, 1-1/2” and 1” Housing Material PP Plastic Delivery Height 28.3 Ft. Pump Weight 13.1 Lbs Flow Rate 3570 GPH Motor Drive Magnetic Drive Horsepower 1HP Max. Particle Size 1” Warning: T

Inhaltszusammenfassung zur Seite Nr. 3

6. Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts. Protective, electrically nonconductive clothes and nonskid footwear are recommended when working. Wear restrictive hair covering to contain long hair. 7. Use eye and ear protection. Always wear ANSI-approved impact safety goggles. Wear an ANSI-approved dust mask or respirator when working around metal, wood, and chemical dusts and mists. 8. Do not overreach. Keep proper footing and balance a

Inhaltszusammenfassung zur Seite Nr. 4

18. Water transfers in cycles. Do not attempt to manipulate the switch to keep pump running continuously. It is meant to shut off intermittently. Doing so will damage the pump. Note: Performance of this pump (if powered by line voltage) may vary depending on variations in local line voltage. Extension cord usage may also affect pump performance. Warning: The warnings, cautions, and instructions discussed in this instruction manual cannot cover all possible conditions and situations that m

Inhaltszusammenfassung zur Seite Nr. 5

Installation (continued) Hose Connection: The Universal Fitting (42), in Figure B, connects to various hose sizes. The hoses should be connected using a step nipple (not included). The 1” and 1-1/4” hoses should also be secured with hose clamps (not included). The largest connection (1-1/2”) will yield the greatest flow. The top of the Universal Fitting may be removed to fit on various size hoses (see Figure B). Use a knife to gently trim any unneeded material. Note: Use a pipe joint

Inhaltszusammenfassung zur Seite Nr. 6

Operation Warning: Do not run the pump dry. It will increase wear to the unit and possibly cause seal damage. Note: This pump has a built-in thermal protector for the motor, which automatically shuts it off to avoid overheating. After it cools, it will cycle back on. Wait for the cycle to continue. Do not try to turn on the pump manually after it has cut off. 1. Plug unit into an outlet fitted with a Ground Fault Circuit Interrupter (GFCI). 2. The pump will automatically turn

Inhaltszusammenfassung zur Seite Nr. 7

Troubleshooting Problem 1: Pump runs but will not deliver any water. Cause: Base (38) clogged. Solution: Remove the Screws (1) from the Base (38) and remove Base (38). Clean out dirt or debris and replace. Cause: When starting, the pump water height falls below the minimum water level. Solution: Submerge pump deeper. Cause: Low line voltage. Solution: Consult with an electrician. Cause: Optional check valve stuck or installed backwards. Solution: Remove and examine check valve. Probl

Inhaltszusammenfassung zur Seite Nr. 8

Parts List Description Float Switch Cable and Plug Under Washer 42 42 Universal Adapter 1 NOTE: Some parts are listed and shown for illustration purposes only, and are not avail- able individually as replacement parts. SKU 95267 Page 8

Inhaltszusammenfassung zur Seite Nr. 9

LIMITED 1 YEAR / 90 DAY WARRANTY Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that for a period of ninety days from date of purchase that the engine/motor, the belts (if so equipped), and the blades (if so equipped) are free of defects in materials and workmanship. Harbor Freight Tools also warrants to the original purchaser, for a period of one year from date of purchase, that all