Inhaltszusammenfassung zur Seite Nr. 1
READ AND SAVE THESE INSTRUCTIONS
®
™
BUCKINGHAM
Model No.
CF715AW00
Ceiling Fan
CF715PW00
Owner's Manual
CF715AB00
CF715WB00
Net Weight: 15.5 Lbs.
CF715S00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warranty wil
Inhaltszusammenfassung zur Seite Nr. 2
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
Inhaltszusammenfassung zur Seite Nr. 3
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Wire Size A.W.G. Tools Needed for Assembly Up to 50 ft. 14 One Phillips head screwdriver One stepladder 50-100 ft. 12 One 1/4” blade screwdriver One wire stripper One 5/16” open end wrench, or pliers Three wire connectors (supplied) ! WARNING MATERIALS Before assembly your ceiling fan, refer to section on Wiring outlet box and box connectors must be of
Inhaltszusammenfassung zur Seite Nr. 4
How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 4. Place the ceiling cover over the downrod, making in the hanger ball until the ball falls freely down the sure that the large opening faces upward (Figure 3). downrod (Figure 1). Remove the pin from the downrod, then remove the hanger ball. Retain the pin and hanger ball for reinstallation in step 5. PIN HANGER PIN BALL HANGER BALL SETSCREW DOWNROD DOWNROD CEILING COVER SETSCREW Figure 3 Figure 1 5. Reins
Inhaltszusammenfassung zur Seite Nr. 5
NOTE: Take care not to scratch fan housing when installing blades. 9. Loosely attach one blade assembly to the motor hub using two 1/4-20 x 1/2” Phillips oval head flange screws (Figure 5). Make sure the screws are NOT tightened. Repeat this procedure for the other four blade assemblies. 10. The blade flanges have an interlocking feature that must be fully engaged before tightening the screws. Make sure all the flanges are properly SWITCH HOUSING MOUNTING SCREW ASSEMBLY engaged and then tighten
Inhaltszusammenfassung zur Seite Nr. 6
How to Wire ! WARNING Your Ceiling Fan The outlet box must be securely anchored and capable of withstanding a load of at least 50 lbs. If you feel that you do not have enough electrical wiring knowledge or experience, have your fan WARNING installed by a licensed electrician. ! To reduce the risk of fire, electric shock, or personal ! WARNING injury, mount fan to outlet box marked acceptable for fan support, and use screws supplied with outlet To avoid possible electrical shock, be sure electric
Inhaltszusammenfassung zur Seite Nr. 7
3. Screw the two threaded studs (supplied) into the Maintenance tapped holes in the hanger bracket. IMPORTANT CARE INSTRUCTIONS 4. Lift the ceiling cover up to the threaded studs and for your Ceiling Fan turn until studs protrude through the holes in the ceiling cover (Figure 12). Periodic cleaning of your new ceiling fan is the only maintenance that is needed. 5. Secure the ceiling cover in place by sliding lockwashers over the threaded studs and installing the When cleaning, use only a soft br
Inhaltszusammenfassung zur Seite Nr. 8
! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose 2. Check line power connections to fan and switch wire switch wire connections in the switch housing. connections in the switch housing. ! WARNING: Make sure main
