Inhaltszusammenfassung zur Seite Nr. 1
Table of Contents
1 • Getting Ready ..................................................................................................................................................................................................................................................... 2
2 • Installing the Ceiling Mounting Plate .............................................................................................................................................................................
Inhaltszusammenfassung zur Seite Nr. 2
1 • Getting Ready Congratulations! Checking Your Fan Parts Your new Hunter ceiling fan is an addition to your home or office that Carefully unpack your fan to avoid damage to the fan parts. Refer to will provide comfort and reliable performance for many years. We are the included Parts Guide. Check for any shipping damage to the motor proud to supply you with the best ceiling fan available anywhere in or fan blades. If any parts are missing or damaged, contact your Hunter dealer or call Hunter
Inhaltszusammenfassung zur Seite Nr. 3
1 • Getting Ready (continued) Step 1 - Choose the Fan Site Proper ceiling fan location and attachment to the building structure are essential for safety, reliable operation, maximum efficiency, and energy savings. 30” From 8’ Minimum Choose a fan site where: Wall or Ceiling Height Nearest • No object can come in contact with the rotating fan blades Obstruction 7’ Minimum during normal operation. Blades to Floor • The fan blades are at least 7 feet above the floor and the ceiling is
Inhaltszusammenfassung zur Seite Nr. 4
1 • Getting Ready (continued) Step 2 - Cut the Ceiling Hole 2-1. Locate the site for the ceiling hole directly below the joist or support brace that will hold the outlet box and fan. 2-2. Cut a 4” diameter hole through the drywall or plaster of the ceiling. You will use the hole to install the support brace and outlet box. Step 3 - Install a Support Brace, If Necessary Determine if there is a ceiling joist directly above the ceiling hole. If the joist is there, determine if it is positione
Inhaltszusammenfassung zur Seite Nr. 5
2 • Installing the Ceiling Mounting Plate 2.1 2.2 Drill two 9/64” pilot holes into the wood support structure through the CAUTION: To avoid possible electrical shock, before installing your fan, outermost holes in the outlet box. disconnect the power by turning off the circuit breakers to the outlet box and associated wall switch location. If you cannot lock the circuit breakers in the off position, securely fasten a prominent warning device, such as a tag, to the service panel. 71 2.3 2.
Inhaltszusammenfassung zur Seite Nr. 6
2 • Installing the Ceiling Mounting Plate (continued) Note: The isolators must be flush against the ceiling. A loose ceiling mounting plate will result in improper operation of the Auto 2 2.5 2.6 Balance™system. 2 68 65 Align the slotted holes in the ceiling mounting plate (2) with the pilot Place a flat washer (68) on each of the two 3” wood screws (65). Insert holes you drilled in the wood support structure. For proper alignment, use the screws into the slotted holes in the ceiling m
Inhaltszusammenfassung zur Seite Nr. 7
3 • Assembling and Hanging the Fan CAUTION: 7 The motor cover adapter has a special coating on the threads. Do not remove 7 3 this coating; the coating prevents the pipe/ball assembly from 3.1 3.2 unscrewing. Once assembled, do not 4 3 remove the pipe/ ball assembly. 8 4 79 Insert the pipe/ball assembly (7) through the ceiling mounting plate cover Using the provided Allen wrench (79), loosen the setscrew (8) on the motor cover adapter to install the pipe and ball assembly (7). When
Inhaltszusammenfassung zur Seite Nr. 8
3 • Assembling and Hanging the Fan (continued) 3.5 3.6 Optional Pipe/Ball Instructions: Place the slots over the hooks to hang the fan. Your Hunter fan comes with an optional pipe/ball assembly extension pipe. If you would like to use the enclosed optional 6 inch pipe/ball TM assembly, follow Steps 3.6-3.9. Note: The Auto Balance system is designed for pipe/ball assemblies that are 6” and shorter. If you use a pipe/ TM ball assembly longer than 6 inches, do not activate the Auto Balance syst
Inhaltszusammenfassung zur Seite Nr. 9
3 • Assembling and Hanging the Fan (continued) 3.10 3.9 Optional Pipe/Ball Instructions: Optional Pipe/Ball Instructions: Remove the screw and ground wire from the pipe. Reassemble the ground wire, wedge, pin, ball, and pipe ball screw, in that order, onto the long pipe/ball assembly. Go back to Step 3.2. 4 4 •• S Se ettttiin ng g tth he e R Re em mo otte e T Tr ra an ns sm miitttte er r a an nd d R Re ec ce eiiv ve er r When two or more fans are located near 86 each other, you may wa
Inhaltszusammenfassung zur Seite Nr. 10
4 • Setting the Remote Transmitter and Receiver(cont.) Receiver 1 Receiver 2 D D IiP S p Switches witches D D IP S ip Switches witches Set to 01110 Set to 01001 Set to 0111 Set to 0100 Transmitter 1 Transmitter 2 4.3 4.2 Dip Switches Dip Switches DIP Switches DIP Switches 87 Set to 01110 Set to 01001 Toggle Switch Set to 0111 Set to 0100 Change the position of the DIP switches in the remote transmitter (87) and There is a toggle switch beside the DIP switches on the transmitter (87). the recei
Inhaltszusammenfassung zur Seite Nr. 11
5 • Wiring the Fan WARNING!: All wiring must be in accordance with national and local electrical codes and ANSI/NFPA 70. If you are unfamiliar with wiring, use a qualified electrician. Wall switches are not included. Select an acceptable general-use switch in accordance with national and local electrical codes. 70 5.1 Using a large wire connector (70), connect the ground wire (grounding) To connect the wires, hold the bare metal leads together and place a wire connector (70) over them, then t
Inhaltszusammenfassung zur Seite Nr. 12
5 • Wiring the Fan 5.2 5.3 Using the small wire connectors (70), connect the wires from the fan as follows: Using the large wire connectors (70), connect the white wire and the black wire from the ceiling as follows: • The black wire with a white stripe from the fan to the red wire from the receiver • The white (common) power wire from the ceiling to the white wire from (marked on white tag “LIGHT OUT”) the receiver (marked on red tag “NEUTRAL IN”) • The black wire from the fan to the black
Inhaltszusammenfassung zur Seite Nr. 13
6 • Installing the Ceiling Plate Cover 2 3 6.1 6.2 3 Tab 7 Groove Rotate the pipe/ball assembly (7) so the tab in the ceiling mounting plate Swing the fan up to align the ceiling mounting plate cover screw holes with the mounting holes on the ceiling mounting plate(2). cover (3) is secure in the hanger ball groove. Note: Your fan may have multiple tabs and grooves that must be aligned. 62 3 6.3 6.4 3 Holding the ceiling mounting plate cover (3) up with the screw holes Partially install a cei
Inhaltszusammenfassung zur Seite Nr. 14
6 • Installing the Ceiling Plate Cover(continued) 3 3 6.5 6.6 4 4 Align the tabs on the trim ring opposite the grooves in the hanger ball. Should you need to remove the trim ring, press firmly on opposite sides of Using both hands, push the ceiling mounting plate cover trim ring (4) up the trim ring (4) directly above the groove in the hanger ball. The tabs will flex out releasing the ceiling mounting plate cover trim ring (4). to the top of the ceiling mounting plate cover. The ceiling mounti
Inhaltszusammenfassung zur Seite Nr. 15
7 • Assembling the Blades (continued) 7.3 7.4 47 47 98 Loosen (DO NOT REMOVE) the blade-to-arm screws (47) that are holding Slide the blade arms (98) onto the blade-to-arm screws (47). Tighten the the shipping bumpers in place. Push the shipping bumpers in, then lift blade-to-arm screws (47) as tight as possible with a screwdriver. them off. TM 8 • Activating Auto Balance Note: After the retaining screws are removed, Red Retaining the blades will Screws feel loose. This is normal, as
Inhaltszusammenfassung zur Seite Nr. 16
9 • Completing Your Installation With or Without a Bowl Light Fixture 9.1 9.2 30 69 Partially install inner switch housing screws (69) into the switch housing Feed the upper plug connector through the center opening of the upper mounting plate. switch housing (30). 9.3 30 69 Your Hunter fan comes with an integrated light fixture assembly and an optional Align the keyhole slots in the upper switch housing with the inner switch switch housing cap and plug button. This feature gives you the opti
Inhaltszusammenfassung zur Seite Nr. 17
9 • Completing Your Installation With or Without a Bowl Light Fixture (cont.) Note: Both plug connectors are 30 polarized and will only fit together one way. Make sure the connectors are properly aligned before connecting 9.5 9.4 them. Incorrect connection could 131 cause improper operation and damage to the 31 product. Connect the upper plug connector from the fan body to the lower plug Place the lower switch housing assembly (31) over the upper switch connector in the lower swit
Inhaltszusammenfassung zur Seite Nr. 18
9 • Completing Your Installation With or Without a Bowl Light Fixture (cont.) 150 9.8 9.9 148 150 Place the cover plate (148) up against the glass bowl (150). Align the holes Lift the glass bowl (150) up so the threaded finial rod fits through the hole in the cover plate (148) with the grommet hole of the metal disc.. in the glass bottom. 9.10 9.11 149 Removing the Light Fixture Disconnect the plug connectors between the black wire and the black Screw the finial (149) onto the threaded finial
Inhaltszusammenfassung zur Seite Nr. 19
9 • Completing Your Installation With or Without a Bowl Light Fixture (cont.) 9.12 9.11 Removing the Light Fixture Removing the Light Fixture Unscrew the light bulb socket. Remove the nut and washer from inside the center of the lower switch housing. 9.13 9.14 Removing the Light Fixture Removing the Light Fixture Pull the large (male) plug connector through the hole in the center of the Remove the light fixture bracket by removing the 2 screws attaching the lower switch housing. Then, pull ou
Inhaltszusammenfassung zur Seite Nr. 20
9 • Completing Your Installation With or Without a Bowl Light Fixture (cont.) 9.15 Removing the Light Fixture After your installation is complete, restore power to the fan. Wash your Install the switch housing cap and plug button to the lower switch hands after installing the fan. housing. You can mount the remote holder to any toggle switch plate with the screws already in the switch plate. Or, you can simply mount the remote holder on the wall. 20 20 42798-01 • 09/16/09 • Hunter Fan Co
