Inhaltszusammenfassung zur Seite Nr. 1
READ AND SAVE THESE INSTRUCTIONS
®
™
MARIOL
Model No.
CF940AB00
Ceiling Fan
CF940AW00
Owner's Manual
CF940BC00
CF940PW00
Net Weight: 23.1 Lbs. CF940SCK00
CF940WB00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies to the motor, this warr
Inhaltszusammenfassung zur Seite Nr. 2
! WARNING WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
Inhaltszusammenfassung zur Seite Nr. 3
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Installed Wire Length Wire Size A.W.G. Tools Needed for Assembly Up to 50 ft. 14 One Phillips head screwdriver One stepladder 50-100 ft. 12 One 1/4” blade screwdriver One wire stripper One 5/16” open end wrench, or pliers Three wire connectors (supplied) ! WARNING MATERIALS Before assembly your ceiling fan, refer to section on Wiring outlet box and box connectors must be of
Inhaltszusammenfassung zur Seite Nr. 4
How to Put Your Ceiling Fan Together 1. Remove the hanger ball by loosening the setscrew 4. Make sure the grommet is properly installed in the in the hanger ball until the ball falls freely down the coupling cover, then slide the coupling cover on the downrod (Figure 1). Remove the pin from the downrod until it rests on the motor housing. Place downrod, then remove the hanger ball. Retain the the ceiling cover over the downrod. Be sure that pin and hanger ball for reinstallation in step 5. the c
Inhaltszusammenfassung zur Seite Nr. 5
SWITCH ! WARNING HOUSING CONNECTOR MOTOR To reduce the risk of personal injury, do not bend the CONNECTOR blade flange when installing the blade flanges, balancing the blades or cleaning the fan. Do not insert foreign objects in between rotating fan blades. 3/16-24 x 5/16" SLOTTED PHILLIPS PULL HEAD SCREW (3) CHAIN LATCH SWITCH BLADE WASHER (3) SWITCH HOUSING ASSEMBLY MOUNTING SCREWS (4) SLOT FOR PULL CHAIN SWITCH FAN BLADE Figure 7 BLADE FLANGE Figure 5 NOTE: The switch housing assembly must b
Inhaltszusammenfassung zur Seite Nr. 6
NOTE: CEILING COVER, How to Hang SUPPLY WIRES AND OUTLET FAN WIRES OMITTED BOX Your Ceiling Fan FOR CLARITY. ! WARNING The fan must be hung with at least 7' of clearance HANGER from floor to blades (Figure 9). BRACKET CEILING HANGER BALL/ Figure 11 DOWNROD ASSEMBLY ! WARNING To avoid possible fire or shock, do not pinch wires between the hanger ball/downrod assembly and AT LEAST 7' hanger bracket. Figure 9 FLOOR How to Wire ! WARNING Your Ceiling Fan The outlet box and joist must be securely mo
Inhaltszusammenfassung zur Seite Nr. 7
BLACK AND BLUE SUPPLY Using Your Ceiling Fan FAN WIRES GROUND GROUND WIRE WIRE 1. Restore electrical power to the outlet box by turning LISTED the electricity on at the main fuse box. WHITE SUPPLY WIRE (NEUTRAL) CONNECTOR (3) 2. Check the operation of the fan by gently pulling on the pull chain switch. 3. All fans are shipped from the factory with the reversing switch positioned to circulate air down- GREEN WIRE ward. If airflow is desired in opposite direction, turn (GROUND) FROM WHITE FAN HANG
Inhaltszusammenfassung zur Seite Nr. 8
! WARNING: FOR YOUR OWN SAFETY TURN OFF POWER AT FUSE BOX OR CIRCUIT BREAKER BEFORE TROUBLE SHOOTING YOUR FAN. Trouble Shooting TROUBLE PROBABLE CAUSE SUGGESTED REMEDY 1. Fan will not start. 1. Fuse or circuit breaker blown. 1. Check main and branch circuit fuses or circuit breakers. 2. Loose power line connections to the fan, or loose 2. Check line power connections to fan and switch wire switch wire connections in the switch housing. connections in the switch housing. ! WARNING: Make sure main
