Inhaltszusammenfassung zur Seite Nr. 1
READ AND SAVE THESE INSTRUCTIONS
®
DESIGNER REMOTE
Model No.
Series
CF759OB00 CF759PB00
Ceiling Fan
CF759TG00 CF759HTW00
Owner's Manual
CF759BS00 CF759AB00
Net Weight: 17.3 Lbs. CF759WW00
LIMITED WARRANTY
What The Warranty Covers:
This warranty covers the motor and the other components and accessories of your Emerson ceiling fan against all defects in workmanship and materials.
You must be the original purchaser or user of the product to be covered.
What The Period Of Coverage Is:
As it applies
Inhaltszusammenfassung zur Seite Nr. 2
WARNING ! WARNING: To avoid fire, shock, and serious personal injury, follow these instructions. Safety Instructions 1. Read your owner’s manual carefully and keep it for future reference. 2. Before servicing or cleaning unit, switch power off at service panel and lock service panel disconnecting means to prevent power from being switched on accidentally. When the service disconnecting means cannot be locked, securely fasten a warning device, such as a tag, to the service panel. 3. Be careful of
Inhaltszusammenfassung zur Seite Nr. 3
This Manual Is Designed to Make it as Easy as Possible for You to Assemble, Install, Operate and Maintain Your Ceiling Fan Tools Needed for Assembly One Phillips head screwdriver One stepladder One 1/4” blade screwdriver One wire stripper Installed Wire Length Wire Size A.W.G. Three wire connectors (supplied). Up to 50 ft. 14 50-100 ft. 12 WARNING ! MATERIALS Before assembly your ceiling fan, refer to section on Wiring outlet box and box connectors must be of type proper method of wiring your fa
Inhaltszusammenfassung zur Seite Nr. 4
3. Make sure the grommet is properly installed in the How to Put Your Ceiling coupling cover, then slide the coupling cover on the downrod until it rests on the motor housing. Fan Together Place the ceiling cover over the downrod. Be sure 1. Remove the hanger ball by loosening the setscrew that the ceiling cover and the coupling cover are in the hanger ball until the ball falls freely down the both oriented correctly (Figure 3). downrod (Figure 1). Remove the pin from the downrod, then remove th
Inhaltszusammenfassung zur Seite Nr. 5
NOTE: Remove and discard the four shipping 7. Remove the three switch housing mounting screws (Figure 5) from the switch housing plate. Position spacers and screws from the motor hub. the switch housing assembly on the switch hous- 10. Loosely attach one blade assembly to the motor ing plate and align the holes in the switch housing hub using two 1/4-20 x 1/2” Phillips oval head assembly with the holes in the plate. Secure the flange screws. Make sure the screws are NOT switch housing assembly b
Inhaltszusammenfassung zur Seite Nr. 6
! WARNING ! WARNING To avoid fire or shock, follow all wiring instructions Hanger bracket must seat firmly against outlet box. If carefully. the outlet box is recessed, remove wall board until bracket contacts box. If bracket and/or outlet box are Any electrical work not described in these not securely attached, the fan could wobble or fall. instructions should be done or approved by a licensed electrician. ! WARNING How to Hang Your Failure to seat tab in groove could cause damage to electrical
Inhaltszusammenfassung zur Seite Nr. 7
BLACK AND BLUE SUPPLY Setting Remote Control FAN WIRES GROUND GROUND WIRE WIRE Operating Frequency LISTED WHITE SUPPLY WIRE Your Emerson Remote Control Fan receiver and (NEUTRAL) CONNECTOR (3) transmitter can be set to operate at one of 16 different frequencies. In most cases you will not need to change the factory set frequency. The frequency should only need to be changed for one of the GREEN WIRE following reasons: (GROUND) FROM WHITE FAN HANGER BRACKET WIRE a. Multiple fans in one location t
Inhaltszusammenfassung zur Seite Nr. 8
SWITCH Operation of Your LEVERS Remote Control SWITCH LEVERS 1. To set the desired fan speed, push the HI, MED or LOW buttons to set your fan on high, medium or low speed. (See Figure 17). 2. To reverse the direction the fan is turning, press the FOR/REV button. The direction the fan turns will change each time the FOR/REV button is pressed. 3. To turn the fan OFF press the FAN/OFF button. 4. To set the level of light brightness, press and hold the LIGHT DIMMER button. The light brightness Figur
Inhaltszusammenfassung zur Seite Nr. 9
Maintenance Accessories 1. Ceiling Fan Light Kits (see store or catalog). IMPORTANT CARE INSTRUCTIONS 2. Downrod Kits (see store or catalog). for your Ceiling Fan Periodic cleaning of your new ceiling fan is the only maintenance that is needed. ! WARNING When cleaning, use only a soft brush or lint free cloth The use of any other control not specifically to avoid scratching the finish. approved for this fan could result in fire, shock and personal injury. Abrasive cleaning agents are not require
Inhaltszusammenfassung zur Seite Nr. 10
Repair Parts Listing Part Numbers Key Model No. Model No. Model No. Model No. Model No. Model No. Model No. No. Description CF759AB00 CF759PB00 CF759OB00 CF759TG00 CF759BS00 CF759HTW00 CF759WW00 * Hanger Ball Assembly, 760750 760750-1 760750-36 760750-37 760750-24 760750-34 760750-3 Consisting of: 1 Hanger Bracket — — — — — — — 2 Hanger Ball — — — — — — — 3 Downrod — — — — — — — * Parts Bag Containing: 761538-6 761538-5 761538-8 761538-8 761538-7 761538-5 761538-5 4 Wire Connector (3) — — — — —
