Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION and SERVICE INSTRUCTIONS
USE and CARE INSTRUCTIONS
BUILT-IN GAS HOBS
DEGH60
DEGH60ST
DEGH60WT
distributed by
DèLonghi
Pty Ltd
Inhaltszusammenfassung zur Seite Nr. 2
Dear Customer, Thank you for having purchased and given your preference to our product. The safety precautions and recommendations reported below are for your own safety and that of others. They will also provide a means by which to make full use of the features offered by your appliance. Please keep this booklet in a safe place. It may be useful in future, either to yourself or to others in the event that doubts should arise relating to its operation. This appliance must be used only for the ta
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT PRECAUTIONS AND RECOMMENDATIONS FOR USE OF ELECTRICAL APPLIANCES Use of any electrical appliance implies the necessity to follow a series of fundamental rules. In particular: ■ Never touch the appliance with wet hands or feet; ■ do not operate the appliance barefooted; ■ do not allow children or other incapable people to use the appliance without supervision. The manufacturer cannot be held responsible for any damages caused by improper, incorrect or illogical use of the appliance. IMP
Inhaltszusammenfassung zur Seite Nr. 4
min 100 550 580 INSTALLATION CAUTION: ■ This appliance must be installed in accordance with these installation instructions, local gas fitting regulations, municipal building codes, water supply regulations, electrical wiring regulations, AS5601 / AG 601 - Gas Installations and ony other relevant statutory regulations. ■ This appliance shall only be serviced by authorized personnel. ■ This appliance is to be installed only by an authorised person. ■ Incorrect installation, for which the manu
Inhaltszusammenfassung zur Seite Nr. 5
100 mm min 500 mm This cooktop has been designed and constructed in accordance with the following codes and specifications: AGA101 (AS 4551) Approval Requirements for Domestic Gas cooking appliances AS/NZS 60335-1 General Requirements for Domestic electrical appliances AS/NZS 60335-2-6 Particular Requirements for Domestic electrical cooking appliances AS/NSZ 1044 Electromagnetic Compatibility Requirements. CLEARANCES: Installation clearances and protection of combustible surfaces shall comply wi
Inhaltszusammenfassung zur Seite Nr. 6
The installation shall comply with the dimensions in Figures 1 and 2, bearing in mind that: ■ A minimum clearance of 20 mm has to be kept between the bottom of the cooking hob and the top of an appliance or a shelf. To ensure this clearance mount the spacers, supplied with the appliance, as shown in the figure below. ■ A partition between the base of the hob and the cupboard below should be fitted 100 mm below the workbench surface if the cupboard is to be used for storage. ■ Overhead clearance
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION (Refer to Figure 4): 1. Spread out the gasket “C” over the workbench at the edge of the cut out tak- ing care to overlap the gasket at the corners. 2. Slot in the cooking hob into the cut out of the workbench and locate it cor- rectly. 3. Adjust the clamps “A” and tighten the screws “B” until the hob is firmly secured. 4. Using a sharp tool, trim any excess gasket which protrudes from the edge of the hob. Take care not to damage the countertop. Figure 4 C B A 7 20 mm min. 40 mm max.
Inhaltszusammenfassung zur Seite Nr. 8
GAS SUPPLY: ■ This appliance is suitable for use with Natural Gas or ULPG. (Check the “gas type” sticker attached to the appliance). ■ For Natural Gas the gas supply must be regulated to obtain a pressure of 1 kPa with the two semi-rapid (SR) burners operating. ■ For ULPG models connect the gas supply directly to the appliance test point adap- tor (supplied with the conversion kit) and ensure that the supply pressure is regulat- ed to 2.75 kPa. ■ Do NOT force the ”elbow“ rotation prior to loosen
Inhaltszusammenfassung zur Seite Nr. 9
5. Check the minimum burner setting by quickly rotating the gas control knob from the maximum to the minimum position, the flame must not go out. If adjustment is required carry out the “minimum burner setting adjustment" procedure described below. 6. If satisfactory performance cannot be obtained, the installer shall check the installa- tion and notify the local gas supply authority for a gas supply problem, or if it is an appliance problem, our Customer Service Centre should be called to obtai
Inhaltszusammenfassung zur Seite Nr. 10
CONVERSION PROCEDURE (to convert to Natural gas or to ULPG) REPLACING THE INJECTORS The conversion procedure must be carried out only by an authorised person. This appliance is suitable for use with Natural gas or ULPG (check the “gas type” stick- er attached to the appliance). The nominal gas consumption and injector size details are provided in table at page 9. To replace the injectors proceed as follows: ■ Remove pan supports and burners from the cooktop. ■ Using a spanner, remove the injecto
Inhaltszusammenfassung zur Seite Nr. 11
MINIMUM BURNER SETTING ADJUSTMENT Check whether the flame spreads to all burner ports when the burner is lit with the gas tap set to the minimum position. If some ports do not light, increase the minimum gas rate setting. Check whether the burner remains lit even when the gas tap is turned quickly from the maximum to the minimum position. If the burner does not remain lit, increase the minimum gas rate setting. The procedure for adjusting the minimum gas rate setting is described below. Fo
Inhaltszusammenfassung zur Seite Nr. 12
ELECTRICAL REQUIREMENTS: WARNING: ■ THIS APPLIANCE MUST BE EARTHED. CAUTION: ■ Ensure that the power outlet is properly earthed before connecting the appliance. ■ Disconnect power before servicing the appliance. The appliance is provided with a standard 240VAC three pin plug and power 2 cable (3 x 0.75 mm ). The wires in the power cable are coloured in accordance with the following code: Green/Yellow = Earth, Blue = Neutral, Brown = Active. If the colours of the wires in the power cable to the
Inhaltszusammenfassung zur Seite Nr. 13
USE and CARE CAUTION: ■ This appliance must be used only for the task it has explicitly been designed for, that is for domestic cooking of foodstuffs. Any other form of usage is to be con- sidered as inappropriate and therefore dangerous. Do not use this appliance as a space heater. ■ Do NOT place combustible materials or products on this appliance at any time. ■ Do NOT spray aerosols in the vicinity of this appliance while it is in use. ■ Before using for the first time, clean the cooktop with
Inhaltszusammenfassung zur Seite Nr. 14
GAS HOB Figure 11a Figure 11b 2 2 3 3 4 4 1 1 5 6 7 8 5 6 7 8 mod. DEGH60ST mod. DEGH60 mod. DEGH60WT ■ The electric ignition is incorporated in ■ The hob is fitted with a safety cut-out the knobs device ■ This appliance is class 3 ■ The electric ignition is incorporated in the knobs ■ This appliance is class 3 GAS BURNERS Natural Gas Propane gas MJ/h MJ/h 1. Triple ring burner (TR) 11.9 11.9 2. Left semi-rapid burner (SR) 6.3 6.3 3. Right semi-rapid burner (SR) 6.3 6.3 4. Auxiliary burner (A) 3
Inhaltszusammenfassung zur Seite Nr. 15
LIGHTING GAS BURNERS ■ Check that the electricity is switched on to allow spark ignition. ■ Make sure that all controls are turned to zero. ■ The gas flow to the burner is controlled by the knobs on the safety taps. ■ You control the flow by turning the knob indicator to line up with the following symbols: – Symbol : tap closed (burner off) – Symbol : High (maximum) – Symbol : Low (minimum) ■ To ignite automatically, simply push the required knob down and turn it to max- imum, keep the knob
Inhaltszusammenfassung zur Seite Nr. 16
Lighting the burners WITH ELECTRIC IGNITION (without safety cut-off valve) mod. DEGH60WT - DEGH60ST To light one of the burners, press and turn the corresponding knob to the maximum flow position (large flame) and keep the knob pressed down until the gas is lit. Turn the gas tap to the position required. Whenever lighting any of the burners produces an abnormal flame, switch that burner off and relight using the minimum setting. If after relighting the burner, the flame is still abnormal, turn
Inhaltszusammenfassung zur Seite Nr. 17
COOKING HINTS FOR GAS HOBS The burner must be chosen according to the diameter of the pans and energy required. For optimum efficiency use a wok or pan no smaller than 230mm diameter. Figure 13 do not use pans with concave or convex bases Burners Pan diameter Auxiliary 12 - 14 cm * Semi-rapid 16 - 20 cm Triple ring 24 - 28 cm Wok max 36 cm ( ) with grill for small cookware: minimum diameter 6 cm. * Saucepans with handles which are excessively heavy, in relationship to the weight of the pan, are
Inhaltszusammenfassung zur Seite Nr. 18
CORRECT USE OF TRIPLE-RING BURNER ■ The flat-bottomed pans are to be placed directly onto the pan-support. ■ To use the WOK, you must place the wok stand in the CORRECT position as shown in fig. 15a - 15b. IMPORTANT: The special grille for wok pans (figs. 15a, 15b) MUST BE PLACED ONLY over the pan- rest for the triple-ring burner. mod. DEGH60WT - DEGH60ST Figure 15a WRONG CORRECT mod. DEGH60 Figure 15b WRONG CORRECT 18
Inhaltszusammenfassung zur Seite Nr. 19
Cleaning and Maintenance GENERAL TIPS ■ Before cleaning the hob switch it off and wait for it to cool down. ■ Clean with a cloth, hot water and soap or liquid detergent. ■ Do not use products which are abrasive, corrosive or chlorine based. ■ Do not use steel pads. ■ Do not leave acid or alkaline substances (vinegar, salt, lemon juice, etc.) on the hob. ENAMELLED PARTS ■ All the enamelled parts must be washed only with a sponge with soapy water or other non-abrasive products. ■ Dry preferably w
Inhaltszusammenfassung zur Seite Nr. 20
GAS TAPS ■ Regular lubrication of the gas taps must only be performed by Authorised person. ■ If the gas taps are not working properly, call our Customer Service Centre to obtain the nearest Authorised Delonghi Service Agent. CORRECT POSITIONING OF THE BURNERS ■ It is very important to check that spreader F and cap C of the burner (see Figures 16 and 17) are perfectly in place because if they move out of place serious problems could arise. ■ Make sure that electrode S (Fig. 16) is kept clean so
