Inhaltszusammenfassung zur Seite Nr. 1
MONARCH INSTRUMENT
Instruction Manual
Monarch 314
Datalogging Humidity Temperature Meter
15 Columbia Drive
Amherst, NH 03031-2334 USA
Phone: (603) 883-3390
Fax: (603) 886-3300
© Monarch Instrument 2002 all rights reserved
E-mail: support@monarchinstrument.com
Website: www.monarchinstrument.com
1071-8041-210
Inhaltszusammenfassung zur Seite Nr. 2
LIMITED WARRANTY Safeguards and Precautions SELLER warrants hardware products to be free from any defect in materials or workmanship for a period of one (1) year from date of shipment to BUYER. SELLER’s entire liability and BUYER’s sole and exclusive remedy resulting from any defect in workmanship or material 1. Read and follow all instructions in this manual in the hardware product covered by this limited warranty shall be limited to and fully carefully, and retain this manual for future refer
Inhaltszusammenfassung zur Seite Nr. 3
MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER DECLARATION OF CONFORMITY Table of Contents Section Page Monarch Instrument Division of Monarch International Inc. 1.0 Introduction.................................................................................................................1 15 Columbia Drive, Amherst NH 03031 USA declares that the product: 2.0 Specifications..........................................................................................................
Inhaltszusammenfassung zur Seite Nr. 4
MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER Notes 1.0 Introduction This instrument is a dual channel, recording digital Humidity / Temperature meter providing simultaneous display of ambient humidity and temperature on the first channel, and a wide range temperature only measurement on the second channel. The first channel incorporates a polymer capacitive humidity sensor and a semiconductor temperature sensor (T1) in a detachable probe. The second channel employs a Type K thermocou
Inhaltszusammenfassung zur Seite Nr. 5
Notes MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER 3.0 Symbol Definitions and Feature Locations: : Low battery indication. Battery voltage is not sufficient for proper operation. : Indicates ‘Auto Power Off’ is enabled : Indicates that the display data is being held MAX : The Maximum value is now being displayed MIN : The Minimum value is now being displayed REC : Indicates that the instrument is recording. When flashing, the memory is full. Y : Indicates year is displayed in
Inhaltszusammenfassung zur Seite Nr. 6
MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER 7.3 DataLogger 4.0 Operating Instructions: Select DataLogger from the menu to load recorded data from the humidity meter. A 4.1 Preparation for Measurement progress bar will show how many bytes should be loaded and how many bytes have Measurement of ambient humidity and temperature (T1) may be made with the probe been received. When data is loaded successfully, three new windows appear a
Inhaltszusammenfassung zur Seite Nr. 7
MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER 4.8 Recording Interval Setup 6.0 Setup TestLink (Humidity DataLogger) - RS232 Interface To set the recording interval: Software: 1. Press and hold the MAX MIN button and then power on The TestLink package contains: the meter. 1. Two 3.5” diskettes 2. Custom designed RS232 cable for TestLink 2. Press HOLD (interval). System Requirements: Windows 95, Windows 98 or Windows NT 4
Inhaltszusammenfassung zur Seite Nr. 8
MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER MODEL 314 DATALOGGING HUMIDITY TEMPERATURE METER 5.3 Notes on Humidity and Temperature Calibrations Appendix: Thermocouple Probe Specifications 1. While performing the humidity calibration, the environment should be maintained at Model Range Tolerances Description stable conditions (i.e. constant temperature and constant humidity) to optimize the TP-K01 -50°C to 200°C ±2.2°C or ±0.75% Teflon insulation. Maximum insulation accuracy. W
