Inhaltszusammenfassung zur Seite Nr. 1
™ ™
MODELS 1420, 1620, 1720, 1920, AND 2120
HIGH PERFORMANCE AIRLESS SPRAYER
OWNER’S MANUAL • READ THIS MANUAL FOR COMPLETE INSTRUCTIONS
This pump is available in two models: a
TABLE OF CONTENTS:
stand model and a cart model. The cart
SAFETY . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3
model is shown in this manual. All
COMPONENTS AND DESCRIPTION . . . . . . . . . . . . . . . . . . 4
information given for the cart model
SETUP . . . . . . . . . . . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY INFORMATION • READ ALL SAFETY INFORMATION BEFORE OPERATING THE EQUIPMENT HAZARD: INJECTION INJURY HAZARD: EXPLOSION OR FIRE Solvent and paint fumes can explode or ignite. A high pressure paint stream produced by Property damage and/or severe injury can occur. this equipment can pierce the skin and underlying tissues, leading to serious injury PREVENTION: and possible amputation. SEE A PHYSICIAN • Provide extensive exhaust and fresh air IMMEDIATELY. introduction to keep the air within t
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INFORMATION • READ ALL SAFETY INFORMATION BEFORE OPERATING THE EQUIPMENT HAZARD: GENERAL GROUNDING INSTRUCTIONS Can cause severe injury or property damage. This product must be grounded. In the event of an electrical PREVENTION: short circuit, grounding reduces the risk of electric shock by • Read all instructions and safety precautions before providing an escape wire for the electric current. This product operating equipment. is equipped with a cord having a grounding wire with an • Fol
Inhaltszusammenfassung zur Seite Nr. 4
SPRAY l COMPONENTS AND DESCRIPTION sprayer model (refer to Spray COMPONENTS Gun/Tip Chart, below). The shipping carton for your painting system contains the following: Spray Hose ......................The spray hose connects the gun to • Suction set and return tube the pump. • Spray gun with filter • Spray tip assembly (see chart below) Return Tube......................Fluid is sent back out through the return tube to the original container. • 50 foot long, 1/4 inch diameter pressure hose • Sep
Inhaltszusammenfassung zur Seite Nr. 5
SETUP--ASSEMBLING THE SPRAYER TOOLS NEEDED FOR SETUP ATTACHING THE SPRAY GUN • Two adjustable wrenches 1. Thread spray gun • 3/16” allen wrench onto the other end of the hose. • Extension cord (refer to Important Electrical Information (page 3). Hold the gun with one adjustable wrench, and tighten with the other. ATTACHING THE SUCTION SET & RETURN TUBE 1. Attach the suction tube to the inlet valve and tighten firmly WARNING by hand. Be sure that the threads are straight so that the fitting turn
Inhaltszusammenfassung zur Seite Nr. 6
SPRAY o o BEFORE YOU BEGIN CHOOSING THE CORRECT SPRAY GUN FILTER This column contains instructions that will be repeated Use the proper gun filter based on the tip size being used. throughout this manual. Part No. Tip Size Filter Mesh Color of Qty. Filter Type Number PLUGGING IN THE SPRAYER Body 0154918 .011 Extrafine 180 mesh red 2 pack 1. Check that the ON/OFF 0.084 mm switch is in the OFF position. 0154675 .013 - .015 Fine 100 mesh yellow 2 pack 0.140 mm 0154842 .017 - .023 Medium 50 mesh wh
Inhaltszusammenfassung zur Seite Nr. 7
l SPRAY SPRAY SPRAY o PURGING & PRIMING PURGING AND PRIMING THE PUMP PURGING AND PRIMING THE SPRAY HOSE 1. Unlock the spray gun and 1. Place a full container of turn PRIME/SPRAY knob paint underneath the Suction to PRIME. tube suction tube. 2. Secure the return tube Return Your spray tip SHOULD into a waste container. tube NOT be attached to your spray gun when purging your spray hose. 2. Trigger and HOLD the spray gun into a waste container. 3. While holding the trigger, 3. Turn the pressure c
Inhaltszusammenfassung zur Seite Nr. 8
SPRAYING PRACTICE TIP: Keep the spray gun perpendicular to the surface, otherwise one end of the pattern will be thicker than the other. CAUTION Approximately Be sure that the paint hose is free of kinks and clear of 10 to 12 inches objects with sharp cutting edges. 1. Switch the pump ON (l) Right way PRIME and turn the PRIME/SPRAY knob to SPRAY. Wrong way 2. Turn the pressure contol dial to its highest setting (+). The spray hose TIP: Keep the spray gun at right angles to the should stiffen as
Inhaltszusammenfassung zur Seite Nr. 9
SPRAYING TROUBLESHOOTING CLEANING THE SPRAY GUN FILTER The following is a short list of minor difficulties you might encounter while spraying. If any of these occur, it will Filter top This filter must be cleaned every time reduce the flow of paint, making your spray pattern poor, or you use your sprayer. paint will fail to spray from the gun. When using thicker paints, the filter • Clogged spray tip might need to be cleaned more often. • Clogged gun filter 1. Perform Pressure Relief • Clogged
Inhaltszusammenfassung zur Seite Nr. 10
l l SPRAY o CLEANUP PURGING THE PAINT HOSE CLEANING THE SUCTION SET IMPORTANT CLEANING 1. Lock the gun and turn These steps will allow you to NOTES! the pump OFF (O). recover excess paint left over in the 2. Remove the suction paint hose. hose and return tube READ THESE NOTES AND and clean it using the 1. Lock the gun and remove spray tip WARNINGS BEFORE YOU appropriate cleaning assembly. solution. 2. Submerge suction set into a bucket START TO CLEAN YOUR with appropriate cleaning solution. Yo
Inhaltszusammenfassung zur Seite Nr. 11
o CLEANUP (CONTINUED) CLEANING THE SPRAY GUN FILTER AND TIP ASSEMBLY 1. Make sure the pump is switched OFF (O), the 5 Clean spray tip and filter with a soft-bristled brush and the appropriate cleaning solution. Be sure to remove and PRIME/SPRAY knob is turned to PRIME, and unplug the clean the washer and saddle seat located in the rear of sprayer. the spray tip assembly. 2. Remove spray gun from the paint hose using adjustable Saddle Washer wrenches. seat 6. Reassemble spray gun: • install gun
Inhaltszusammenfassung zur Seite Nr. 12
l SPRAY o STORAGE SHORT-TERM STORAGE (UP TO 16 HOURS) PREPARING THE SPRAYER FOR LONG- TERM STORAGE Follow these steps when using latex paints only. If 1. Fill a cup or other container with separating oil using materials that are oil-based, follow the long-term storage steps. (approximately 2 ounces) supplied with the unit and submerge the inlet valve into the oil. SHUTDOWN 1. Lock the spray gun off. GX-06/07 GX-08/10 2. Turn the PRIME/SPRAY knob to PRIME. 2. Place a rag over the spray hose por
Inhaltszusammenfassung zur Seite Nr. 13
MAINTENANCE ACCESSORIES Part # Description DAILY MAINTENANCE 0279920 Separating Oil The only daily maintenance necessary is thorough cleaning. 0154830 Hose, Whip End, 5’ x 3/16” Follow the cleaning procedures in this manual. 0270192 Hose, Wireless, 25’ x 1/4" 0291000 Hose, Wireless, 50’ x 1/4" EXTENDED MAINTENANCE 0279667 Hose Connector, 1/4” x 1/4” 0088154 Pressure Gauge Some pump parts eventually wear out from use and must be 0508910 Tip Extension, 12” replaced. The following list indicates th
Inhaltszusammenfassung zur Seite Nr. 14
FLUID SECTION SEAL REPLACEMENT INSTRUCTIONS KIT 0512221 (MODELS 1420 AND 1620) KIT 0512178 (MODELS 1720, 1920, 2120) WARNING Always wear protective eye wear while servicing the pump. Be sure to follow the PRESSURE RELIEF PROCEDURE (page 6) when shutting the unit down for any purpose, including servicing or adjusting. After performing the pressure relief procedure, be sure to unplug the unit before servicing or adjusting. Area must be free of solvents and paint fumes. yoke area to prolong life
Inhaltszusammenfassung zur Seite Nr. 15
TROUBLESHOOTING PROBLEM CAUSE SOLUTION A. The sprayer does not start. 1. The sprayer is not plugged in. 1. Plug the sprayer in. 2. The ON/OFF switch is set to OFF. 2. Turn the ON/OFF switch to ON. 3. The sprayer was turned off while still under 3. Turn pressure control knob to maximum setting (+), pressure. or relieve pressure by turning the PRIME/SPRAY valve to PRIME. 4. No voltage is coming from the wall plug. 4. Properly test the power supply voltage. 5. The extension cord is damaged or has t
Inhaltszusammenfassung zur Seite Nr. 16
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS GX-06/07 (1420, 1620, 1720) SUCTION SET • DISPOSITIF D’ASPIRATION • JUEGO DE SUCCIÓN 1 5 2 3 4 1 5 2 6 3 ENGLISH (1420) Item Part # Description Quantity 1 0512120 Plastic gun assembly............................1 4 0512121 Metal gun assembly..............................1 2 0501011 Guard Assembly ...................................1 3 0501413 Tip* ........................................................1 4 0154675 Filter assembly, 100 mesh..........
Inhaltszusammenfassung zur Seite Nr. 17
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS FRANÇAIS GX-08 (1920) ArticleN° de pièce Description Quantity 1 Se reporter à la liste d’ACCESSOIRES 8 2 0501011 Protège-embout ....................................1 7 9 3 0296261 Diffuseur, 2,2 cm...................................1 6 4 0296270 Ressort de soupape .............................1 10 5 5 0296230 Protège-doigts ......................................1 11 4 6 0296285 Détente et ses composants..................1 12 3 7 0296284 Vis de déten
Inhaltszusammenfassung zur Seite Nr. 18
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS FRANÇAIS ArticleN° de pièce Description Quantity 8 1 Se reporter à la liste d’ACCESSOIRES 7 9 2 0501011 Protège-embout ....................................1 6 3 0296261 Diffuseur, 2,2 cm...................................1 10 5 4 0296270 Ressort de soupape .............................1 11 4 5 0296230 Protège-doigts ......................................1 12 3 6 0296291 Détente et ses composants..................1 7 0296284 Vis de détente (courte) .
Inhaltszusammenfassung zur Seite Nr. 19
PARTS LIST • LISTE DE PIÈCES • LISTA DE PIEZAS 1 2 3 5 1420 6 7 8 4 9 10 11 6 9821503 Rondelle (1620, 1720, 1920) . . . . . . .4 ENGLISH 7 9810111 Écrou (1620, 1720, 1920) . . . . . . . . .4 0288661 Gros écrou papillon (2120) . . . . . . . .4 Item Part # Description Quantity 8 0512383 Chariot (1620) . . . . . . . . . . . . . . . . . .1 1 0512336 Stand (1420) . . . . . . . . . . . . . . . . . . . .1 0512368 Chariot (1720) . . . . . . . . . . . . . . . . . .1 0512369 Handle (1620, 1720) . . . . .
Inhaltszusammenfassung zur Seite Nr. 20
LIMITED WARRANTY AIRLESS PAINT SPRAY EQUIPMENT This product, manufactured by Wagner Spray Tech Corporation (Wagner), is warranted to the original retail purchaser against defects in material and workmanship for one year from date of purchase. This warranty does not cover damage resulting from improper use, accidents, user's negligence or normal wear. This warranty does not cover any defects or damages caused by service or repair performed by anyone other than a Wagner Authorized Service Center.
