Inhaltszusammenfassung zur Seite Nr. 1
texture paint spray gun
66103
set up and Operating instructiOns
®
distributed exclusively by Harbor Freight t ools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
read this material before using this product.
Failure to do so can result in serious injury.
sa Ve tHis manual.
© ®
Copyright 2008 by Harbor Freight Tools . All rights reserved. No portion of this manual or any artwork
contained herein may be reproduced in any shape or form withou
Inhaltszusammenfassung zur Seite Nr. 2
nOtice is used to sa Ve tHis manual address practices Keep this manual for the safety warn- not related to personal injury. ings and precautions, assembly, operat- cautiOn, without ing, inspection, maintenance and cleaning the safety alert procedures. Write the product’s serial symbol, is used to address number in the back of the manual near the practices not related to assembly diagram (or month and year of personal injury. purchase if product has no number). Keep this manual and
Inhaltszusammenfassung zur Seite Nr. 3
sure to high intensity noise is able to personal safety cause hearing loss. a. Stay alert. Watch what you are do- h. risk of electric shock. this t ex- ing and use common sense when ture spray paint gun is not pro - operating. Do not use while tired vided with an insulated gripping or under the influence of drugs, al- surface. Contact with a ″live″ wire will cohol, or medication. A moment of also make exposed metal parts of the inattention while operating increases tool ″live″ and shock
Inhaltszusammenfassung zur Seite Nr. 4
e. maintain the tool with care. Keep b. Never use oxygen, carbon dioxide, this tool clean. A properly maintained combustible gases or any bottled tool is easier to control. gas as an air source for the tool. Such gases are capable of explosion f. check for misalignment or bind - and serious injury to persons. ing of moving parts, breakage of parts, and any other condition that sa Ve tHese affects the tool’s operation. If dam- aged, have the tool serviced before instructiOns. using. Man
Inhaltszusammenfassung zur Seite Nr. 5
Your risk from these exposures var- Symbol Definitions ies, depending on how often you do symbol property or statement this type of work. To reduce your exposure to these chemicals: work in WARNING marking concerning Risk a well ventilated area, and work with of Explosion. approved safety equipment, such as those dust masks that are specially Specific Safety Instructions designed to filter out microscopic particles. (California Health & Safety 1. CAUTION: To prevent serious injury: Co
Inhaltszusammenfassung zur Seite Nr. 6
ups to ensure medical problems are not being caused or worsened from use. Pregnant women or people who have impaired blood circulation to the hand, past hand injuries, ner- vous system disorders, diabetes, or Raynaud’s Disease should not use this tool. If you feel any medical or physical symptoms related to vibra- tion (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nico- tine reduces the blood supply to th
Inhaltszusammenfassung zur Seite Nr. 7
air supply FunctiOnal descriptiOn tO preVent Specifications explOsiOn: use only clean, dry, regulated, Operating Air Pressure 25 - 90 PSI compressed air to power this Range tool. do not use oxygen, Maximum Air Pressure 90 PSI carbon dioxide, combustible Air Inlet 1/4” -18 NPS gases, or any other bottled Air Consumption 7 CFM @ 25 PSI gas as a power source for this 4 mm (5/32”) tool. Nozzle Size 6 mm (15/64”) 8 mm (5/16”) note: The use of an in-line air and water Hopper Capacity 1.5 g
Inhaltszusammenfassung zur Seite Nr. 8
operate accidentally after the air discharge the tool in a safe fashion supply is disconnected. after disconnecting to ensure that the tool is disconnected and not pow- note: Air flow, and therefore tool perfor- ered. mance, can be hindered by under- sized air supply components. Operating instructiOns 2. The air hose must be long enough read the entire impOrtant to reach the work area with enough saFety inFOrmatiOn extra length to allow free movement while working. section at the beginni
Inhaltszusammenfassung zur Seite Nr. 9
4. Using two hands, one to steady the Work piece and Work area set up Plastic Hopper and the other to oper- 1. This Texture Paint Spray Gun is ate the Texture Paint Spray Gun, aim meant for spraying heavy viscos- the Spray Gun Nozzle at the surface ity products like rubberized decking to be covered. nOte: it may take a materials, texture coatings for interior few times to mix the proper spray and exterior walls, heavy water proof- solution. Do not fill the Plastic ing materials, and t
Inhaltszusammenfassung zur Seite Nr. 10
8. When you are completely finished or tO preVent are stopping for the day, disconnect seriOus injury and empty the Plastic Hopper. Flush FrOm accidental the system with fresh cold water. OperatiOn: Rinse and clean the Plastic Hop- t urn off the tool, detach the per and the Gun Body and let both air supply, safely discharge dry completely before storing inside, any residual air pressure in away from children. the tool, and release the gun t rigger before performing any 9. If the tool
Inhaltszusammenfassung zur Seite Nr. 11
t roubleshooting problem possible causes likely solutions Decreased output. 1. Not enough air pressure and/ 1. Check for loose connections and make sure or air flow. that air supply is providing enough air flow (CFM) at required pressure (PSI) to the tool’s air inlet. do not exceed maximum air pressure. 2. Obstructed trigger. 2. clean around trigger to ensure free movement. 3. Blocked air inlet screen (if 3. Clean air inlet screen of buildup. equipped). 4. Air leaking from loose 4. Make
Inhaltszusammenfassung zur Seite Nr. 12
parts list parts list part description Q’ty part description Q’ty 1 Retaining Ring 1 8F Fluid Control Knob 1 2A 4.0 mm (3/16”) Nozzle 1 09 Cage 1 2B 6.0 mm (1/4”) Nozzle 1 10 O-Ring 1 2C 8.0 mm (5/16) Nozzle 1 11A O-Ring 1 03 Gun Body 1 12 Air Inlet NIpple 1 04 Nut Guide 1 14 Gun Trigger 1 06 Gun Needle 1 15 E-Ring 2 07 O-Ring x2 2 16 Trigger Pin 1 08 Needle Assembly 1 18 Air Fitting 1 8A O-Ring x2 2 19 O-Ring 1 8B Fluid Control Knob Body 1 20 Plastic Hopper 1 8C Washer 1 21 Hopper Clip 1 8D Spr
Inhaltszusammenfassung zur Seite Nr. 13
limited 1 year W arranty Harbor Freight Tools Co. makes every effort to assure that its products meet high quality and durability standards, and warrants to the original purchaser that this product is free from defects in materials and workmanship for the period of one year from the date of purchase (90 days if used by a professional contractor or if used as rental equip- ment). This warranty does not apply to damage due directly or indirectly, to misuse, abuse, negligence or accidents, repa
