Inhaltszusammenfassung zur Seite Nr. 1
model t23092
high-pressure spray gun
oWner's manual
Copyright © ApriL, 2011 By grizzLy industriAL, inC.
Warning: no portion of this manual may be reproduced in any shape
or form Without the Written approval of grizzly industrial, inc.
#ts14062 printed in ChinA
Inhaltszusammenfassung zur Seite Nr. 2
safety for your own safety read instruction manual before operating this equipment t he purpose of safety symbols is to attract your attention to possible hazard- ous conditions. t his manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. t he progression of symbols is described below. r emember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. i
Inhaltszusammenfassung zur Seite Nr. 3
6. use correct air pressure. 13. untrained & unsupervised exceeding the maximum psi rating use. untrained operators are not of this spray gun may cause unpre- aware of the safe use of this spray dictable operation or bursting. gun and may injure themselves or 7. disconnect air pressure cause fire. All untrained operators before servicing, changing accesso- must be directly supervised at all ries, or moving to another location. times if using this spray gun. never leave this spray gun unat-
Inhaltszusammenfassung zur Seite Nr. 4
section 2: introduction f oreword specifications the specifications, details, and photographs type of Feed ...................................siphon in this manual represent the Model h8222 Viscosity range .................Medium to high as supplied when the manual was prepared. Waterborne Material Compatible ........... no h owever, owing to g rizzly’s policy of nozzle size .....................................2.0mm continuous improvement, changes may be Maximum pattern Width ..................
Inhaltszusammenfassung zur Seite Nr. 5
section 3: set up inventory assembly your spray gun was carefully packaged for prior to assembly and use of the spray safe transportation. r emove the packaging gun, it is essential that all parts be thor- materials from around the tool and inspect oughly cleaned and dried. please refer to it. if you discover the spray gun is dam- c leaning on page 10 for more detailed aged, please immediately call Customer instructions. Service at (570) 546-9663 for advice. Make sure all connections ar
Inhaltszusammenfassung zur Seite Nr. 6
identification & c ontrols C B d A e F J g K i h figure 3. Model t23092 identification and controls. r efer to figure 3 and the following f. vacuum relief hose. Allows air to descriptions to gain an understanding of flow into the fluid cup as needed to the features and controls of this spray gun. prevent a vacuum build-up. Be sure to read the entire manual before g. f luid c up l ock l ever. releases/ beginning spraying operation to ensure a engages pressure between the cup safe and effi
Inhaltszusammenfassung zur Seite Nr. 7
section 4: operations t o reduce the risk of injuries from compressed air explosion, always e Xpl osion hazard ! do not disconnect the air line before remov- smoke or have any source of flame ing/installing the fluid cup. or spark near spraying. vapors will explode if ignited. spraying t he Model t 23092 high-pressure spray gun is designed to spray a wide variety of materials such as lacquers, stains, primers, multi-component paints, clear coats, acrylics, epoxies, etc. it is ideal for
Inhaltszusammenfassung zur Seite Nr. 8
3. Move the cup lock lever against the 10. Adjust the fluid control knob to start vacuum hose connection to release the with a low volume of material and keep pressure between the cup hooks and the atomization as low as possible. pin—this will disengage the cup lid from you will need to use a combination of the cup. fluid control, inlet air pressure, air flow control and stroke speed to achieve the 4. Fill the fluid cup with the desired mate- results you want. spray so the material rial,
Inhaltszusammenfassung zur Seite Nr. 9
6" 12" 14. Maintain an even speed when spraying a tomizing c ap and overlap each stroke by 50%. this a djustment will ensure even coverage, as shown in on the left of figure 5. overlapping less than 50%, as shown on the right, t o ensure good spraying results, the atom- may lead to missed spots or streaky izing cap must be correctly orientated for results. the direction of the stroke pattern—either Correct Incorrect horizontal or vertical. s praying in the wrong direction may lead to m
Inhaltszusammenfassung zur Seite Nr. 10
section 5: accessories g 6261—c ampbell h ausfeld™ Water h7274—c ampbell hausfeld™ pressure f ilter r egulator r emove damaging water vapor before Mini s eries. provides regulated output it reaches your spray gun. t his highly pressure of 0 to 125 psi for proper tool effective, five micron filter features a see- operation. Locking pressure knob prevents through bowl and easy in-line connections. accidental adjustments. 15 s CFM flow 1 1 150 psi maximum air pressure. ⁄4" npt . capacity @ 90
Inhaltszusammenfassung zur Seite Nr. 11
section 6: maintenance 3. remove the cup and cup lid, then disassemble the gun by unscrewing the fluid control knob and removing the spring and needle (see figure 13). Atomizing Fluid Control Cap needle Knob t o reduce the risk of injuries from compressed air explosion, always disconnect the air line before per- forming maintenance or service. Fluid nozzle c leaning Cup Lid properly cleaning the spray gun helps to Assembly ensure good spraying results and long gun life. Always thoroughly
Inhaltszusammenfassung zur Seite Nr. 12
5. rinse these parts thoroughly in solvent, l ubrication then dry with compressed air or let air dry. Lubricate the following areas shown in f igure 14 with a non-silicon spray gun lubricant after each cleaning. do not soak the spray gun body in solvent. prolonged exposure to sol- a. Fluid Control Knob vent will rapidly deteriorate the spray b. pattern Control gun washers and seals. c. Air Valve packing d. Atomizing Cap threads note: If the small holes in the atom- e. trigger pin izing ca
Inhaltszusammenfassung zur Seite Nr. 13
section 7: service t roubleshooting symptom possible cause solution Fluttering or spit- 1. dry or worn fluid nozzle seat 1. tighten fluid tip or replace ting spray. permits air to seep into fluid seat with new one. passage. 2. Material level too low. 2. Add material. 3. Fluid nozzle obstructed. 3. Clean. 4. dry needle packing. 4. Lubricate needle. u neven top or bot- 1. Atomizing cap holes are 1. Clear holes. tom pattern. obstructed. 2. Build-up on top or bottom of 2. Clean. fluid nozzle. 3. Bu
Inhaltszusammenfassung zur Seite Nr. 14
symptom possible cause solution n o spray output. 1. no pressure at gun. 1. Check air supply. 2. Fluid passages dirty. 2. Clean gun, remove any obstructions. 3. Fluid control closed. 3. open. 4. out of paint. 4. refill. 5. Material too thick. 5. thin to manufacturer's rec- ommendations. excessive over- 1. Fluid pressure too high. 1. reduce fluid pressure. spray. 2. gun is too far from surface. 2. Keep gun at recommended distance. 3. spraying too fast. 3. s low down and maintain consistent, ev
Inhaltszusammenfassung zur Seite Nr. 15
t 23092 parts breakdown Parts breakdown provided for reference only. Not all parts shown are available for purchase. 17 33 15 18 39 34 36 35 19 16 14 15 13 12 20 23 25 22 21 38 11 10 37 39 24 4 8 9 40 7 5 6 32 31 41 29 30 28 26 27 3 42 2 1 43 44 45 REF PART # DESCRIPTION REF PART # DESCRIPTION 1 N/A AIR INLET CONNECTOR 1/4" NPT 24 N/A WASHER 2 N/A SCREW 25 N/A DIRECTION SCREW 3 N/A GUN BODY 26 N/A TRIGGER COMPRESSION SPRING 4 N/A NEEDLE HOUSING 27 N/A TRIGGER STEM 5 N/A FLUID ADJUSTMENT NEEDLE
Inhaltszusammenfassung zur Seite Nr. 16
Warranty Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse, negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty and any and all warranties that may be implied by law, including any merchantability or fitness, for any par- ticular purpose, are hereby limited to the duratio
