Inhaltszusammenfassung zur Seite Nr. 1
MODEL G0605X1/G0606X1/
G0696X/G0697X/
12" LEFT TILTING TABLE SAW
OWNER'S MANUAL
Model G0697X
Model G0606X1
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
Inhaltszusammenfassung zur Seite Nr. 2
Inhaltszusammenfassung zur Seite Nr. 3
Table of Contents INTRODUCTION ............................................... 2 SECTION 5: SHOP MADE SAFETY ACCESSORIES .............................................. 50 SECTION 1: SAFETY ....................................... 5 SECTION 6: AFTERMARKET ACCESSORIES FROM GRIZZLY ............................................. 58 SECTION 7: MAINTENANCE ......................... 60 SECTION 2: POWER SUPPLY ..............
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Manual Accuracy Contact Info your machine may not exactly match the manual Machine Description www.grizzly.com
Inhaltszusammenfassung zur Seite Nr. 5
Identification Figure 1. To reduce the risk of For Your Own Safety Read Instruction serious injury when using Manual Before Operating Saw this machine, read and a) Wear eye protection. understand this entire b) Use saw-blade guard and spreader for manual before beginning every operation for which it can be used, any operations. including all through sawing. c) Keep hands out of the line of saw blade. d) Use a push-stick when required. e
Inhaltszusammenfassung zur Seite Nr. 6
MODEL G0605X1/G0606X1/G0696X/G0697X 12" LEFT-TILTING TABLE SAWS G0605X1 G0606X1 G0696X G0697X Model Number Motor Required Power Supply Circuit Speed Power Requirement Full Load Current Rating Plug/Outlet Type (Recommended) Table Size (full assembly) Table Height Above Floor Overall Machine Size Footprint Size Weight
Inhaltszusammenfassung zur Seite Nr. 7
SECTION 1: SAFETY For Your Own Safety, Read Instruction Manual Before Operating this Machine The purpose of safety symbols is to attract your attention to possible hazardous conditions. This manual uses a series of symbols and signal words intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indicat
Inhaltszusammenfassung zur Seite Nr. 8
DISCONNECTING POWER SUPPLY. FORCING MACHINERY. GUARDS & COVERS. APPROVED OPERATION. NEVER STAND ON MACHINE. STABLE MACHINE. DANGEROUS ENVIRONMENTS. AWKWARD POSITIONS. ONLY USE AS INTENDED. USE RECOMMENDED ACCESSORIES. UNATTENDED OPERATION.
Inhaltszusammenfassung zur Seite Nr. 9
Additional Safety for Table Saws HAND POSITIONING. FENCE. PUSH STICKS/BLOCKS. BLADE GUARD. CUT-OFF PIECES. OFF BLADE ADJUSTMENTS. RIVING KNIFE. OFF CHANGING BLADES. DAMAGED SA
Inhaltszusammenfassung zur Seite Nr. 10
Preventing Kickback Take the precautions below to avoid the most common causes of kickback: Statistics show that most common acci- dents among table saw users can be linked to kickback. Kickback is typically defined as the high-speed expulsion of stock from the table saw toward its opera- tor. In addition to the danger of the opera- tor or others in the area being struck
Inhaltszusammenfassung zur Seite Nr. 11
Glossary of Terms VERY ARBOR: PARALLEL: BEVEL EDGE CUT: PERPENDICULAR: Page 42 BLADE GUARD ASSEMBLY: PUSH STICK: Page 35 Page 53 RABBET: CROSSCUT: Page 45 Page 41 RIP CUT: DADO BLADE: Page 40 RIVING KNIFE: DADO CUT: Page 38 Page 42 SPREADER: FEATHERBOARD: Page 50 STRAIGHTEDGE: KERF: THIN KERF BLADE: KICKBAC
Inhaltszusammenfassung zur Seite Nr. 12
SECTION 2: POWER SUPPLY Availability Circuit Information For your own safety and protection of property, consult a qualified electrician if you are unsure about wiring practices or electrical codes in your area. Electrocution, fire, or equipment damage may occur if machine is not Note: The circuit requirements listed in this man- correctly grounded and ual apply to a dedicated circuit—where only one connected to the
Inhaltszusammenfassung zur Seite Nr. 13
Model G0606X1/G0697X Model G0606X1/G0697X Circuit Requirements for 440V Connection Device For 220V operation: Voltage Conversion Nominal Voltage .............................. 440V/480V Cycle ..........................................................60 Hz Phase .................................................... 3-Phase Circuit Rating ...................................... 15 Amps Connection ......Hardwire with Locking Switch GROUNDED
Inhaltszusammenfassung zur Seite Nr. 14
Grounding Instructions Correcting Phase Polarity To correct wiring that is out of phase: 1. Extension Cords (220V Only) 2. Figure 5. Minimum Gauge Size ...........................10 AWG Figure 5 Maximum Length (Shorte
Inhaltszusammenfassung zur Seite Nr. 15
4. Figure 7 Voltage Conversion Figure 7. NOTICE Refer to the motor junction box cover dia- gram for motor connection locations and 5. voltage conversion. If not present, use the instructions below, or call our Tech Support Figure 8 Department at (570) 546-9663. Page 80 Page 82 Converting Model G0606X1/G0697X to 440V 1. 2. Figure 6 Figure 8. 6. Figure 9
Inhaltszusammenfassung zur Seite Nr. 16
SECTION 3: SETUP Needed for Setup This machine presents serious injury hazards to untrained users. Read through this entire manu- al to become familiar with Description Qty the controls and opera- tions before starting the machine! Wear safety glasses dur- ing the entire setup pro- cess! This machine and its com- ponents are very heavy. Get lifting help or use power lifting equipment such as a forklift to move heavy i
Inhaltszusammenfassung zur Seite Nr. 17
Fence Inventory G0605X1/G0606X1 Box Contents (Figure 12) Qty A. Inventory B. Table Saw Unit Box Contents (Figure 10 & 11) Qty A. B. C. D. E. Figure 12. F. G. Fence Rail Inventory H. I. Box Contents (Figure 13) Qty A. B. C. Figure 13. Figure 10. Hardware and Tools (Not Shown): Qty J. Figure 11.
Inhaltszusammenfassung zur Seite Nr. 18
Extension Table Inventory Outfeed Table Inventory Box Contents (Figure 14) Qty Box Contents (Figure 15) Qty A. A. B. B. C. C. D. D. E. E. Hardware and Tools (Not Shown): Qty Hardware and Tools (Not Shown): Qty
Inhaltszusammenfassung zur Seite Nr. 19
Fence Box Contents (Figure 19) Qty A. B. Figure 16. Figure 19. Fence Rail Inventory Box Contents (Figure 20) Qty A. B. C. Figure 17. Figure 18. Figure 20. Hardware and Tools (Not Shown): Qty Hardware and Tools (Not Shown): Qty
Inhaltszusammenfassung zur Seite Nr. 20
Hardware Recognition Chart
