Inhaltszusammenfassung zur Seite Nr. 1
MODEL H8222
SPRAY GUN
INSTRUCTION MANUAL
COPYRIGHT © AUGUST, 2007 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#TR9786 PRINTED IN CHINA
Inhaltszusammenfassung zur Seite Nr. 2
SAFETY For Your Own Safety Read Instruction Manual Before Operating This Equipment The purpose of safety symbols is to attract your attention to possible hazard- ous conditions. This manual uses a series of symbols and signal words which are intended to convey the level of importance of the safety messages. The progression of symbols is described below. Remember that safety messages by themselves do not eliminate danger and are not a substitute for proper accident prevention measures. Indic
Inhaltszusammenfassung zur Seite Nr. 3
6. USE CORRECT AIR PRESSURE. 13. UNTRAINED & UNSUPERVISED Exceeding the maximum PSI rating USE. Untrained operators are not of this spray gun may cause unpre- aware of the safe use of this spray dictable operation or bursting. gun and may injure themselves or 7. DISCONNECT AIR PRESSURE cause fire. All untrained operators before servicing, changing accesso- must be directly supervised at all ries, or moving to another location. times if using this spray gun. 14. READ MATERIAL LABELS Never
Inhaltszusammenfassung zur Seite Nr. 4
INTRODUCTION Foreword Specifications The specifications, details, and photographs Cup Size ..........................................1000cc in this manual represent the Model H8222 Feed Type ....................................... Siphon as supplied when the manual was prepared. Fluid Tip Size ................................... 2.0mm However, owing to Grizzly’s policy of Air Consumption .................... 4.2–7.1 CFM continuous improvement, changes may be Operating Pressure Range ........ 45–
Inhaltszusammenfassung zur Seite Nr. 5
SETUP Setup Inventory Before assembling and using the spray gun, Your spray gun left our warehouse in a thoroughly clean and dry all parts. Please carefully packed box. If you discover the refer to Cleaning in the MAINTENANCE spray gun is damaged after you have section on Page 10 for more detailed signed for delivery, please immediately instructions. Make sure all connections are call Customer Service at (570) 546-9663 tight enough to prevent air leaks but not so for advice. tight as
Inhaltszusammenfassung zur Seite Nr. 6
Cup Removal & Installation Controls The cup is removed/installed by loosen- ing/tighting the cup lock cover and engag- ing/disengaging the cup pins in the cup Pattern Control Atomizing Cap cover groove (see Figure 4). Cup Lock Cover Fluid Control Trigger Cup Pin (1 of 3) Air Flow Control Figure 4. Installing cup. Cup Figure 3. Controls. 1. Fluid Control: Controls the volume of material that travels through the fluid tip. 2. Pattern Control: Adjusts the spray pattern from a round pattern t
Inhaltszusammenfassung zur Seite Nr. 7
OPERATIONS Spraying The Model H8222 siphon feed spray gun set is designed to spray a wide variety of materials such as lacquers, stains, prim- ers, multi-component paints, clear coats, acrylics, epoxies etc. It is ideal for auto EXPLOSION HAZARD! body and woodworking projects. DO NOT smoke or have any source of flame or spark near spraying. To use your spray gun: Vapors will explode if ignited. 1. Read and follow the material manufac- turer's instructions for spraying, mixing, safety, disp
Inhaltszusammenfassung zur Seite Nr. 8
7. Adjust the fluid control knob to start 10. Begin spraying 2-3 inches before the with a low volume of material and keep work and continue to the end of the the atomization as low as possible. work. Continue the motion for a few You will need to use a combination of inches past the work until you are fluid control, inlet air pressure, air flow ready for the return stroke. control and stroke speed to achieve the results you want. Spray so the material 11. Maintain an even speed when spray
Inhaltszusammenfassung zur Seite Nr. 9
Atomizing Cap and Pattern Fan Adjustments The atomizing cap can be adjusted for horizontal or vertical spraying patterns. Spraying in the wrong direction may lead Stroke to material build up on the atomizing cap horn. Many performance problems are caused by clogged atomizing holes on the Figure 8. Set up for horizontal spray stroke atomizing cap horns (see Cleaning on with vertical fan pattern. Page 10). Rotating the pattern adjustment knob (see Figure 3) changes the shape of the spray
Inhaltszusammenfassung zur Seite Nr. 10
ACCESSORIES H7274—Campbell Hausfeld™ Pressure G6261—Campbell Hausfeld™ Water Regulator Filter Since PSI drops through lengths of air Filtering out water and oil before it reaches hose, attaching a regulator directly to the the spray gun is critical for high quality spray gun ensures accurate air regulation spraying results. This filter is rated at 150 1 for the best results possible. Provides PSI maximum air pressure, and has a ⁄4" regulated output pressure of 0 to 125 PSI NPT air inl
Inhaltszusammenfassung zur Seite Nr. 11
MAINTENANCE 5. Unscrew the atomizing cap and the Cleaning fluid tip. The fully disassembled gun should look like Figure 14. Proper cleaning is the best way to ensure 6. Rinse all parts thoroughly in solvent, trouble free performance from your spray then dry with compressed air or let gun. If your gun is not thoroughly cleaned, air dry. Try not to expose O-rings to damage and poor spraying will result. solvent or they may get damaged. Problems caused by improper cleaning will not be cov
Inhaltszusammenfassung zur Seite Nr. 12
Lubrication D B A E Lubricate the following areas with a non- silicon spray gun lubricant after cleaning. A. Atomizing Cap Threads C B. Air Valve Packing C. Trigger Pin D. Pattern Control E. Fluid Control Knob E F. Air Flow Control Knob Allow the lubricant to coat threads, and run into gun body to lubricate all moving parts and seals. Figure 15. General lubrication points. Model H8222 Spray Gun -11-
Inhaltszusammenfassung zur Seite Nr. 13
Troubleshooting Symptom Possible Cause Solution Fluttering or spitting 1. Dry or worn fluid tip seat per- 1. Tighten fluid tip or replace spray. mits air to seep into fluid pas- seat with new one. sage. 2. Material level too low. 2. Add material. 3. Fluid tip or filter obstructed. 3. Clean. 4. Dry needle packing. 4. Lubricate needle. Uneven top or bot- 1. Atomizing cap holes are 1. Clear holes. tom pattern. obstructed. 2. Build-up on top or bottom of 2. Clean. fluid tip. 3. Build-up on atomizin
Inhaltszusammenfassung zur Seite Nr. 14
Symptom Possible Cause Solution Excessive over- 1. Fluid pressure too high. 1. Reduce fluid pressure. spray. 2. Gun is too far from surface. 2. Keep gun at recommended distance. 3. Spraying too fast. 3. Slow down and maintain consistent, even parallel stroke. Unable to control 1. Pattern adjustment screw is 1. Clean or replace. spray fan. not seating properly. 2. Atomizing cap is loose. 2. Tighten atomizing cap. Runs and sags. 1. Damaged seal. 1. Replace damaged seals. Material leaks from 1.
Inhaltszusammenfassung zur Seite Nr. 15
Parts Breakdown H8222 �� �� �� �� �� �� �� �� �� � �� �� � �� �� �� �� �� �� �� �� �� �� � �� �� �� �� �� �� �� �� �� �� �� � �� � �� � �� � � �� �� � � � REF PART # DESCRIPTION REF PART # DESCRIPTION 1 PH8222001 ADJUSTMENT SCREW 24 PH8222024 NEEDLE GASKET 2 PH8222002 ADJUSTMENT KNOB 25 PH8222025 SEALING WASHER 3 PORS004 O-RING 3.5 X 1.5 S4 26 PH8222026 DIRECTION SCREW 4 PH8222004 FLAT WASHER 3.5MM 27 PH8222027 NOZZLE 5 PH8222005 COMPRESSION SPRING 28 PH8222028 AIR CAP 6 PH8222006 AIR VALVE TUBE
Inhaltszusammenfassung zur Seite Nr. 16
