Inhaltszusammenfassung zur Seite Nr. 1
STIGA PARK
4WD
92 M
107 M
107 M HD
121 M
110 Combi Pro
125 Combi Pro
8211-0543-03
Inhaltszusammenfassung zur Seite Nr. 2
110/125 Combi Pro 2 1 125 Combi Pro 1 2 3 4 110/125 Combi Pro 121 M 107 M HD 110/125 Combi Pro B 107 M HD C B A 121 M 5 110/125 Combi Pro 6 110/125 Combi Pro Torx T30 E F Torx T30 7 121 M 8 121 M G H I 10 mm 10 mm 2
Inhaltszusammenfassung zur Seite Nr. 3
10 92/107 9 92/107 13 mm 13 mm 10 mm 92/107 M 12 92/107 M 11 B D B A J K L 14 110/125 Combi Pro 13 107 M HD 15 16 M 3
Inhaltszusammenfassung zur Seite Nr. 4
18 17 92/107 M 107 M HD 121 M 5 mm 20 110/125 Combi Pro 19 1/3 21 92/107 M 22 107 M HD 23 24 121 M 4
Inhaltszusammenfassung zur Seite Nr. 5
25 26 107 M HD 110/125 Combi Pro O O N 27 28 125 Combi Pro 92/107 M 107 M HD 121 M 24 Nm P 24 Nm 24 Nm Q 9,8 Nm 30 29 110 Combi Pro 45 Nm 5
Inhaltszusammenfassung zur Seite Nr. 6
EN ENGLISH 1 GENERAL 2 DESCRIPTION This symbol indicates WARNING. Seri- 2.1 General ous personal injury and/or damage to The cutting deck is intended for use on Stiga’s 4- property may result if the instructions wheel drive Park machines. are not followed carefully. The cutting deck is supplied in one of the follow- You must read these instructions for use ing versions: and the machine’s safety instructions • With manual adjustment of cutting height. carefully. • With electrical adjustment
Inhaltszusammenfassung zur Seite Nr. 7
EN ENGLISH 2.3.3 Rear mounting 3 ASSEMBLY The cutting deck’s rear section is secured with the pins in fig. 13. 3.1 Installing the 110/125 Combi Pro 1. Place the cutting deck in position in front of the 2.4 Controls, 92/107 M machine. 2.4.1 Cutting height adjustment 2. Install the following components on both wheel The cutting height can be adjusted between 30 and axles: 85 mm. • Washer (3:B). The setting can be adjusted to a number of fixed • Deck mount (3:C). positions using the lever. Se
Inhaltszusammenfassung zur Seite Nr. 8
EN ENGLISH 3.2 Installation of 107 M HD, 121 M 3.3 Installing 92/107 M 1. Place the cutting deck in position in front of the 1. Place the cutting deck in position in front of the machine. machine. 2. Install the following components on both wheel 2. Install the following components on both wheel axles: axles: • Washer (3:B). • Washer (11:B). • Deck mount (3:C). • Deck arm (11:D). • Washer (3:B). • Washer (11:B). • Circlip (3:A). • Circlip (11:A). 3. Remove the pins on both sides. See fig. 7:I
Inhaltszusammenfassung zur Seite Nr. 9
EN ENGLISH 3.5.2 Basic setting, 92/107 M, 121 M 4.2.2 Incline See fig. 17 and perform basic setting of 92/107 M When the cutting deck is inclined forwards, the and 121 M as follows: “Multiclip” effect is reduced while the cut grass is dispersed better. 1. Place the machine on a level floor. Requirements for floor flatness: ±1 mm/m. No Inclining forwards is recommended for thicker slope towards a floor drain or similar may occur grass. in front of or behind the machine. 4.3 Mowing advice 2. T
Inhaltszusammenfassung zur Seite Nr. 10
EN ENGLISH 92/107 M: Lift up the rear section of the cutting deck, undo the catches (12:L) and lower. 5 MAINTENANCE 121 M: Disconnect the rear section of the cut- ting deck by removing the pins (7:I). 5.1 Preparation 6. Remove the belt cover. See fig. 5:E, 8 and 10. All service and all maintenance must be carried out The number in the figure indicates the key on a stationary machine with the engine switched width. off. 7. Only 110/125 Combi Pro: Prevent the machine from rolling by al- Rem
Inhaltszusammenfassung zur Seite Nr. 11
EN ENGLISH 5.6.1 Separate blades 6 SPARE PARTS The blades are replaceable. When replacing, both blades on the same blade bar must be replaced to STIGA genuine spare parts and accessories are de- avoid imbalance. signed specifically for STIGA machines. Please Tightening torque: note that ‘non-genuine’ spare parts and accessories Screws (27:P) - 24 Nm have not been checked or approved by STIGA: Shear bolts (27:Q) - 9.8 Nm The use of such parts and accessories In the event of a collision, the
Inhaltszusammenfassung zur Seite Nr. 12
www.stiga.com GGP Sweden AB · Box 1006 · SE-573 28 TRANÅS
