Inhaltszusammenfassung zur Seite Nr. 1
E
z
z
0
-I
m
0 C
C 0
Cb
m
r
0
z
(0
Cb)
N
w
0
0
C’)
0
Inhaltszusammenfassung zur Seite Nr. 2
___________________ POLARIZED PLUG CAUTION To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. if the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way. SEWING MACHINE Record in space provided below the Serial No. and Model No. of this appliance. The Serial
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY INSTRUCTIONS When using an electrical appliance, basic safety precautions should always be llowed, including the following: before using (this Read all instructions ippliance). reduce the risk of electric shock: DANGER——To kn appliance should never be left unattended when plugged in. Always unplug this pliance from the electric outlet immediately after using and before cleaning. WARNING——To reduce the risk of burns, fire, lectric shock, or injury to persons: Do not allow to be u
Inhaltszusammenfassung zur Seite Nr. 4
SAVE fingers Special care around the sewing needle. machine use the proper needle The can the needle cause use bent needles. push the needle causing break. sewing machine adjustments the needle (‘0”) area, such as threading needle, changing needle, threading changing presser machine the covers, other user when adjustments mentioned the manual. where operate a surface such as bed couch the openings THESE WARNING Keep away from moving parts. required 2. Always plate. wrong plate to break. not 4. n
Inhaltszusammenfassung zur Seite Nr. 5
. NAMES PARTS SEWING or SEWING 8 Lifter 9 of SEWING Zigzag Zigzag MAKING BUTTONHOLES Left BUTTONS SEWING OVERCASTING OVERLOCKING 9. Elastic of Fun STITCH Elastic Hem SEAM STRETCH SEWING 2. 3. STITCHING TUCKING 4. 5. 41 6. MENDING 8. WORK 9. EMBROIDERY MAINTENANCE 0. TROUBLE CHART Light Bulb 2 I. OF 3 BEFORE 5 6 7 8 2 Up 6 Dial Dial 8 21 5. ZIGZAG 6. of ON 7. 8. of 31 of of HEM BLIND Blind 1. SHELL PIN QUILTING 7. a Rip Oiling 1. CONTENTS I.. . . 3. Pattern Stretch Patterns Connecting Power Inser
Inhaltszusammenfassung zur Seite Nr. 6
\ N) - N) N) N) N) — cç ( 4 w 0 a N) 0 CD N) N) N) (A) N) N) N) N) 0) 01 (A) (Il 0) CD 0 CO
Inhaltszusammenfassung zur Seite Nr. 7
PARTS 1. NAMES OF bobbin winding 1. Thread guide for Pressure regulator 2. lever 3. Take-up 4. Face cover tension dial 5. Upper thread for upper threading 6. Thread guide thumb screw 7. Presser foot 8. Presser foot 9. Free arm 10. Shuttle cover 11. Spool pins dial 12. Pattern selection dial 13. Stitch length control 14. Needle position 15. sewing lever Reverse 1 Zigzag width control 6. lever 1 Drop feed 7. spindle Bobbin winding 1 8. Bobbin winding stopper 1 9. Handwheel 20. Stop motion knob 21.
Inhaltszusammenfassung zur Seite Nr. 8
C, C) m Cl) Cl) I 0 p L m a, N a, C-) 0 C Cl) C •0 0 0 0 CD :7 0 CO CO U) C 0 CD 0 CD 0 0. CD C CD 0 0 C) CD CD 0 0 CD 0 (A) C) C) CD U) U) 0 a 0 - a CD iii 0 a liii CD 0 [fi CD U) 2: CIA 0 CIA CD CD - u 2: 0 CD U) 0 C, — — z - CD CD CD CD C) x 0 •0 ) C) C) — 3• CD U) CD —U) U) U) 0 0) CD
Inhaltszusammenfassung zur Seite Nr. 9
Detachable 3. BEFORE SEWING Extension Table Machine stored flat-bed which makes your work easier ordinary sewing. off table and the machine used free-arm model. Free-arm convenient sew embroider; trousers, T-shirts, blouses, etc. vice-versa above steps attach extension table. open accessory open, as illustrated. style Slide as to or cuffs sleeves, of of to To of box, push is is a is Do it in in lid
Inhaltszusammenfassung zur Seite Nr. 10
D controller and Connect foot power cord your plugging machine, sure that voltage same that your machine. (written plate at back machine) Switch put the ® power and turn sewing machine the Push button to turn sewing on and switch or machine when not vary from *Specifications country country. The more press the faster the machine Before be as of on of on on on light. light off. Always off unplug use. to you foot controller, runs. (. is a in in I Connecting foot controller power cord and b
Inhaltszusammenfassung zur Seite Nr. 11
Needle Changing stopper ® Set needle the highest position turning handwheel towards Loosen needle clamp screw and remove needle. With flat away from face insert new needle groove needle bar. Push needle reaches and tighten needle clamp screw needle use straight Proper sharp point. straight sharp worn needles defective or skipping, not causes stitch snapping needles breakage also can damage thread; hook and needle plate. by you. you, into of until firmly. with Always needle shaft point Using only
Inhaltszusammenfassung zur Seite Nr. 12
\ , Changing Foot Raise lifter presser foot 1; in highest Set needle the position turning handwheel by ‘). towards you 4 Snap-on Presser Foot: a Push the lever in the arrow direction so that the presser foot will come off. F Position a new foot with the pin right under the groove of the b holder. the presser foot lifter so Lower the foot will be automatically that snapped on. — When you fail to catch the foot, push the lever in the arrow direction slightly. ‘,— —7—
Inhaltszusammenfassung zur Seite Nr. 13
Winding Bobbin needle in the highest position Set turning handwheel towards by you. Open shuttle cover. latch of bobbin case and Open it out. take of bobbin case and Close latch comes out easily. bobbin —8—
Inhaltszusammenfassung zur Seite Nr. 14
handle. back and spool spool and device, tension ers and around clockwise several bobbin times. spindle. bobbin to handwheel hand handwheel unscrewing thread through thread numb thread disengage stop pre gh’N . Push to fold Pull out pin felt put a on pin. Put a spool on spool pin. Draw from spool pin guide following N Wind Push on (‘b Holding with your left by motion knob. —9—
Inhaltszusammenfassung zur Seite Nr. 15
Push bobbin to right and press down foot controller. Machine stops automatically when bobbin is full. Push bobbin left, to to disengage from wheel. Take off bobbin from spindle and cut thread. Retighten stop motion knob. If bobbin is wound unevenly as shown, open face cover and trou e loosen set-screw of the guide for bobbin winding: Use screw driver to adjust height. correction I —10—
Inhaltszusammenfassung zur Seite Nr. 16
Inserting Bobbin Place bobbin in its case with thread running in direction of arrow. Guide thread into slot of 4 ® bobbin case. } Pulling thread to left, bring it under tension spring then to delivery eye ®. —1 1—
Inhaltszusammenfassung zur Seite Nr. 17
Adjusting Lower Tension To test bobbin tension, hang and shake bobbin case as shown. At proper tension bobbin case will gradually drop a small amount. To adjust tension, turn adjusting screw with small screwdriver. } Raise needle in the highest position. Leave end of thread of about 10 cm (4”) from bobbin case. Take hold of latch and push bobbin case into shuttle Release latch when bobbin case is fully inserted. DROP FEED LEVER The lever is in the right side of shuttlecover. Fornormal sewing, mo
Inhaltszusammenfassung zur Seite Nr. 18
Threading Upper Thread Raise presser foot lifter. Raise take-up lever to the highest position by turning handwheel towards you. Thread following numbers 1D-). Pass thread through guide L. of tension Lead thread either side disc D. Hook it to guide from down ® to upwards. Thread take-up lever ®. right Pass thread to guide from ® one) to left, and guide (left then needle eye 1 Leave end of thread of about 5 cm (6”). —13—
Inhaltszusammenfassung zur Seite Nr. 19
Twin Needle Threading Thread in the same way as normal threading, except at points and ©, © threads At point (, pass sepa tension ratly to right and left of disc. At guide of pass one threads ©, right guide to and the other at left guide. At point (, thread from right guide should be lead to right needle eye, and from left guide to left needle eye. Leave ends of threads of about 15 cm (6”). —I Decorative Tucks or Designs Any stitch can be used with the twin needle for decorative effects. Most at
Inhaltszusammenfassung zur Seite Nr. 20
Drawing Up Lower Thread Hold end of upper thread with left hand. Turn handwheel slowly towards you until needle moves down and up again. Pull upper thread slowly and lower thread will be brought up in a loop. 1 Pull out both threads to about 5 cm (6”) and place them together left. under presser foot on Foot Pressure Push down the outer ring of the pressure regulator. This will re lease the pressure on the presser foot. To increase the pressure, push down inner pin until suitable pressure is obta
