Bedienungsanleitung Porter-Cable PTS6

Inhaltszusammenfassung zur Seite Nr. 1

ESPAÑOL: PÁGINA 11
Instruction manual
FRANÇAIS: PAGE 19
Manual de
Random Orbital Palm Sanders
Instrucciones
Guide d'utilisation Lijadora Orbital para la Palma
de la Mano
Ponceuse orbitale aléatoire
MODEL/
MODELO/
MODÈLE
PTS3
PTS4
PTS5
PTS6
PTS7
PTS8
PTS9
To learn more about Porter-Cable visit
PTS10
our website at:
http://www.porter-cable.com
IMPORTANT
Para obtener más información sobre
Please make certain that the person who is
Porter-Cable, visite nuestro sitio web en:
to use this equipment c

Inhaltszusammenfassung zur Seite Nr. 2

Inhaltszusammenfassung zur Seite Nr. 3

HAZARD RISK OF LOSS OF HEARING WHAT COULD HAPPEN HOW TO PREVENT IT  Long term exposure to noise produced from the opera-  Always wear ANSI S3.19 hearing protection. tion of air tools can lead to permanent hearing loss. HAZARD RISK TO BREATHING INHALATION HAZARD WHAT COULD HAPPEN HOW TO PREVENT IT  Abrasive tools, such as grinders, sanders, and cut-off  Always wear MSHA/NIOSH approved, properly fitting tools generate dust and abrasive materials which can face mask or respirator when using suc

Inhaltszusammenfassung zur Seite Nr. 4

HAZARD RISK OF INJURY (continued) WHAT COULD HAPPEN HOW TO PREVENT IT  Improperly maintained tools and accessories can cause  Maintain the tool with care. serious injury.  Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control.  There is a risk of bursting if the tool is damaged.  Check for misalignment or binding of moving parts, breakage of parts, and any other condition that affects the tool’s operati

Inhaltszusammenfassung zur Seite Nr. 5

SPECIFICATIONS NOTE: All models come standard with a *PSA type sander pad. Model # Orbit Pad Vacuum Max RPM Spindle Air Inlet Size Operating (Free Thread Pressure Speed) PTS3 3/16" 5" No 90 psig 12000 5/16-24 1/4-18 NPT Female Female PTS4 3/16" 5" Yes 90 psig 12000 5/16-24 1/4-18 NPT Female Female PTS5 3/32" 5" No 90 psig 12000 5/16-24 1/4-18 NPT Female Female PTS6 3/32" 5" Yes 90 psig 12000 5/16-24 1/4-18 NPT Female Female PTS7 3/16" 6" No 90 psig 12000 5/16-24 1/4-18 NPT Female Female PTS8 3

Inhaltszusammenfassung zur Seite Nr. 6

ASSEMBLY IMPORTANT: Line pressure or hose inside diameter should be increased to compensate for unusually long air hoses (over 25 feet). Minimum hose diameter should be 3/8” I.D. and fittings should have 1/4” NPT thread. OPERATION Before each use: ● Drain water from air compressor tank and condensation from air lines. See air compressor’s operators manual. Disconnect the tool from the air supply before lubricating or changing abrasive disc. ● Lubricate tool, see “Maintenance” section in this ma

Inhaltszusammenfassung zur Seite Nr. 7

Inhaltszusammenfassung zur Seite Nr. 8

Lubrication Air tools require lubrication throughout the life of the tool. The air motor and bearing uses com- pressed air to power the tool. Because moisture in compressed air will rust the air motor, you must lubricate the motor daily. An inline oiler is recommended. To lubricate the air motor manually: ● Disconnect the tool from the air supply holding it so the air inlet faces up. ● Depress the trigger and place one to two drops of air tool oil in the air inlet Depressing the trigger helps ci

Inhaltszusammenfassung zur Seite Nr. 9

NOTES 9- ENG D29847

Inhaltszusammenfassung zur Seite Nr. 10

LIMITED WARRANTY PORTER-CABLE CORPORATION warrants to the original purchaser that all products covered under this warranty are free from defects in material and workmanship. Products covered under this warranty include air compressors, air tools, service parts, pressure washers, and generators, which have the following warranty periods: 3 YEARS - Limited warranty on 2-stage oil-free air compressor pumps that operate at 1725 RPM. 2 YEARS - Limited warranty on oil-lubricated air compressor pumps.