Bedienungsanleitung Clarke 07111A

Bedienungsanleitung für das Gerät Clarke 07111A

Gerät: Clarke 07111A
Kategorie: Schleifmaschine
Produzent: Clarke
Größe: 0.88 MB
Datum des Hinzufügens: 10/24/2014
Seitenanzahl: 74
Anleitung drucken

Herunterladen

Wie kann man es nutzen?

Unser Ziel ist Ihnen einen schnellen Zugang zu Inhalten in Bedienungsanleitungen zum Gerät Clarke 07111A zu garantieren. Wenn Sie eine Online-Ansicht nutzten, können Sie den Inhaltsverzeichnis schnell durchschauen und direkt zu der Seite gelangen, auf der Sie die Lösung zu Ihrem Problem mit Clarke 07111A finden.

Für Ihre Bequemlichkeit

Wenn das direkte Durchschauen der Anleitung Clarke 07111A auf unserer Seite für Sie unbequem ist, können sie die folgende zwei Möglichkeiten nutzen:

  • Vollbildsuche – Um bequem die Anleitung durchzusuchen (ohne sie auf den Computer herunterzuladen) können Sie den Vollbildsuchmodus nutzen. Um das Durchschauen der Anleitung Clarke 07111A im Vollbildmodus zu starten, nutzen Sie die Schaltfläche Vollbild
  • Auf Computer herunterladen – Sie können die Anleitung Clarke 07111A auch auf Ihren Computer herunterladen und sie in Ihren Sammlungen aufbewahren. Wenn Sie jedoch keinen Platz auf Ihrem Gerät verschwenden möchten, können Sie sie immer auf ManualsBase herunterladen.
Clarke 07111A Handbuch - Online PDF
Advertisement
« Page 1 of 74 »
Advertisement
Druckversion

Viele Personen lesen lieber Dokumente nicht am Bildschirm, sondern in gedruckter Version. Eine Druckoption der Anleitung wurde ebenfalls durchdacht, und Sie können Sie nutzen, indem Sie den Link klicken, der sich oben befindet - Anleitung drucken. Sie müssen nicht die ganze Clarke 07111A Anleitung drucken, sondern nur die Seiten, die Sie brauchen. Schätzen Sie das Papier.

Zusammenfassungen

Unten finden Sie Trailer des Inhalts, der sich auf den nächsten Anleitungsseiten zu Clarke 07111A befindet. Wenn Sie den Seiteninhalt der nächsten Seiten schnell durchschauen möchten, können Sie sie nutzen.

Inhaltszusammenfassungen
Inhaltszusammenfassung zur Seite Nr. 1

FloorCrafter
Belt Sander
Operator's Manual
Manual del operador
Manuel de l’utilisateur
U.S. Patent No. 5,575,710 and No. 6,578,858
READ THIS BOOK EN
English (2 - 20)
ES
LEA ESTE MANUAL Español (22 - 40)
FR
Français (42 - 60)
LISEZ CE MANUEL
This book has important information for the use and safe operation of this machine. Failure to read this
book prior to operating or attempting any service or maintenance procedure to your Clarke American
Sanders machine could result in injury to you or to

Inhaltszusammenfassung zur Seite Nr. 2

ENGLISH EN Table of Contents Operator Safety Instructions ............................................................................. 3 Introduction and Machine Specifications........................................................... 5 230V Electrical Connection Instructions ........................................................... 6 How to Transport the Machine .......................................................................... 7 One Person ..........................................

Inhaltszusammenfassung zur Seite Nr. 3

ENGLISH EN OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA DANGER means: Severe bodily injury or death can occur to you or other personnel if the DAN- GER statements found on this machine or in this Operator's Manual are ignored or are not adhered to. Read and observe all DANGER statements found in this Operator's Manual and on your machine. WARNING means: Injury can occur to you or to other personnel if the WARNING statements found on your machine or in this Operator's Manual ar

Inhaltszusammenfassung zur Seite Nr. 4

ENGLISH EN DANGER: Operating partially assembled sanding equipment could result in injury to the operator or bystander and could cause damage to the equipment or to other property. � Do not operate this equipment unless it it fully assembled and all guards, doors and covers are secured. � Keep all fasteners tight. � Keep all adjustments within manufacturers specifications. DANGER: Moving parts on this sanding equipment can cause injury to the operator or bystanders. � Keep hands, feet and loose

Inhaltszusammenfassung zur Seite Nr. 5

ENGLISH EN Introduction and Machine Specifications MODEL 07104A 07111A 07117A Electrical 230~, 60Hz 230V~, 50Hz 230V~, 50Hz 230~, 50Hz Requirements 15.7 A, 3.7 kW 11.8 A, 3.0 kW 12.0 A, 3.0 kW 12.0 A, 3.0 kW Sound Emisson 93.0 dB(A) 96.2 dB(A) 96.2 dB(A) 96.2 dB(A) (Lpm) 2 2 2 Vibration <.15 in/s 2.88 m/s rms 2.88 m/s rms 2.88 m/s rms Motor 4 Hp Induction 2.2 kW Induction 2.2 kW Induction 2.2 kW Induction Contact Wheel Rate 2450 rpm 2042 rpm 2042 rpm 2042 rpm Abrasive Rate 4500 ft/min 3750 ft/mi

Inhaltszusammenfassung zur Seite Nr. 6

ENGLISH EN 230V Electrical Connection Instructions CAUTION: This machine will operate only on AC frequency and on electrical volt- age shown on the equipment nameplate. Make sure you have the correct frequency and voltage before connecting the power cord to an outlet. See the example in figure 1. This machine must be connected to an electrical source with an earthing conductor in order to protect the operator from electric shock. This machine has an approved power cord with three conductors a

Inhaltszusammenfassung zur Seite Nr. 7

ENGLISH EN How to Transport the Machine WARNING: The machine is heavy. Remove the motor from the machine before transporting. Get help loading the machine and motor. Use proper lifting techniques. Transporting the Machine - Using the Dolly Cart A B B A CAUTION: When deploying the dolly, the drum will contact the floor or ground over which the machine is resting. Care should be taken to avoid surfaces which might damage or contaminate Figure 2 the drum. CAUTION: While transporting using the

Inhaltszusammenfassung zur Seite Nr. 8

ENGLISH EN How to Transport the Machine 4. To store the dolly in the "UP" position, swing the dolly up against the top of the mainframe as far as it will travel and close the quick release levers to secure it in place. (See Figure 5) 5. To remove the dolly, loosen the quick release adjustment nuts until the levers and nuts clear the counter-bore on the dolly brackets, and remove the dolly. 6. Tighten the adjustment nuts until the quick release levers can be closed to secure the dolly in place.

Inhaltszusammenfassung zur Seite Nr. 9

  ENGLISH EN How to Transport the Machine CAUTION: Premature bearing failure can occur if the fan belt is set too tight. The fan belt should deflect ½" at the center of the span with 5 lbs. of pressure. NOTE: It is necessary to adjust the fan belt indepen- dently during this procedure or during replacement. The idler pulley is factory adjusted. Transporting the Machine by Carrying - Two People 1. Person #1 places his hands under the front of the machine's main casting. 2. Person #2 lifts

Inhaltszusammenfassung zur Seite Nr. 10

ENGLISH EN Machine Set-Up (Cont) 7. Install a new abrasive belt by sliding the abrasive over the tension roller and contact wheel. (See figure 12) 8. Rotate the release lever backward to tighten the abrasive belt. CAUTION: Do not force the release lever. Doing so can damage the track- ing mechanism and cause the abrasive belt to mis-track. Figure 12 9. Depending on the model, the control switch is found on either the operationg handle or on the motor. Verify that the control switch is set to "O

Inhaltszusammenfassung zur Seite Nr. 11

ENGLISH EN To operate the machine follow this procedure: How to Operate the Machine 1. Before sanding, decide on best approach for sanding desired area. If the floor is uneven, it DANGER: Sanding/finishing wood floors may be necessary to sand diagonally to the can create an environment direction that the floor is laid. This will help that can be explosive. Ciga- "pull" or stretch low and high spots in the floor over a greater area, producing a flatter surface. rette lighters, pilot lights and

Inhaltszusammenfassung zur Seite Nr. 12

ENGLISH EN How to Operate the Machine 6. When contact wheel is fully engaged with the surface, gradually adjust your pace for adequate finish removal. Keep sander in motion while the contact wheel is engaged with the surface or dwell marks will occur. 7. Move the machine in the direction of the grain in the wood whenever it is possible. Sand the surface at a constant pace. 8. Gradually feather-cut out at the termination point by easing the contact wheel up with the control lever. (See Figure 1

Inhaltszusammenfassung zur Seite Nr. 13

ENGLISH EN Sanding Cuts and Sandpaper Initial Cut Final Cuts The purpose of the initial cut is to remove old finish The purpose of a finishing cut is to remove the and gross imperfections on the floor surface. The scratches produced during the initial cut. Use a sanding equipment should be adjusted to heavy fine (60 - 80 grit) grain abrasive and a reduced sanding pressure setting and a coarse abrasive sanding pressure setting. belt should be used. If the surface is severely damaged by deep sc

Inhaltszusammenfassung zur Seite Nr. 14

ENGLISH EN Chatter Wave Prevention Clarke Sanders are designed and manufactured to the most rigid tolerances. However, after a finishing cut it is possible to see “chatter” or “waves”. The best guarantee to remove the chatter is to finish the floor with a rotating horizontal sander, such as Clarke’s Sander 16. To minimize chatter when using a belt or drum sander the following steps should be taken: 1. DRUM MARKS...are caused by the operator lowering the drum to the floor without forward traver

Inhaltszusammenfassung zur Seite Nr. 15

ENGLISH EN Sander Adjustment Procedures DANGER: Electrocution could occur if main- tenance and repairs are performed on a unit that is not properly dis- connected from the power source. Disconnect the power supply be- fore attempting any maintenance or service. DANGER: Moving parts of this machine can cause serious injury and/or dam- age. Keep hands, feet and loose clothing away from all moving parts of the sander. The following information provides details on how to Figure 15 adjust differe

Inhaltszusammenfassung zur Seite Nr. 16

ENGLISH EN Sander Adjustment Procedures 2. Drive the adjusting screw in, to sand heavier on the left (the drive belt side). Back the adjusting screw out, to sand heavier on the right (the side opposite the drive belts). Test the setting on an even surface. Make further adjustments if necessary. 3. Mark new pointer location on main frame Belt Tracking AA NOTE: The sanding belt should run evenly on the face of the contact wheel. For this, the outer edge of the sanding belt must be .09 inche

Inhaltszusammenfassung zur Seite Nr. 17

ENGLISH EN Sanding Adjustment Procedures To decrease the travel or reduce the reach on the grip control follow this procedure: 1. Loosen the locknut on the control rod. (See figure 20A) 2. Screw the control rod adjuster"out" until desired reach is found. 3. Tighten the locknut. Routine Maintenance A The following items need to be periodically inspected and maintained to keep your sander in good working condition. Sanding Chamber Periodically blow out the sanding chamber to prevent Figure 20 l

Inhaltszusammenfassung zur Seite Nr. 18

ENGLISH EN Routine Maintenance Bearings Periodically check the bearings for wear or damage according to the following schedule: st Guide rollers after 1 650 hrs. st Idler pulley after 1 1500 hrs. st Fan shaft after 1 2500 hrs. st Tension roller after 1 2500 hrs. st Arbor shaft after 1 5000 hrs. st Motor shaft after 1 5000 hrs. Rollers Periodically check the guide rollers and the tension roller for wear. ® -18- Clarke American Sanders Operator's

Inhaltszusammenfassung zur Seite Nr. 19

ENGLISH EN Troubleshooting Problem Cause Action Drive belts slip. Insufficient tension. Tension drive belt as described in (Squeaking or squealing sound) adjustment procedures. Worn belts. Replace belts. Squealing, growling or grinding Damaged and/or worn bearing. Remove drive belts, rotate arbor noise coming from machine. motor, fan, shafts and idler pulley to locate dragging or rough bearing. Contact an authorized dealer. Dust pickup is poor. Dust bag is full. Empty contents of bag. Dust bag i

Inhaltszusammenfassung zur Seite Nr. 20

ENGLISH EN Troubleshooting Problem Cause Action Burning or glazing. Dull abrasive. Replace abrasive. Excessive sanding pressure. Decrease sanding pressure setting. (Fig. #16, page 15). Too fine of an abrasive belt. Use coarser abrasive. Slow cutting. Dull abrasive. Replace abrasive. Too fine of an abrasive belt. Use a coarser abrasive belt. Insufficient sanding pressure. Increase sanding pressure setting. (Fig. #16, page 15). Waves on sanded surface. Debris on wheels. Remove and clean wheels. Fl


Ähnliche Anleitungen
# Bedienungsanleitung Kategorie Herunterladen
1 Clarke ALTO 2300 Handbuch Schleifmaschine 0
2 Clarke 1600 Handbuch Schleifmaschine 1
3 Clarke ALTO 2000 Handbuch Schleifmaschine 2
4 Clarke ALTO FM-1500HD Handbuch Schleifmaschine 3
5 Clarke 07117A Handbuch Schleifmaschine 0
6 Clarke ALTO 1700HD Handbuch Schleifmaschine 0
7 Clarke CFP-200 Handbuch Schleifmaschine 2
8 Clarke CFP-1700 Handbuch Schleifmaschine 2
9 Clarke ALTO C2K Series Handbuch Schleifmaschine 1
10 Clarke Alto MP-1800 Handbuch Schleifmaschine 3
11 Clarke CFP-130 Handbuch Schleifmaschine 0
12 Clarke CFP-170 Handbuch Schleifmaschine 10
13 Clarke CFP-2000 Handbuch Schleifmaschine 0
14 Clarke CFP-2000DS Handbuch Schleifmaschine 0
15 Clarke Propane Floor Burnisher Handbuch Schleifmaschine 0
16 3Com Tech Note Wireless Remote Control TT24 Handbuch Schleifmaschine 2
17 Agilent Technologies 16440A SMU Handbuch Schleifmaschine 0
18 Alpha Industries AEP-458 Handbuch Schleifmaschine 0
19 Bausch & Lomb DISCOVERER 78-1600 Handbuch Schleifmaschine 12
20 Agilent Technologies 83485A Handbuch Schleifmaschine 1