Inhaltszusammenfassung zur Seite Nr. 1
Z100 / Z300 Z500
Z700
XE 100 XE 200 XE 300
Elliptical Elliptical Elliptical
OWNER’S MANUAL
PLEASE CAREFULLY READ THIS ENTIRE MANUAL BEFORE
OPERATING YOUR NEW ELLIPTICAL!
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Product Registration . .2 Important Safety Instructions 3 Important Electrical Information 4 Important Operation Instructions ..4 Assembly Instructions .5 Features .. 21 Operation of Your New Elliptical ..22 Maintenance 43 Manufacturer s Limited Warranty .44 ATTENTION-THIS ELLIPTICAL IS INTENDED FOR RESIDENTIAL USE ONLY AND IS WARRANTED FOR THAT APPLICATION. ANY OTHER APPLICATION VOIDS THIS WARRANTY IN ITS ENTIRETY. 1
Inhaltszusammenfassung zur Seite Nr. 3
CONGRATULATIONS ON YOUR NEW ELLIPTICAL AND WELCOME TO THE SPIRIT FAMILY! Thank you for your purchase of this quality elliptical trainer from Spirit Manufacturing, Inc. Your new elliptical was manufactured by one of the leading fitness manufacturers in the world and is backed by one of the most comprehensive warranties available. Through your dealer, Spirit will do all we can to make your ownership experience as pleasant as possible for many years to come. The local dealership where you purchased
Inhaltszusammenfassung zur Seite Nr. 4
Important Safety Instructions WARNING - Read all instructions before using this appliance. Do not operate elliptical on deeply padded, plush or shag carpet. Damage to both carpet andelliptical may result. Keep children away from the elliptical. There are obvious pinch points and other caution areas that can cause harm. Keep hands away from all moving parts. Never operate the elliptical if it has a damaged cord or plug. If the elliptical is not working properly, call your dealer. Keep the c
Inhaltszusammenfassung zur Seite Nr. 5
Important Electrical Information WARNING! NEVER remove any cover without first disconnecting AC power supply. If A.C. voltage varies by ten percent (10%) or more, the performance of your elliptical may be affected. Such conditions are not covered under your warranty. If you suspect the voltage is low, contact your local power company or a licensed electrician for proper testing. NEVER expose this to rain or moisture. This product is NOT designed for elliptical Use outdoors, near a pool or spa
Inhaltszusammenfassung zur Seite Nr. 6
Assembly Pack Check List (XE100) Step 1 #96. 3/8" x 2T #84. 3/8" x 23 x 1.5T #66. M5 x 10m/m Split Washer (1pc) Curved Washer (2pcs) Phillips Head Screw (4pcs) #103. 3/8" x 3/4" #60. 3/8" x 2-1/4" Hex Head Bolt (2pcs) Hex Head Bolt (1pc) Step 2 #59. 5/16"x15m/m #83. 17 #79.5/16"x23x1.5T Hex Head Bolt (2 pcs) Flat Washer (2pcs) Wave Washer (2 pcs) Step 3 #71. 5/16" x 7T #80. 5/16" x 20x 1.5T #104. 5/16 x 1-1/4 Nylon Nut (2 pcs) Flat Washer (2 pcs) Hex Head Bolt (2 pcs) 5
Inhaltszusammenfassung zur Seite Nr. 7
Step 4 #87. 3.5x12m/m #105.M5 x 15m/m Phillips Head Screw (17pcs) Self Tapping Screw (10pcs) Tools #108. Phillips Head Screw Driver (1 pc) #107. Short Phillips Head Screw Driver (1 pc) #109. 12m/m Wrench (1pc) #106. 13/14m/m Wrench (1pc) 6 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 8
Assembly Pack Check List (XE200) Step 1 #96. 3/8" x 2T #84. 3/8" x 23 x 1.5T #66. M5 x 10m/m Split Washer (1pc) Phillips Head Screw (4pcs) Curved Washer (2pcs) #103. 3/8" x 3/4" #60. 3/8" x 2-1/4" Hex Head Bolt (2pcs) Hex Head Bolt (1pc) Step 2 #97.3/8"x30x2T #81. 25 #103. 3/8"x3/4" Flat Washer (2pcs) Hex Head Bolt (2 pcs) Wave Washer (2 pcs) Step 3 #71. 5/16" x 7T #80. 5/16" x 20 x 1.5T #104. 5/16 x 1-1/4 Nylon Nut (2 pcs) Flat Washer (2 pcs) Hex Head Bolt (2 pcs) 7
Inhaltszusammenfassung zur Seite Nr. 9
Step 4 #87. 3.5x12m/m #105.M5 x 15m/m Phillips Head Screw (21pcs) Self Tapping Screw (18pcs) Tools #108. Phillips Head Screw Driver (1 pc) #107. Short Phillips Head Screw Driver (1 pc) #109. 12m/m Wrench (1pc) #106. 13/14m/m Wrench (1pc) 8 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 10
Assembly Instructions( XE100 / XE200) UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to
Inhaltszusammenfassung zur Seite Nr. 11
*STEP 2: XE100 ONLY: HANDLE BAR ASSEMBLY 1. Install the two 17m/m Wave Washers (83) onto the Left and Right side of the Handle Bar axle. 2. Slide the Left (10) and Right (11) Handle Bars onto the appropriate side of the axle. The handlebars have a small sticker on them indicating L (left) and R (right). 3. Put the two 5/16" x 23mm Flat Washers onto the two 5/16" x 15m/m Hex Head Bolts and install, and tighten, in the threaded holes in the ends of the axle. *STEP 2: XE200 ONLY: HANDLE BAR ASSEMBL
Inhaltszusammenfassung zur Seite Nr. 12
2. Install the connecting arm covers (57,57-1 & 58,58-1) over the connection of the rod end and handle bars (10 & 11) with eight M5 x 15m/m Phillips Head Screws (105) and eight 3.5x12m/m self tapping screws (87) by using the Phillips head screw driver. 3. Install the two Wheel Covers (52) using the four M5x15m/m Phillips Head Screws (105). 4. Locate the two Rear Stabilizer Covers (19,20) and two Middle Stabilizer Covers (19,20) for the Rear Rail Assembly and install with four M5 x 15m/m Screws (
Inhaltszusammenfassung zur Seite Nr. 13
Assembly Drawing (XE100) 12 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 14
Assembly Drawing (XE200) 13 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 15
Assembly Pack Check List (XE300) Step 1 #96. 3/8" x 2T #84. 3/8" x 23 x 1.5T #66. M5 x 10m/m Split Washer (1pc) Curved Washer (2pcs) Phillips Head Screw (4pcs) #103. 3/8" x 3/4" #60. 3/8" x 2-1/4" Hex Head Bolt (2pcs) Hex Head Bolt (1pc) Step 2 #97.3/8"x30x2T #81. 25 Wave Flat Washer (2pcs) Washer (2 pcs) #87. 3.5x12m/m #103. 3/8"x3/4"mm Self Tapping Screw (8pcs) Hex Head Bolt (2 pcs) 14 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 16
Step3 #71. 5/16" x 7T #80. 5/16" x 20x 1.5T #104. 5/16 x 1-1/4 Nylon Nut (2 pcs) Flat Washer (2 pcs) Hex Head Bolt (2 pcs) #87. 3.5x12m/m #105.M5 x 15m/m Phillips Head Screw (11pcs) Self Tapping Screw (10pcs) Step 4 #91. 5/16"x 3/4 #105.M5 x 15m/m Hex Head Bolt (4 pcs) Phillips Head Screw (26pcs) 15 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 17
Tools #108. Phillips Head Screw Driver (1 pc) #107. Short Phillips Head Screw Driver (1 pc) #109. 12m/m Wrench (1pc) #106. 13/14m/m Wrench (1pc) 16 XE100 / XE200 / XE300 Elliptical
Inhaltszusammenfassung zur Seite Nr. 18
Assembly Instructions (XE300) UNPACKING THE UNIT 1. Using a razor knife (Box Cutter) cut the outside, bottom, edge of box along the dotted Line. Lift Box over the unit and unpack. 2. Carefully remove all parts from carton and inspect for any damage or missing parts. If damaged parts are found, or parts are missing, contact your dealer immediately. 3. Locate the hardware package. The hardware is separated into steps. Remove the tools first. Remove the hardware for each step as needed to avoid co
Inhaltszusammenfassung zur Seite Nr. 19
STEP 2: HANDLE BAR ASSEMBLY 1. Install the two 28m/m Wave Washers (81) onto the Left and Right side of the Handle Bar axle. 2. Slide the Left (10) and Right (11) Handle Bars onto the appropriate side of the axle. The handlebars have a small sticker on them indicating L (left) and R (right). 3. Put the two 3/8 X 30mm Flat Washers (97) onto the two 3/8 X 3/4 Hex Head Bolts (103) and install, and tighten, in the threaded holes in the ends of the axle. 4. Connect the two wires together (124, 125)
Inhaltszusammenfassung zur Seite Nr. 20
7. Install the center support brace by sliding the front tab between the plastic side case and stabilizer tube. Secure in the rear with two 5/16 x3/4 Hex Head Bolt (91). PLEASE ENSURE ALL FASTENERS ARE TIGHT AFTER THE COMPONENTS HAVE BEEN ASSEMBLED. POWER CONNECTOR LOCATED ON FRONT, LEFT HAND SIDE OF UNIT. 19 XE100 / XE200 / XE300 Elliptical
