Inhaltszusammenfassung zur Seite Nr. 1
Installation Guide
2175BEVS Beverage Center
and 2175BEVOL2 Beverage
Center with Overlay
www.U-LineService.com
Phone (414) 354-0300 • FAX (414) 354-7905
Service & Parts Tech Lines Phone (800) 779-2547 FAX (414) 354-5696
OnlineService@U-Line.com
©2008 U-Line Corporation
03/2008
Inhaltszusammenfassung zur Seite Nr. 2
2175BEVS/2175BEVOL2 Beverage Center Contents 1 Follow Safety Precautions 1-Follow Safety Precautions . . . . . . . . . . . . . . . . . . . . . 2 2-Inspect and Plan . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 IMPORTANT Exterior Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . 4 PLEASE READ all instructions completely before 3-Prepare Site . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 attempting to install or operate the unit. Cut-Out Dimensions
Inhaltszusammenfassung zur Seite Nr. 3
2175BEV/2175BEVOL2 Beverage Center General Precautions 2 Inspect and Plan Use this appliance for its intended purpose only and follow these general precautions along with those listed You have received a carton containing your 2175BEVS or throughout this guide: 2175BEVOL2 Beverage Center with a package inside containing a Use and Care Guide, a Product Registration WARNING Card and an Anti-Tip Bracket Installation Kit. 2175BEVOL2 units are shipped with an additional package of SHOCK HAZARD
Inhaltszusammenfassung zur Seite Nr. 4
2175BEVS/2175BEVOL2 Beverage Center After all the protective coating has been removed from 3 Prepare Site the unit/door, clean all Stainless Steel surfaces with Claire Stainless Steel Polish and Cleaner or comparable product or a mild detergent and warm water solution and soft Your U-Line product has been designed for either free- cloth. Do NOT use abrasive cleaning agents. standing or built-in installation. When built-in, your unit does not require additional air space for top, sides or rea
Inhaltszusammenfassung zur Seite Nr. 5
2175BEV/2175BEVOL2 Beverage Center Product Dimensions Door Swing/Clearances Information Wood Overlay units have a zero clearance for the door to 25 - 3/8" open 90° (see Figure 3). Stainless Steel models require a Including minimum of 2-1/8" door clearance to accommodate the Handle handle if the unit is installed next to a wall or similar type of structure. Wall Wall 1/4" Min. 2-1/8" Min. 21" 21" 34 - 1/8" 25-1/2" 25-1/2" 90 90 Door Swing Door Swing Wood Overlay Stainless Steel 23 - 15/16" Fi
Inhaltszusammenfassung zur Seite Nr. 6
2175BEVS/2175BEVOL2 Beverage Center Side-By-Side Installation 4 Prepare Racks and Door Frame Instructions The U-Line Beverage Center is equipped with wood- For a complete refreshment center, install your 2175BEVS trimmed wine racks that are coated at the factory with a or 2175BEVOL2 unit beside a U-Line Refrigerator, Ice clear vinyl sealer, which will adequately protect the wood Maker or Combo Model (see Figure 4 for typical cut-out). in normal usage. A final finish coat was not applied so
Inhaltszusammenfassung zur Seite Nr. 7
2175BEV/2175BEVOL2 Beverage Center To insert a rack in the cabinet: WARNING 1. Align the left and right rack channels with the tracks To prevent permanent damage to the inner liner in the cabinet, and ensuring an even track of your unit, the wood trim MUST be removed engagement on both sides, gently push the rack into from the unit for staining and/or finishing. Allow the cabinet until it stops. stain/finish to dry thoroughly (at least 24 hours 2. Before reloading the rack, ensure proper
Inhaltszusammenfassung zur Seite Nr. 8
2175BEVS/2175BEVOL2 Beverage Center Final finish-only application: 1. Remove all screws securing wood trim to interior components, and remove the trim. 2. Lightly scruff sand the wood trim with 280 or finer grit sandpaper. Hinge plugs 3. Remove sanding dust with a clean, dry cloth. 4. The factory-applied seal is compatible with virtually all finishes. A low odor, water clean up, quick-drying finish ® ® such as Minwax Polycrylic Protective Finish is ® ® recommended (Minwax Polycrylic is an
Inhaltszusammenfassung zur Seite Nr. 9
2175BEV/2175BEVOL2 Beverage Center 7. With bottom of door facing up, remove pivot plate (2 10. Install metal hinge plugs removed in step 2 in old hinge screws), flip over, and remount on opposite side of door holes (3 each, top and bottom). (Figure 11). Be sure angled side of plate faces center. door pivot plate bottom hinge screw pin ULIN_0274_A Figure 12 Figure 11 8. Holding door upright with top of door tilted forward, place hole of door pivot plate on bottom hinge screw pin (Figure 12).
Inhaltszusammenfassung zur Seite Nr. 10
2175BEVS/2175BEVOL2 Beverage Center 1. Use the following instructions to create or have a Overlay Frame wood overlay panel created for your Échelon Wine (2175BEVOL2 Units Only) Captain or Beverage Center model as shown in Figure 13. FRAME PREPARATION 2. Drill holes for pivot pins, upper door hinge and lower IMPORTANT door hinge as shown. The thickness of the wood overlay panel must be 3. The overlay door panel must be installed in accordance 3/4". with the Installation Instructions startin
Inhaltszusammenfassung zur Seite Nr. 11
2175BEV/2175BEVOL2 Beverage Center PREPARE THE NEW OVERLAY PANEL IMPORTANT The overlay door panel must not weigh more than 20 lbs. The thickness of the door panel must be 3/4". 1. Place a towel, or other similar, soft, non-marking material out on a flat clean surface. Be sure the material is large enough to have the wood panel not touch the hard, marking surface. 2. Lay the wood panel out with the front side of the wood facing down. 3. Cut the foam tape into four pieces, two pieces the wid
Inhaltszusammenfassung zur Seite Nr. 12
2175BEVS/2175BEVOL2 Beverage Center Note: After attaching the wood to the door, double check the bottom pivot hole location. If the hole in the pivot DOOR FRAME bracket is covered by any wood, chase thru the hole with a 11/32” drill to open hole in door panel. DO NOT drill TAPE deeper than 1/4” deep. ASSEMBLING DOOR TO CABINET 14. Starting at the corners and working toward the center, push the door gasket back into place. Make sure gasket is fully seated on all four sides and corners. 15.
Inhaltszusammenfassung zur Seite Nr. 13
2175BEV/2175BEVOL2 Beverage Center 5 Adjust Door Checking Door Alignment Slotted Mounting The unit’s door is aligned at the factory before shipment. Holes However, its alignment could have been disturbed during Angled Edge Towards Center shipment or during overlay frame installation. of Door IMPORTANT Properly aligned, the door should be 1/8" below the top of the unit’s cabinet, NOT flush with the top (see Figure 20). Raise Lower Outside Outside Door Edge Door Edge Figure 22 1/8" 3. See Figur
Inhaltszusammenfassung zur Seite Nr. 14
2175BEVS/2175BEVOL2 Beverage Center should be placed along top edge and side edge as 6 Prepare Power Supply shown (see Figure 25). Electrical Specifications CAUTION Electrical installation must observe all state and local codes. This unit requires connection to a grounded (three- prong), polarized receptacle that has been placed by a qualified electrician. 1 The unit requires a grounded and polarized 115 VAC, 60 Hz, 15A power supply (normal household current). An individual, properly ground
Inhaltszusammenfassung zur Seite Nr. 15
2175BEV/2175BEVOL2 Beverage Center 2. Place the unit into the area where it will be installed. Check the door, sides and top for a proper fit. Also test the make sure the door opens and closes freely. 3. Remove grille and place mark on the floor at the front of the unit. Also place a mark on the floor in the center of the unit (Figure 27). Drill Holes and Mount Anti-Tip Brackets to Floor Back Wall Back of Unit Front of Unit Figure 29 CAUTION Other hardware is required for floors made of mat
Inhaltszusammenfassung zur Seite Nr. 16
2175BEV/2175BEVOL2 Beverage Center SIDE-BY-SIDE INSTALLATION 9 Start-Up for the First Time 1. Remove screws shown (Figure 31). Initial Start-Up CAUTION The unit is shipped with the control preset. No adjustments Be sure to remove and discard screw shown. Failure should be necessary at this time. For information about to do so may cause damage to the bracket and/or Adjusting the Temperature Control, see the Use and Care unit. Guide. 1/4” Start-Up Troubleshooting Problem Q: Remove and Unit d
Inhaltszusammenfassung zur Seite Nr. 17
For more than four decades, U-Line has distinguished itself as the leader in built-in undercounter ice making, refrigeration and wine storage appliances. U-Line Corporation, located in Milwaukee, WI, is a family operated manufacturer of built-in ® ® undercounter icemakers, Combo icemaker/refrigerators, Wine Captain wine storage units, refrigerators, refrigerated drawers and refrigerator/freezers. ©2008 U-Line Corporation Publication No. 30225E 03/2008 Rev. A
