Inhaltszusammenfassung zur Seite Nr. 1
II
_,!STALLATION
STRUCTIONS
IIIII III II III I I I I I IiI' '111
SUB-ZERO
Inhaltszusammenfassung zur Seite Nr. 2
I I I IIIII IIIIIII I I I IIIII IIIIII I I HIII PRI -INSTALLATION INSTRUCTIONS PRE-INSTALLATION SPECIFICATIONS PREPARATION FOR INSTALLATION Step 1 Prepare the finished rough opening to accept the installation of the Sub-Zero. NOTE: Carefully read the "Pre-lnstallation Specifications" chart below. LOCATE ELECTRICAL OUTLET WITHIN TOP St-_DED _ NE,, WITHIN BOTIOM _DAREA =W" LOCATE_ SUPPLY SHUT OFF V4LV£ A '_ /" A ._ Figure I MODELS 501F AND 501R MODELS 511, 532, 542, 550, 561 AND 590 FINISHED MINIM
Inhaltszusammenfassung zur Seite Nr. 3
I i ii ! I I I -INSTALLATION TRUCTIONS | ! ,REA [_,WARNING l REPARATION Do not use an extension cord, or two prong adapter. ;tep 2 Electrical ground is A/hen units are installed side required on this appliance. 3y side, a separating filler strip s recommended. The filler Do not under any _trip width should be added to circumstances remove he finished rough opening the power supply cord dimension. A filler strip must ground prong. _lso be used when units are This appliance is factory nstalled
Inhaltszusammenfassung zur Seite Nr. 4
INSTALLATION INSTRUCTIONS MODELS 501F AND 501R To block the unit, using the IAwARNING I wood block and hardware To remove the 501 grille, Toreduce the possibility of remove two (black) screws provided, follow these steps. the unit tipping forward, located in the lowest louver in 1) Locate and mark two wall you must reposition the the grille. Tilt the bottom of the studs against the wall where front levelers to make grille out and away, it will the refrigerator is to be contact with the floor. Yo
Inhaltszusammenfassung zur Seite Nr. 5
t '° TALLATION ,.. TRUCTIONS MODEL 590 Step 12 iSTALLATION NOTE: ROUTING, Install grille, step 7. RECESSING OR OP- IMPORTANT'. For Models _WARNING ] TIONAL EXTENDED 511, 532, 542, 550, 561 HANDLES MAY BE ;hut-off power to the wall and 590, reverse step 7 REQUIRED ON RAISED )utlet. procedure. NOTE: If using PANELS FOR FINGER panelized grille refer to CLEARANCE UNDER ;tep 9 "Grille Panel Installation." HANDLE. Refer to Figures Jnit is equipped with rollers. 28 and 29 -- "Handle )lug into 15 amp g
Inhaltszusammenfassung zur Seite Nr. 6
II llllllllll I III IIIIII INSTALLATION INSTRUCTIONS MODEL 590 B) With standard Phillips D) Next, remove the water and GRILLE PANEL screwdriver, remove door A) To install panels on the ice glasswell by removing the INSTALLATION handle on freezer and Model 590, the door handle mounting screw. Then slide and door handle trim must first refrigerator door (the door the glasswell up and pull out If optional EA panel grille is handles also act as a door be removed. The screws are as in Figure 18. purc
Inhaltszusammenfassung zur Seite Nr. 7
I II II I IIIIII I I iF'NSTALLATION .,qSTRUCTIONS 11" GRILLE ONLY 532 & SN 11" THRU T$" GRILLE ALL OTHER MODELS P_ ,l-:z-o.-0 SCREW GROMMET pin .1_,o.o, 3-o UPPER G_LLE SCREW t i Figure 21 LOWER GRILLE SCREW C) Slide panel into position in grille frame as shown in Figure 22. NOTE: When using _/4" or less, a filler is necessary. Figure 20 -,-]_ MODEL 590 D) Install screw grommets in ,4) Remove Iouvered grille. properly labeled holes in Refer to step 7. (STANDARD FEATURE) Figure 20 in the shroud B
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION INSTRUCTIONS r/d" Anchor the side panel with SIDE PANEL NOTE: Product(s) must be decorative headed screws leveled and squared before INSTALLATION (as shown) or finishing nails attempting this procedure. can be used. The screws/ If side panels are being nails must be obtained from Instructions for product utilized, please check with being tied together your local hardware supply your installer for installation store. (see Figure 24): methods or you may use one NOTE: We do not of the
Inhaltszusammenfassung zur Seite Nr. 9
i'"'ISTALLATION" ' ,,4STRUCTIONS 2) Using the Loctite on the HINGE IAWARNING l screws, install all 3 Chicago ADJUSTMENT Screw Posts. Disconnect power to unit before checking wiring Step 16 3) Inspect the units for level connections. Ifthe doors are out of again. adjustment, the top or bottom 4) Drill three (3) 3t16" holes hinge may be adjusted by [] Is blocking completed? (per specs in Figure 24) removing and discarding the (Step 8) through both outer trims. two small shipping screws. [] Is unit
Inhaltszusammenfassung zur Seite Nr. 10
IIIIIIIIIII I lU INSTALLATION INSTRUCTIONS STANDARD HANDLE RECESS SPECIFICATIONS PRODUCT SERVICE I" A _ I------- ,! T 14" ± T c 14" =: ± !i:_i MODELS 501F ,4ND 501R _]_ MODELS 532, 542 AND 561 MODELS 511 AND 550 ff you need service. Take Figure 28 necessary steps to preserve food inunit. Door(s) should be left closed as much as MODEL A (WIDTH) B (WIDTH) C (HEIGHT) D E F possible until unit is back in 532 1715115" 2711116" 6711/16" 385/32 . service. Please have model 542 155/8" 24" 6711/16" 385/3
Inhaltszusammenfassung zur Seite Nr. 11
LISTAL_LATION ,.4STRUCTIONS ,I _ECOMMENDATIONS :OR RAISED 2 H 3" 11 =ANELS Optional F" _ecause of different door panel Extended Handle Jesigns, routing, recessing, or Jseof optional extended handles nay be necessary for finger "learance when using raised 1_" Panel Optional/_ / )anels greater than 114"total Standard I 1" Panel hickness. (50# per door panel D-Style" I Full-Length naximum weight limit.) Han_lle I ¾" Panel Handle _ee Figure 28 for location of I _ffset when using specific V2" Panel "
Inhaltszusammenfassung zur Seite Nr. 12
THINK SAFETYt If you are storing or disposing of your old refrigerator, please do it safely. Read the enclosed safety booklet from the Association of Home Appliance Manufacturers. CHILD ENTRAPMENT ACCIDENTS CAN BE TRAGIC! SUB-Z SUB SUB-ZERO FREEZER CO., INC. P.O. BOX 44130, MADISON, Wl 53744-4130 (608) 271-2233 FORM NO. 3-75-216-16 PRINTED IN U.S.A. g/96