Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION GUIDE
Wine Storage
Inhaltszusammenfassung zur Seite Nr. 2
Contents Important Note Wine Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 To ensure the safe and efficient installation of Sub-Zero equipment, please take note of the following types of Models 424G and 424FSG Installation . . . . . . . . . . . . . . . 4 highlighted information throughout this guide: Models 427G and 427RG Installation . . . . . . . . . . . . . . . 16 IMPORTANT NOTE highlights information that is especially Model WS-30 Installation . . . . . . .
Inhaltszusammenfassung zur Seite Nr. 3
Wine Storage 3 subzero.com Sub-Zero Wine Storage The importance of the installation of the Sub-Zero wine RATING PLATE storage unit cannot be overemphasized. Installation should be done by a qualified installer. Before you begin the installation process, it is recom- mended that you read this entire installation guide. There are key details that you should take special care to observe during the installation. By reading these instruc- tions carefully, you will make the installation process easier
Inhaltszusammenfassung zur Seite Nr. 4
Models 424G and 424FSG Installation 4 Models 424G and 424FS OVERALL DIMENSIONS 7 1 5 23 /8" (606) 24" (610) 24 /4" (616) 24 /8" (625) 3 34" 34 /16" (864) (868) 4" (102) 4" (102) 3 3 25 /8" 25 /8" (645) (645) 3 3 2 /8" (60) 2 /8" (60) MODEL 424G MODEL 424FSG Door swing clearances are based on stainless steel door and handle dimensions.
Inhaltszusammenfassung zur Seite Nr. 5
Models 424G and 424FSG Installation 5 subzero.com Models 424G and 424FSG Installation The model 424FSG wine storage unit is designed to be OPENING DIMENSIONS attractive in a stand alone setting. Model 424G must be built in. Refer to the previous page for overall dimensions TOP VIEW and door swing clearances for models 424G and 424FS. 24" (610) OPENING Make sure that the finished rough opening where the DEPTH model 424G wine storage unit is to be installed is properly prepared. Refer to the illus
Inhaltszusammenfassung zur Seite Nr. 6
Models 424G and 424FSG Installation 6 Electrical Requirements For models 424G and 424FSG, the electrical supply Electrical Requirements should be located within the shaded area shown in the Power Supply 115 V AC, 60 Hz illustration. Follow the National Electrical Code and local Circuit Breaker 15 amp codes and ordinances when installing the receptacle. A Receptacle 3-prong grounding-type separate circuit, servicing only this appliance is required. A ground fault circuit interrupter (GFCI) is not
Inhaltszusammenfassung zur Seite Nr. 7
Models 424G and 424FSG Installation 7 subzero.com Electrical Requirements Moving the Unit HOME ALARM SYSTEM Before moving the wine storage unit into position, make sure all opening dimensions and electrical requirements If a home alarm system is to be used, refer to home alarm are complete and accurate. connections on page 11. In addition to operating power, the installer may also be required to supply a home IMPORTANT NOTE: The floor under the undercounter unit automation system lead to the uni
Inhaltszusammenfassung zur Seite Nr. 8
Models 424G and 424FSG Installation 8 Anti-Tip Bracket Installation MODEL 424FSG If you are installing the model 424FSG in a space deeper To prevent the unit from tipping forward and provide a 5 stable installation, the unit must be secured in place than 24 /8" (625), the anti-tip bracket must be installed no 5 with the anti-tip bracket. more than 24 /8" (625) deep, so it engages the unit properly. It is important that this measurement be made from the front surface of the door, to the back of t
Inhaltszusammenfassung zur Seite Nr. 9
Models 424G and 424FSG Installation 9 subzero.com Anti-Tip Bracket Installation MODEL 424FSG—WOOD FLOORS INSTALL CONCRETE WEDGE ANCHORS: 1 1 3 Use the four #12 x 2 /2" wood screws and the four /4" 1) Drill a /8" (10) diameter hole any depth exceeding the 3 flat washers provided. Drill pilot holes /16" (5) diameter minimum embedment. Clean the hole or continue maximum, and be sure that the screws penetrate through drilling additional depth to accommodate drill fines. the flooring material and int
Inhaltszusammenfassung zur Seite Nr. 10
Models 424G and 424FSG Installation 10 Position the Unit If you are adding an accessory lock kit to your wine For model 424FSG, adust the leveling legs so the top of 5 storage unit, it should be installed before you position the the unit is no more than 34 /8" (879) above the floor. This is unit. The accessory lock kit and additional instructions are to allow the unit to engage the anti-tip bracket properly. available through your authorized Sub-Zero dealer, or call Center the model 424FSG in fr
Inhaltszusammenfassung zur Seite Nr. 11
Models 424G and 424FSG Installation 11 subzero.com Level the Unit Home Alarm Connections Using an adjustable wrench or pliers, turn each of the four Before the kickplate is installed, all necessary wiring leveling legs clockwise to raise the unit and counterclock- connections in the compressor compartment should be wise to lower the unit. Refer to the illustration below for completed. location of the leveling legs. If a home alarm system is to be installed on the wine For model 424G, the counter
Inhaltszusammenfassung zur Seite Nr. 12
Models 424G and 424FSG Installation 12 Kickplate Installation Door Panel Once the unit is leveled and wiring connections made, MODEL 424G 1 the kickplate can be installed. Use the two #10 x /2" Model 424G is offered in two design applications; stain- stainless steel screws that are provided with the kickplate. less steel (/S) and overlay (/O). Each of these designs have Refer to the illustration below. a full-view glass door. IMPORTANT NOTE: The kickplate must be removed for The stainless steel
Inhaltszusammenfassung zur Seite Nr. 13
Models 424G and 424FSG Installation 13 subzero.com Overlay Door Panel MODEL 424G The door panel is then lowered from the door frame, tenon centers removed, the door opened and the screws driven 5 Inspect the door panel for the minimum /8" (16) thickness, into the panel through the black tape on the door frame, the finished inside edge. The glass door has a 10 lbs (5 kg) using the center marks to locate the screws. weight limit. Refer to the wine storage section of the The screw holes inside the
Inhaltszusammenfassung zur Seite Nr. 14
Models 424G and 424FSG Installation 14 Overlay Door Panel IMPORTANT NOTE: Install screws in all the mounting holes in the door frame. The nature of the door panel with The wine storage unit door is made with a sealed a narrow outer rim and no connecting center member double wall tempered glass core. The drill must not requires the support provided by the glass door. contact this core when drilling. Be sure the hole is centered on the small groove in the front of the door After the door panel ins
Inhaltszusammenfassung zur Seite Nr. 15
Models 424G and 424FSG Installation 15 subzero.com Hinge Adjustment Complete the Installation IMPORTANT NOTE: The wine storage unit must be When you have completed installation of the model 424G installed and leveled before door hinge adjustments can or 424FSG wine storage unit, refer to page 54 for an be made. installation checklist and page 55 for service information. The top and bottom cabinet hinges on models 424G and 424FSG are held in place with three permanent adjust- ment screws and two
Inhaltszusammenfassung zur Seite Nr. 16
Models 427G and 427RG Installation 16 Models 427G and 427R OVERALL DIMENSIONS 27" (686) 24" (610) 27" (686) 24" (610) 14"(356) 14"(356) 13 13 /16" /16" (21) (21) 9 9 78 /16" 78 /16" (1995) (1995) 80" 80" (2032) (2032) OPENING OPENING 3 HEIGHT HEIGHT /8" (10) 1 13 /4" 1 /2" (337) (13) 1 34 /2" 1 10 /4" (876) (260) 3 20 /8" (518) 15 3 8 /16" 9 /4" (227) (248) 4" 4" 1 1 HEIGHT DIMENSIONS ± /2" (13) (102) HEIGHT DIMENSIONS ± /2" (13) (102) 24" 24" (610) (610) 5 5 4 /8" 4 /8" (117) (117) 1 1 1 25 /2"
Inhaltszusammenfassung zur Seite Nr. 17
Models 427G and 427RG Installation 17 subzero.com Models 427G and 427RG Installation Make sure that the finished rough opening where the wine OPENING DIMENSIONS storage unit is to be installed is properly prepared. Refer to the opening dimensions illustrations for models 427G TOP VIEW and 427R on the previous page. 25" (635) OPENING IMPORTANT NOTE: The floor under the wine storage unit DEPTH must be at the same level as the surrounding finished floor to allow for removal of the unit for servicin
Inhaltszusammenfassung zur Seite Nr. 18
Models 427G and 427RG Installation 18 Electrical Requirements For models 427G and 427RG, the electrical supply should be located within the shaded area shown in the illustration The outlet must be checked by a qualified electrician below. Follow the National Electrical Code and local codes to be sure that it is wired with the correct polarity. Verify and ordinances when installing the receptacle. A separate that the outlet is properly grounded. circuit, servicing only this appliance is required.
Inhaltszusammenfassung zur Seite Nr. 19
Models 427G and 427RG Installation 19 subzero.com Electrical Requirements Anti-Tip Bracket Installation HOME ALARM SYSTEM If a home alarm system is to be used, refer to wiring To prevent the unit from tipping forward and provide connections on page 24. In addition to operating power, a stable installation, the unit must be secured in place with the anti-tip bracket provided with the unit. the installer may also be required to supply a home automation system lead to the unit. This is for a low- v
Inhaltszusammenfassung zur Seite Nr. 20
Models 427G and 427RG Installation 20 Anti-Tip Bracket Installation WOOD FLOOR APPLICATIONS INSTALL CONCRETE WEDGE ANCHORS: 1 1 3 Use the six #12 x 2 /2" wood screws and the six /4" flat 1) Drill a /8" (10) diameter hole any depth exceeding the 3 washers provided. Drill pilot holes /16" (5) diameter minimum embedment. Clean the hole or continue maximum, and make sure the screws penetrate through drilling additional depth to accommodate drill fines. the flooring material and into the wall plate a
