Inhaltszusammenfassung zur Seite Nr. 1
Installation
Instructions
For Fully Integrated NoFrost
Combined Refrigerator-Freezers
HC 2062
HCB 2062
HC/HCB 20
7083 319-00
Inhaltszusammenfassung zur Seite Nr. 2
Ianttmpor TO THE INSTALLER PLEASE READ AND FOLLOW It is very important that the guidelines and THESE INSTRUCTIONS instructions are followed in the manual to ensure These instructions contain Warning and Caution proper installation and operation of the unit. The statements. This information is important for safe Installation Guidelines section contains important and efficient installation. information for making sure the installation is correct. Read and understand all the information Al
Inhaltszusammenfassung zur Seite Nr. 3
ItIallanst on GuIdelInes Area Requirements Verify the following: ELECTROCUTION HAZARD • Floors can suppor t refriger ator’ s w eight plus Electrical grounding required. This approximately 1200 pounds (544 kg) of food appliance is equipped with a three-prong weight. (grounding) polarized plug for your protection against possible shock hazards. • Finished kitchen floor height is le v el. Appliance Do not remove the round grounding • must be shimmed level if the floor heigh
Inhaltszusammenfassung zur Seite Nr. 4
p I lann G n ItInforma on Unit Venting - Figure 3 Unit Dimensions - Figure 1 HC/HCB 20 appliances do not require any ventilation openings in the cabinet. The required airflow is directed through the toe kick area. A = 3" (76 mm) B = 79-13/16" (2027 mm) C = 35-13/16" (910 mm) Figure 1 D = 3" (76 mm) E = 24" (610 mm) G = 42-7/16" (1078 mm) H = 37-1/8" (943 mm) Door swing clearence - Figure 2 Please allow for door swing clearance at locations next to a wall. The illustrated measurement is witho
Inhaltszusammenfassung zur Seite Nr. 5
p I lann G n ItInforma on Cabinet Opening Dimensions - Figure 4 Cabinet Inset cabinet Frameless/faceframe cabinet For appliance with panel to be Height C Depth B Depth B flush, adjacent cabinetry depth 80" 24" + panel thickness 24" must equal appliance depth (24") plus panel thickness (5/8" - 3/4"). 84" 24" + panel thickness 24" IMPORTANT Do not install the shut-off valve behind the appliance. The position of the electri- cal outlet is possible within the grey shaded areas or above the a
Inhaltszusammenfassung zur Seite Nr. 6
p lannInG ItInforma on Panel Dimensions - Inset Installation Style - Figure 5 The panels should be at least 5/8 inch (16 mm) Appliance and panels sit fully within the opening thick to allow the connecting rails to be fastened to and are flush with what could be its own box, them. between two pantry cabinets or decorative IMPORTANT columns, etc. This is the most common installation The maximum panel thickness is 3/4" (19 mm). scenario. You can order stainless steel panels for inset installa
Inhaltszusammenfassung zur Seite Nr. 7
p I lann G n ItInforma on Panel Dimensions - Frameless Installation Style - Figure 6 The gap between panels with frameless installation With this installation style, these wider appliance style is 1/4" (6 mm). The panels should be at least panels partially overlay the shared side gables of 5/8 inch (16 mm) thick to allow the connecting rails adjacent cabinetry so as to mimic the look of a to be fastened to them. frameless style cabinet. IMPORTANT The maximum panel thickness is 3/4" (19 mm). C
Inhaltszusammenfassung zur Seite Nr. 8
BI lock G n for s afety Mounting the anti tipping device on concrete floors - Figure 7 - 8 Secure the appliance in place so it does not tip forward when the fully stocked door is opened. The anti tipping bracket is provided with the appliance. Wall 1. Mark the center line of the appliance on the back wall. Align the anti tipping bracket center to this line. Be sure that there is no plumbing or electrical wiring located in this area which Figure 7 screws or drills could damage. 2. Drill a
Inhaltszusammenfassung zur Seite Nr. 9
BI lock nG for s afety Mounting the anti tipping device Cover strips - Figure 12 Before connection to the water supply, the cover in cabinets deeper than 24" - strips provided must be fitted to the appliance. It is Figure 10 - 11 necessary because the appliance will be moved into its recess. To ensure the compressor mounting plate reaches the anti tipping bracket in cabinets deeper than • Remo v e the co v er band from the strips and stic k 24", a wooden spacer must be mount
Inhaltszusammenfassung zur Seite Nr. 10
Ice m aker IceMaker The icemaker for the combined refrigerator-freezer • The solenoid v alv e has a metric is located in the freezer compartment. These R3/4 male connector. A R3/4 instructions only refer to the installation of the ice- (metric) to a 1/4" OD adapter is maker. Please refer to the Use and Care Manual supplied with the ice maker. provided with the appliance for operation instruc- • Inser t the w ater str ainer pro vided tions. The combined refrigerator-freezer mus
Inhaltszusammenfassung zur Seite Nr. 11
Ice m aker 4. Push the appliance slowly to the back wall until the compressor mounting plate makes contact with the anti-tipping bracket (Figure 15). To prevent the appliance from tipping forward the compressor mounting plate must have contact with the anti tipping bracket (Figure 15). Wall Figure 16 Appliance Anti - tipping bracket Compressor mounting plate Figure 15 Figure 17 5. Remove the cover from the valve connector 9. Open the shut-off valve for the water supply and (Figure 16
Inhaltszusammenfassung zur Seite Nr. 12
ItIallanst on Leveling the Appliance - Figure 18 Fasten the appliance in the recess - Figure 20 1. Adjust the height of the appliance at Fasten the appliance in the recess through the the front by twisting upper and lower hinges of the refrigerator doors. the leveling feet 1 Use 2 screws for each hinge. (A/F 27). Use the open-ended spanner provided. 2. Adjust the height of the appliance at the rear by turning the 2 adjusting bolts . 3. Rotate leveling feet 1 until firmly in Figure 1
Inhaltszusammenfassung zur Seite Nr. 13
ItIallanst on Mounting the attachment brackets onto the door panels - Figure 22 Mark lines on the refrigerator door panels as shown in Figure 22. Align the dismounted brackets of the refrigerator doors to the lines on the refrigerator door panels as shown in Figure 22 a. Fasten each bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 mm. Fasten the brackets provided onto the freezer drawer panels using three screws (4 x 16 mm) for each bracket (Figure 22 b). Refrigerat
Inhaltszusammenfassung zur Seite Nr. 14
ItIallanst on Mounting the freezer drawer Mounting the refrigerator door panels - Figure 23 panels - Figures 24 - 33 1. Pull out the upper freezer drawer and screw on The description is for one panel only. The the panel with three screws at left and right hand procedure is the same for both panels. side using the screws as shown in Figure 23. 1. Open the refrigerator door and hang the panel 2. Close the drawer and check the position to the on the adjusting bolts (Figure 24). surrounding ca
Inhaltszusammenfassung zur Seite Nr. 15
ItIallanst on To make it possible to fasten the refrigerator 7. Dismantle the lower attachment bracket from the panel at the bottom the soft-stop cylinder must be refrigerator door. Align the bracket to the lines on dismantled. the refrigerator door panel. (Figure 28). Fasten the bracket with any hole wherever possible using a minimum of 6 screws 4 x 16 5. Grasp the soft-stop cylinder and pull down mm. (Figure 26). The soft-stop cylinder retracts in the detached state. Figure 28 8. Open t
Inhaltszusammenfassung zur Seite Nr. 16
ItIallanst on 10. Move the panel to the left until it makes contact 13. Extend the soft-stop cylinder and connect with with the center rail (Figure 30). the ball stud (Figure 32). 11. Tighten the hex nuts finally. Figure 32 Figure 30 14. Click cover into place (Figure 33). 12. Fasten the refrigerator panel using the same screws that held the lower bracket before removal (Figure 31). Figure 33 Figure 31 16
Inhaltszusammenfassung zur Seite Nr. 17
ItIallanst on Mounting the ventilation grille - Figure 34, 35 1. Pull out the bottom freezer drawer. 2. Remove the blue protection film from the dust filter provided and insert the filter into its opening in the toe kick area as shown in Figure 34. Attach the filter at the bottom, press down the button and click into place. Figure 34 3. Mount the ventilation grille as shown in Figure 35. IMPORTANT Only use the ventilation grille provided with the appliance. This grille is required for prop
