Inhaltszusammenfassung zur Seite Nr. 1
User’s Guide
L1753T
L1953T
L1733TR
L1933TR
L1753TR
L1953TR
L1753TX
L1953TX
Make sure to read the Important Precautions before using the product.
Keep the User's Guide(CD) in an accessible place for furture reference.
See the label attached on the product and give the information to your
dealer when you ask for service.
Inhaltszusammenfassung zur Seite Nr. 2
Important Precautions This unit has been engineered and manufactured to ensure your personal safety, however improper use may result in potential eletrical shock or fire hazards. In order to allow the proper operation of all safeguards incorporated in this display, observe the following basic rules for its installation, use, and servicing. On Safety Use only the power cord supplied with the unit. In case you use another power cord, make sure that it is certified by the applicable national stand
Inhaltszusammenfassung zur Seite Nr. 3
Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord, and do not place the display where the power cord is subject to damage. Do not use this display near water such as near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement, or near a swimming pool. Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation. If these openings are blocked, built-up heat can cause failures wh
Inhaltszusammenfassung zur Seite Nr. 4
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Connecting the stand 1. Place the monitor with its front facing downward on a soft cloth. 2. Assemble the Stand Body into the product in the correct direction as shown in the picture. Make sure you push it until you hear it “click”. Stand Body 3. Assemble the Stand Base(Front, Rear) into the Stand Body in the correct direction. 4. Once assem
Inhaltszusammenfassung zur Seite Nr. 5
Connecting the Display To remove the Stand: 1. Put a cushion or soft cloth on a flat surface. 2. Place the monitor face down on the cushion or soft cloth. The Head part The Stand base part 3. Hold the product as it follows and lift up the Stand slightly. 4. Change your hold on the product as it follows and turn the Stand Base in the arrow direction until you hear a "click." 5. Pull out the Stand to remove. A4
Inhaltszusammenfassung zur Seite Nr. 6
Connecting the Display To remove the Stand Base: 1.Hold the body of the Stand as it 2. Press the two latches at the same follows. time as it follows. 3. Put the Stand Base on a flat surface and 4. The body of the Stand and the Stand pull up the body of the Stand while Base are successfully separated. holding the Stand Base with the other hand. to remove. A5
Inhaltszusammenfassung zur Seite Nr. 7
Connecting the Display Before setting up the monitor, ensure that the power to the monitor, the computer system, and other attached devices is turned off. Positioning your display 1. Adjust the position of the panel in various ways for maximum comfort. Tilt Range: -5˚~20˚ Swivel : 355˚(The feature is not available for all countries) 20 Warning: When adjusting the angle of the screen, do not put your finger in between the head of the monitor and the stand body . You can hurt your finger(s). Ergo
Inhaltszusammenfassung zur Seite Nr. 8
Connecting the Display Using the Computer 1. Place the monitor in a convenient, well-ventilated location near your computer. 1 2. Connect the signal cable . When attached, tighten the thumbscrews to secure the connection. 3. Connect the power cord into a proper power outlet that is easily accessible and close to the display. 2 Power Cord Signal Cable Analog signal Digital signal D-sub DVI Varies according to model. NOTE This is a simplified representation Wall-outlet type of the rear v
Inhaltszusammenfassung zur Seite Nr. 9
Control Panel Functions Side Front Panel Controls Control Function Use this button to enter or exit the On Screen Display. MENU Button OSD LOCKED/UNLOCKED This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear. Use these
Inhaltszusammenfassung zur Seite Nr. 10
Control Panel Functions Control Function Use this button to enter a selection in the On Screen AUTO/SET Display. Button AUTO IMAGE ADJUSTMENT When adjusting your display settings, always press the AUTO/SET button before entering the On Screen Display(OSD). This will automatically adjust your display image to the ideal settings for the current screen resolution size (display mode). The best display mode is 17 inch monitor : 1280 x 1024 19 inch monitor : 1280 x 1024 Power Button Use this button t
Inhaltszusammenfassung zur Seite Nr. 11
On Screen Display (OSD) Control Adjustment Screen Adjustment Making adjustments to the image size, position and operating parameters of the display is quick and easy with the On Screen Display Control system. A short example is given below to familiarize you with the use of the controls. The following section is an outline of the available adjustments and selections you can make using the OSD. NOTE Allow the display to stabilize for at least 30 minutes before making image adjustments. To make a
Inhaltszusammenfassung zur Seite Nr. 12
On Screen Display(OSD) Selection and Adjustment The following table indicates all the On Screen Display control, adjustment, and setting menus. Main menu Sub-menu A D Reference BRIGHTNESS To adjust the brightness, PICTURE contrast and gamma of the CONTRAST screen GAMMA sRGB To customize the color of COLOR PRESET the screen 6500K 9300K RED GREEN BLUE HORIZONTAL To adjust the position of the POSITION screen VERTICAL CLOCK To improve the clarity and TRACKING stability, sha
Inhaltszusammenfassung zur Seite Nr. 13
On Screen Display(OSD) Selection and Adjustment You were introduced to the procedure of selecting and adjusting an item using the OSD system. Listed below are the icons, icon names, and icon descriptions of the all items shown on the Menu. Press the MENU Button, then the main menu of the OSD appears. PICTURE Menu Name Sub-menus Icons Button Tip MENU : Exit : Adjust (Decrease/Increase) SET : Enter : Select another sub-menu NOTE OSD (On Screen Display) menu languages on the monitor
Inhaltszusammenfassung zur Seite Nr. 14
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description PICTURE PICTURE BRIGHTNESS To adjust the brightness of the screen. To adjust the contrast of the screen. CONTRAST GAMMA Set your own gamma value. : -50/0/50 On the monitor, high gamma values display whitish images and low gamma values display high contrast images. MENU : Exit : Decrease : Increase SET : Select another sub-menu COLOR COLOR • sRGB: Set the screen color to fit the PRESET SRGB standard color specificat
Inhaltszusammenfassung zur Seite Nr. 15
On Screen Display(OSD) Selection and Adjustment Main menu Sub menu Description TRACKING TRACKING CLOCK To minimize any vertical bars or stripes visible on the screen background. The horizontal screen size will also change. PHASE To adjust the focus of the display. This item allows you to remove any horizontal noise and clear or sharpen the image of characters. MENU : Exit : Decrease : Increase SHARPNESS To adjust the clearness of the screen. SET : Select another sub-menu SETUP To choose the la
Inhaltszusammenfassung zur Seite Nr. 16
On Screen Display(OSD) Selection and Adjustment The OSD screen will appear when you touch the button on the right side of the monitor. Menu Name Icons Sub-menu Name FLATRON F-ENGINE Screen when applied Screen when not applied When you execute F-ENGINE, two tones will appear on the screen as shown. The applied screen will appear on the left side, whereas the non-applied screen will appear on the right side.Touch the SET button to use the adjusted screen. Main menu Sub menu
Inhaltszusammenfassung zur Seite Nr. 17
Troubleshooting Check the following before calling for service. No image appears No image appears Is the power cord of the • Check and see if the power cord is connected display connected? properly to the power outlet. Is the power indicator • Press the Power button. light on? • Adjust the brightness and the contrast. Is the power on and the power indicator blue or green? Is the power indicator • If the display is in power saving mode, try moving the mouse or pressing any key on the keyb
Inhaltszusammenfassung zur Seite Nr. 18
Troubleshooting Display image is incorrect ● Display Position is • Press the AUTO/SET button to automatically incorrect. adjust your display image to the ideal setting. If the results are unsatisfactory, adjust the image position using the H position and V position icon in the on screen display. • Check Control Panel --> Display --> Settings and see if the frequency or the resolution were changed. If yes, readjust the video card to the recommend resolution. • Press the AUTO/SET button to automa
Inhaltszusammenfassung zur Seite Nr. 19
Troubleshooting Have you installed the display driver? Have you installed the • Be sure to install the display driver from the display driver CD (or diskette) that comes with your display driver? display. Or, you can also download the driver from our web site: http://www.lge.com. • Make sure to check if the video card supports Do you see an Plug&Play function. "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message? A18
Inhaltszusammenfassung zur Seite Nr. 20
Specifications 17 inch Display 17 inches (43.2 cm) Flat Panel Active matrix-TFT LCD Anti-Glare coating 17 inches viewable 0.264 mm pixel pitch Horizontal Freq. Analog : 30 - 83 kHz (Automatic) Sync Input Digital : 30 - 71 kHz (Automatic) Vertical Freq. 56 - 75 Hz (Automatic) Input Form Separate TTL, Positive/Negative SOG (Sync On Green) Digital Video Input Signal Input 15 pin D-Sub Connector DVI - D connector (Digital) Input Fo
