Inhaltszusammenfassung zur Seite Nr. 1
INSTALLATION AND
OPERATING INSTRUCTIONS
REFRIGERATOR FOR LP-GAS AND ELECTRIC OPERATION
RA/RM-1D
FOR YOUR SAFETY
RM2453
If you smell gas:
1. Open windows and door.
RM2553
2. Don’t touch electrical switches.
3. Extinguish any open flame.
4. Immediately call your gas supplier.
FOR YOUR SAFETY
Do not store or use gasoline or other flamma -
ble vapors and liquids in the vicinity of this or
any other appliance.
WARNING
!
Improper installation, adjustment, alteration,
service or maintenance can
Inhaltszusammenfassung zur Seite Nr. 2
CONTENTS INTRODUCTION We are pleased that you have chosen this refrigerator and hope you will derive much satisfaction from using it. REFRIGERATOR OvER IE v w ______________ 3 The refrigerator is designed for storage of foods and storage of frozen foods and making ice. INSTALLATION INSTRUCTIONS ____________ 4 The installation and servicing should only be carried out by Ventilation requirements . . . . . . . . . . . . . .4 . . . . . . an authorized/qualified person and conform to all relevan
Inhaltszusammenfassung zur Seite Nr. 3
REFRIGERATOR OvER vIEw CONTROL PANEL A E D C B OFF OFF ON FUEL SELECTOR FLAME PUSH WHEN LIGHTING THERMOSTAT A. ON/OFF, Fuel selector switch B. Thermostat knob, Gas/Electric C. Flame failure safety valve push-button D. Piezo igniter E. Flame indicator ABSORPTION REFRIGERATOR SySTEM GENERAL ADICE v AND INFORMATION In an absorption refrigerator system, ammonia is liquefied in • Make sure defrosting is carried out periodically the finned condenser coil at the top rear of the refrigerator. • The r
Inhaltszusammenfassung zur Seite Nr. 4
INSTALLATION INSTRUCTIONS The installation, servicing and gas installation must be performed by an authorised/qualified person. The refrigerator must be installed in accordance with the manufacturers installation instructions, local gas fitting regulations, municipal building codes, electrical wiring regulations, AS5601 “Gas Installations” and any other statutory regulations. vENTILATION REUIREMENTS q CLEARANCES The installation shall be made in such a manner as to separate the combustion sys
Inhaltszusammenfassung zur Seite Nr. 5
INSTALLATION INSTRUCTIONS PACKAGING INSTALLING ThE REFRIGERATOR The packaging of this appliance is design to withstand the • The refrigerator must be level, installed on a solid floor transportation from the factory to the point where it will be and in a substantial enclosure. With the vehicle carefully installed in the recreational vehicle. leveled, the refrigrigerator should level both ways in the freezer compartment. Before starting to install the appliance, please, make sure all parts o
Inhaltszusammenfassung zur Seite Nr. 6
INSTALLATION INSTRUCTIONS 2. Two screws installed in the top frame. SECURING ThE REFRIGERATOR - Remove the top decoration panel. After the refrigerator is put in place, (ensuring a combustion - Open the door. seal at the front frame), the refrigerator is to be secured in the - Gently push the tabs out of enclosure with six screws (not included). the hole in the hinge with 2 Please note that failure to follow the sequence in securing the a flat blade screwdriver refrigerator in the enclo
Inhaltszusammenfassung zur Seite Nr. 7
INSTALLATION INSTRUCTIONS 7. No bubbles should appear at the opening of the CONNECTIONS burner jet. The presence of bubbles indicates a de- fective gas safety shutoff, and service is required. LP gas connection If no bubbles were present at the burner jet, the gas The gas installation and servicing must be carried out by an safety valve is working properly. authorised person and conform to all relevant local authori- 8. Rinse jet thoroughly with fresh water before pro- ties. ceeding. Be ca
Inhaltszusammenfassung zur Seite Nr. 8
INSTALLATION INSTRUCTIONS 12 v DC connection ChANGING DOOR SwING The connection is made to the terminal block marked The refrigerator is equipped with a reversible door. A special “12 volts DC heater”, located at the bottom left corner on the door reversing kit must be used to reverse the door. For fur- back of the refrigerator cabinet. ther information, please contact your dealer. The refrigerator must be connected to the battery circuit with two wires of adequate capacity to avoid volt
Inhaltszusammenfassung zur Seite Nr. 9
INSTALLATION INSTRUCTIONS To mount the door panel - snap in 1 REFRIGERATOR REMOv AL 1. Open the door 90 degrees. 1. Disconnect the 230- 240 V AC voltage and 12 V 2 DC voltage leads. 2. Remove the door decoration strip (2) by gently pushing the 2. Shut off the gas supply at the LP tank. four tabs away with a flat blade 3. Disconnect the gas supply line. Always use a screwdriver (1). 2 back up wrench when loosening and tightening 3. Insert the vertical edges connections. into the grooves
Inhaltszusammenfassung zur Seite Nr. 10
OPERATING INSTRUCTIONS GAS AND AC OPERATION REGULATING ThE TEMPERATURE The refrigerator is equipped with a thermostat that can be LP gas operation adjusted by turning the knob B to different setting to maintain the desired cabinet temperature. Before starting the refrigerator, check that all the manual Gas operation gas valves are in the ON position. Do not forget the manual • At “OFF, the thermostat closes its main valve and the shutoff valve on the rear of the refrigerator. burner runs
Inhaltszusammenfassung zur Seite Nr. 11
OPERATING INSTRUCTIONS STORAGE COMPARTMENTS PRODUCT CARE Defrosting WARNING ! 1. Shut off the refrigerator by turning the knob A to “OFF”. Do not store explosive substances in the refrigerator, such as cigarette lighter gas, gasoline, ether or the 2. Empty the refrigerator, leaving the drip tray under like. the finned evaporator. 3. Leave the cabinet and freezer doors open. Filling the ice tray with hot water and placing it on the Food storage compartment freezer shelf can reduce defros
Inhaltszusammenfassung zur Seite Nr. 12
MAINTENANCE & SERvICE Service and maintenance must be done on a regular schedule to keep the refrigerator operating properly, efficiently and safely. The service should only be performed by a qualified technician who is familiar with LP gas systems and refrigerators. Cleaning the flue and burner REPLACING ThE hEATER Inspect the flue baffle. It should be reasonably clean and free The heat necessary for the operation of an absorption cooling of soot. Heavy soot formation indicates improper func
Inhaltszusammenfassung zur Seite Nr. 13
MAINTENANCE & SERvICE 13. Reinstall burner, being careful that the end of the TROUBLEShOOTING burner fits into the slot on the burner bracket. Check to make sure slots are centered under the Refrigerator does not cool properly flue tube and the thermocouple is positioned prop- • Burner jet clogged. erly (tip of thermocouple extends over two slots of • Check level of refrigerator. burner). 14. Be sure to reconnect the wire to high voltage • Venting problem. electrode. Check the electrode f
Inhaltszusammenfassung zur Seite Nr. 14
APPENDIx A - REARvIEw EqUIPMENT Heaters Cover, Flue baffle Terminal block Protection 12Volts 12Volts cover DC DC Heater Reigniter EvaporationTray Screw for protection cover 12 volt terminal block Inlet fitting Burner jet Manual gas Drain water hose Flexible cord shutoff valve 1
Inhaltszusammenfassung zur Seite Nr. 15
APPENDIx B - wIRING DIAGRAM 1
Inhaltszusammenfassung zur Seite Nr. 16
