Inhaltszusammenfassung zur Seite Nr. 1
Inhaltszusammenfassung zur Seite Nr. 2
Preface Firmware Version 1.07 Thank you for choosing DELTA’s high-performance VFD-D D Series. The VFD-DD Series is manufactured with high-quality components and materials and incorporate the latest microprocessor technology available. This manual is to be used for the installation, parameter setting, troubleshooting, and daily maintenance of the AC motor drive. To guarantee safe operation of the equipment, read the following safety guidelines before connecting power to the AC motor drive
Inhaltszusammenfassung zur Seite Nr. 3
Do NOT connect AC main power directly to the drive’s output terminals U/T1, V/T2 and W/T3. DO NOT use Hi-pot test for internal components. The semi-conductor used in the AC motor drive is easily damaged by high-pressure. A charge may still remain in the main circuit terminals with hazardous voltages, even when motor has come to stop. Only the qualified technicians are allowed to install, wire and maintain AC motor drive. Be aware of the motor that it may rotates as soon as th
Inhaltszusammenfassung zur Seite Nr. 4
without prior notice. Please contact your local distributors or visit our website to download the most updated version at http://www.delta.com.tw/industrialautomation/. The AC motor drive may also be called as “drive”, all drive mentioned in this manual refers to the AC motor drive.
Inhaltszusammenfassung zur Seite Nr. 5
Table of Content Chapter 1 Introduction 1-1 Receiving and Inspection ....................................................................................................1 - 2 1-2 Preparation for Installation and Wiring ...............................................................................1-4 1-3 Dimensions ....................................................................................................................... 1 - 6 Chapter 2 Wiring 2-1 Wiring Diagram ............
Inhaltszusammenfassung zur Seite Nr. 6
Group 04: Door Open Parameters ..................................................................................4-42 Group 05: Door Close Parameter....................................................................................4 -46 Group 06: Protection and Special Parameters.................................................................4 -51 Group 07: Control Parameters ........................................................................................4 -57 Group 08: Multi-step
Inhaltszusammenfassung zur Seite Nr. 7
Chapter 1 Introduction |DD Series Chapter 1 Introduction 1-1 Receiving and Inspection 1-2 Preparation for Installation and Wiring 1-3 Dimensions The AC motor drive should be kept in the shipping carton or crate before installation. In order to retain the warranty coverage, the AC motor drive should be stored properly when it is not to be used for an extended period of time. Storage conditions are: Store in a clean and dry location free from direct sunlight or corrosive fumes. Sto
Inhaltszusammenfassung zur Seite Nr. 8
Chapter 1 Introduction |DD Series 1-1 Receiving and Inspection This VFD-VL AC motor drive has gone through rigorous quality control tests at the factory before shipment. After receiving the AC motor drive, please check for the following: Check to make sure that the package includes an AC motor drive, the User Manual/Quick Start and CD. Inspect the unit to assure it was not damaged during shipment. Make sure that the part number indicated on the nameplate corresponds with the part numb
Inhaltszusammenfassung zur Seite Nr. 9
Chapter 1 Introduction |DD Series Explanation for Series Number 0 02DD21A0 T 33 Production number Production week Production year 2007 Production factory (T: Taoyuan, W: Wujian) 230V 1-PHASE 0.25HP(0.2kW) Model 1-3
Inhaltszusammenfassung zur Seite Nr. 10
Chapter 1 Introduction |DD Series 1-2 Preparation for Installation and Wiring Install the AC motor drive in an environment with the following conditions: -10 ~ +45°C (14 ~ 113°F) Air Temperature: Relative Humidity: <90%, no condensation allowed Atmosphere pressure: 86 ~ 106 kPa Operation Installation Site <1000m Altitude: 2 <20Hz: 9.80 m/s (1G) max Vibration: 2 20 ~ 50Hz: 5.88 m/s (0.6G) max Temperature: -20°C ~ +60°C (-4°F ~ 140°F) Relative Humidity: <90%, no condensation allowed
Inhaltszusammenfassung zur Seite Nr. 11
Chapter 1 Introduction |DD Series CAUTION! 1. Mount the AC motor drive vertically on a flat vertical surface by using bolts or screws. Other directions are not allowed. 2. The AC motor drive will generate heat during operation. Allow sufficient space around the unit for heat dissipation. When the AC motor drive is installed in a confined space (e.g. cabinet), the surrounding temperature must be with good ventilation. DO NOT install the AC motor drive in a space with bad ventilation. 3.
Inhaltszusammenfassung zur Seite Nr. 12
Chapter 1 Introduction |DD Series 1-3 Dimension VFD002DD21A; VFD002DDDD21AB; VFD002DD21C; VFD002DD21CB; VFD004DD21A; VFD004DD21AB; VFD004DD21C; VFD004DD21CB; VFD002DD21E; VFD004DD21E; Unit: mm [inch] W W1 W2 H H1 H2 H3 H4 D D1 Φ1 Φ2 215.0 204.0 204.0 170.0 138.5 15.0 15.1 15.5 55.0 8.5 5.0 7.0 [8.46] [8.03] [8.03] [6.69] [5.45] [0.59] [0.59] [0.61] [2.17] [0.34] [0.20] [0.28] Dimensions for Motor ECMD-B9120GMS 1-6
Inhaltszusammenfassung zur Seite Nr. 13
Chapter 1 Introduction |DD Series ECMD-B9160GMS 1-7
Inhaltszusammenfassung zur Seite Nr. 14
Chapter 2 Wiring |DD Series Chapter 2 Wiring After removing the front cover, examine if the power and control terminals are clearly noted. Please read following precautions before wiring. Make sure that power is only applied to the R/L1, S/L2, T/L3 terminals. Failure to comply may result in damage to the equipments. The voltage and current should lie within the range as indicated on the nameplate (Chapter 1-1). All the units must be grounded directly to a common ground terminal to prev
Inhaltszusammenfassung zur Seite Nr. 15
Chapter 2 Wiring DD Series 2-1 Wiring Diagram When wiring for an AC motor drive, user needs to connect wires to two sections, main circuit and control circuit. Please properly connect wires to your AC motor drive according to the circuit diagram provide in the following pages VFD-DD Basic Wiring Diagram *1 GND Induction motor: A, B, +5V, GND B A Z- Z +5V Permanent magnet motor: A, B, Z, Z-, +5V, GND +12V 2-2 5 43 2 1 9 8 7 6
Inhaltszusammenfassung zur Seite Nr. 16
Chapter 2 Wiring |DD Series Wiring/Terminals Setting Used with internal power (+24Vdc) Used with external power MI1 MI1 MI2 MI2 MI5 MI5 COM +24V + COM +24V External +24V power COM CAUTION! The wiring of main circuit and control circuit should be separated to prevent erroneous actions. Please use shield wire for the control wiring and not to expose the peeled-off net in front of the terminal. Please use the shield wire or tube for the power wiring and ground the two ends of the shiel
Inhaltszusammenfassung zur Seite Nr. 17
Chapter 2 Wiring |DD Series Damaged insulation of wiring may cause personal injury or damage to circuits/equipment if it comes in contact with high voltage. The AC motor drive, motor and wiring may cause interference. To prevent the equipment damage, please take care of the erroneous actions of the surrounding sensors and the equipment. The AC drive output terminals U/T1, V/T2, and W/T3 should connect to the motor terminals U/T1, V/T2, and W/T3 respectively. To reverse the direction of
Inhaltszusammenfassung zur Seite Nr. 18
Chapter 2 Wiring |DD Series 2-2 Main Circuit Terminal Main Circuit Terminal Motor L1 L1 U/T1 L2 L2 V/T2 IM/PM E W/T3 E Wire Gauge Torque Wire Type 14-12 AWG. Stranded copper only，75℃ 5.2kgf-cm (4.5in-lbf) 2 (2.075-3.332mm ) Terminal Symbol Explanation of Terminal Functions L1, L2 AC line input terminals U/T1, V/T2, W/T3 AC drive output terminals for connecting 3-phase induction motor E Earth connection, please comply with local regulations. Mains power terminals： Power can
Inhaltszusammenfassung zur Seite Nr. 19
Chapter 2 Wiring |DD Series (Resistance-Capacitance), unless approved by Delta. DO NOT connect phase-compensation capacitors or surge absorbers at the output terminals of AC motor drives. Use a well-insulated motor, suitable for inverter operation. 2-6
Inhaltszusammenfassung zur Seite Nr. 20
Chapter 2 Wiring DD Series 2-3 Control Circuit Terminal DCM COM 24V OD CD MI5 MI4 MI3 MI2 MI1 MCM MO3 MO2 MO1 RC2 RB2 RC1 RA1 RB1 RA2 Torque Wire Gauge 2 5 kgf-com (6.9 in-lbf) 18-12 AWG (0.8107-3.332mm ) Terminal Terminal Function Factory Setting (NPN Mode) Symbol OD-DCM: ON: Open ; OFF: Decelerate to stop OD Door Open to Stop CD-DCM: ON: Close; OFF: Decelerate to stop CD Door Close to Stop MI1 Multi-function Input 1 Refer to Pr. 02-01~02-05 for programming of Multi-f
