Inhaltszusammenfassung zur Seite Nr. 1
PRODUCT GUIDE
MODEL 463247310
I N F R A R E D
I N F R A R E D
IMPORTANT: Fill out the product record information below.
Serial Number
See rating label on grill for serial number.
Date Purchased
For support and to register your
grill, please visit us at
www.charbroil.com
If you have questions or need
assistance during assembly,
please call 1-888-430-7870.
Estimated assembly time: 30 minutes
The following are trademarks registered by W.C. Bradley Co. in the U.S. Patent and Trademark Office: Ca
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS DANGER For Your Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2-3 If you smell gas: Use and Care . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4-10 Limited Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 1. Shut off gas to the appliance. Parts List. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 2. Extinguish any open flame. 3. Open lid. Parts Dia
Inhaltszusammenfassung zur Seite Nr. 3
WARNING CAUTION CALIFORNIA PROPOSITION 65 Using pots larger than 6 quarts in capacity could 1. Combustion by-products produced when using exceed weight limit of the this product contain chemicals known to the State of side burner shelf or side shelf, California to cause cancer, birth defects, and other reproductive harm. resulting in failure 2. This product contains chemicals, including lead of grill cart components. and lead compounds, known to the State of California to cause cancer, birth
Inhaltszusammenfassung zur Seite Nr. 4
LP Cylinder USE AND CARE • The LP cylinder used with your grill must meet the following requirements: • Use LP cylinders only with these required measurements: 12" DANGER (30.5cm) (diameter) x 18" (45.7 cm) (tall) with 20 lb. (9 kg.) capacity maximum. • NEVER store a spare LP cylinder under or near • LP cylinders must be constructed and marked in accordance the appliance or in an enclosed area. with specifications for LP cylinders of the U.S. Department of Transportation (DOT) or for C
Inhaltszusammenfassung zur Seite Nr. 5
e s i w k LP Cylinder Exchange Connecting Regulator to the LP Cylinder •Many retailers that sell grills offer you the option of replacing 1.LP cylinder must be properly secured onto grill. (Refer to your empty LP cylinder through an exchange service. Use only assembly section.) those reputable exchange companies that inspect, precision fill, 2.Turn all control knobs to the OFF position. test and certify their cylinders. Exchange your cylinder only for an OPD safety feature-equipped cylinder
Inhaltszusammenfassung zur Seite Nr. 6
Straight Leak Testing Valves, Hose and Regulator 1. Turn all grill control knobs to OFF. 2. Be sure regulator is tightly connected to LP cylinder. 3. Completely open LP cylinder valve by turning hand wheel counterclockwise. If you hear a rushing sound, turn gas off immediately. There is a major leak at the connection. Correct before proceeding. 4. Brush soapy solution onto areas circled below, or other similar Hold coupling nut and regulator fittings on your grill. as shown for proper connect
Inhaltszusammenfassung zur Seite Nr. 7
Safety Tips Before opening LP cylinder valve, check the coupling nut for WARNING tightness. When grill is not in use, turn off all control knobs and LP cylinder valve. For Safe Use of Your Grill and to Avoid Serious Never move grill while in operation or still hot. Injury: Use long-handled barbecue utensils and oven mitts to avoid • Do not let children operate or play near grill. burns and splatters. Maximum load for sideburner and side shelf is 10 lbs. • Keep grill area clear an
Inhaltszusammenfassung zur Seite Nr. 8
Burner Flame Check • Remove cooking grates and flame tamers. Light burners, rotate WARNING knobs from HI to LOW. You should see a smaller flame in LOW position than seen on HI. Perform burner flame check Turn controls and gas source or tank OFF when not on sideburner, also. Always check flame prior to each use. If in use. only low flame is seen refer to "Sudden drop or low flame" in the Troubleshooting Section. HI CAUTION LOW If ignition does NOT occur in 5 seconds, turn the burner contr
Inhaltszusammenfassung zur Seite Nr. 9
General Grill Cleaning • Do not mistake brown or black accumulation of grease and CAUTION smoke for paint. Interiors of gas grills are not painted at the factory (and should never be painted). Apply a strong solution of detergent and water or use a grill cleaner with scrub brush SPIDER ALERT! on insides of grill lid and bottom. Rinse and allow to completely air dry. Do not apply a caustic grill/oven cleaner to painted surfaces. SPIDER AND WEBS • Plastic parts: Wash with warm soapy water
Inhaltszusammenfassung zur Seite Nr. 10
Cleaning the Burner Assembly (C) Wear eye protection: Use an air hose to force air into Follow these instructions to clean and/or replace parts of burner the burner tube and out the burner ports. Check each assembly or if you have trouble igniting grill. port to make sure air comes out each hole. 1. Turn gas off at control knobs and LP cylinder. 6. Wire brush entire outer surface of burner to remove food 2. Remove cooking grates and flame tamers. residue and dirt. 3. Remove carryover tubes a
Inhaltszusammenfassung zur Seite Nr. 11
LIMITED WARRANTY This warranty only applies to units purchased from an authorized retailer. Manufacturer warrants to the original consumer-purchaser only that this product shall be free from defects in workmanship and materials after correct assembly and under normal and reasonable home use for the periods indicated below beginning on the date of purchase*. The manufacturer reserves the right to require that defective parts be returned, postage and or freight pre-paid by the consumer for re
Inhaltszusammenfassung zur Seite Nr. 12
PARTS LIST Key Qty Description Key Qty Description A 1 BOTTOMSHELF MM 1 GRILLTOPLID B 2 CASTER,LOCKING NN 1 INNERINSERT,F/TOPLID C 2 CASTER,FIXED OO 1 HANDLEF/TOPLID D 1 CARTLEFTSIDEPANEL PP 2 BEZEL,F/LIDHANDLE E 1 GROMMET RECTANGULARBUMPER,F/ QQ 2 F 1 CARTRIGHTSIDEPANEL TOPLID G 1 LOWERBACKPANEL RR 1 LOGOPLATE H 1 TANKEXCLUSION SS 1 HARDWAREF/TOPLID I 1 DOORBRACE TT 1 DOORLEFT,NOHANDLES J 1 HEATSHIELD,F/TANK UU 3 HANDLEF/DOOR,SBLID K 1 LEFTRAIL,F/GREASETRAY VV 1 DOORRIGHT,NOHANDLES L 1 RIGHTRAI
Inhaltszusammenfassung zur Seite Nr. 13
PARTS DIAGRAM MM SS NN PP RR PP QQ OO AAA ZZ GG UU L K YY BBB BB P P HH J XX WW O O Q II O KK FF M S X JJ LL CC FFF GGG EE T AA Z EEE N UU Y UU R TT Z VV E V I H G W DD U DDD D F A HHH CCC C B C B 13
Inhaltszusammenfassung zur Seite Nr. 14
Front Front ASSEMBLY casters at the front. and the two fixed Attach the two locking casters at the rear of the bottom shelf 1 Use the provided caster wrench to fully tighten casters. Fixed caster Locking caster Bottom shelf Rear Attach side panels to bottom shelf using three 2 1/4-20x1/2” screw 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers per panel. IMPORTANT: Panel with large hole must 7mm lock washer be on Right side of bottom shelf. 7mm flat washer Left side panel Make sure
Inhaltszusammenfassung zur Seite Nr. 15
Place lower back panel between side panels at rear of bottom shelf. Make sure the slots are positioned as shown (A). Secure 3 lower back panel to side panels using two 1/4-20x1/2” screws, 7mm lock washers, and 7mm flat washers on each side. 1/4-20x1/2” screw 7mm lock washer 7mm flat washer Lower back panel The vertical flange should be on left side when the lower back panel is properly A installed Vertical flange This step requires two people 4 to lift and position grill head onto cart. Car
Inhaltszusammenfassung zur Seite Nr. 16
Lower back panel Release the cap and nut from electronic ignition module. Attach electronic ignition module and heat shield to the cart right 5 side panel with the nut and cap. Heat Shield Nut Electronic ignition module Cap NOTE: Parts and wires omitted for clarity of illustration On back of grill, place upper back panel between side panels and above lower back panel. Secure upper back panel, in lower holes, using one 6 1/4-20x1½” screw, 7mm lock washer, and 7mm flat washer on each side. D
Inhaltszusammenfassung zur Seite Nr. 17
Insert flange on right side shelf into side shelf brackets on side of firebox, shown A. Attach rear of shelf using one 1/4-20x3/4” screw, 7mm lock washer, 7mm 7 flat washer and 1/4”nut in upper hole; using one 1/4-20x1½” screw, lock washer and 7mm 7mm flat washer in lower hole, shown B/C. Attach front of shelf and fascia using screws, two 1/4-20x3/4” 7mm flat washers, 7mm lock washers and1/4”nuts, and one #8x3/8” self-tapping screw with large washer, shown C/D/E. A 7mm lock C B Rear of Sh
Inhaltszusammenfassung zur Seite Nr. 18
Remove the four screws and washers factory attached to the Auto Clean valve bracket. Position Auto Clean valve bracket 8 beneath right side shelf fascia so that valve stem comes through larger center hole in fascia. Align the four holes on valve bracket with the four holes on fascia. Secure using screws and washers that were removed from bracket, shown A. Place the blank bezel over valve stem on front side of the fascia. Align small holes on bezel with the holes on fascia. Attach using two #8-3
Inhaltszusammenfassung zur Seite Nr. 19
Insert tabs on left sideburner shelf assembly into rectangular slots in side of firebox, shown A. 9 Attach rear of shelf using one 1/4-20x3/4” screw, 7mm flat washer,7mm lock washer and 1/4”nut in upper hole; and using 1/4-20x1½” screw, 7mm lock washer, 7mm flat washer in lower hole, shown B/C. Attach front of shelf and fascia using two 1/4-20x3/4” screws, 7mm flat washers, 7mm lock washers and 1/4”nuts, and one #8x3/8” self-tapping screw with large washer, shown C/D/E. Now you may fully tig
Inhaltszusammenfassung zur Seite Nr. 20
Insert front brace under control panel and between cart side panels. Make sure door hinge pins are on the top side and 10 facing the front. Secure using two 1/4-20x1½” screws, 7mm lock washers, and 7mm flat washers on each side. NOTE: MAKE SURE THAT THE FRONT BRACE IS MOUNTED IN THE MOST DOWNWARD POSITION WHEN ASSEMBLED TO CART. 1/4-20x1½” 7mm flat screw 7mm lock washer washer First, remove the two screws and lock washers factory attached to the sideburner valve bracket. Position sideburner 1
