Bedienungsanleitung Clam Corp Fish Trap 8062

Inhaltszusammenfassung zur Seite Nr. 1

Model No.
- 8062 -
p/n 108324

Specifications
Height: 70” (24” packed)
▪
Width: 65”
▪
▪ Depth: 86” (38” packed)
Weight: 107 lbs.
▪
Instruction p/n 102478
▪















- Cla m Cu s to m er S e rv ic e I n fo rm at io n -

NOTICE!! Once used, this shelter cannot be returned to the store. If you have a
warranty claim, have your sales receipt ready and contact Clam Corporation
Customer Service by email inquiry or direct by calling:
Customer Service Hrs: - 9am

Inhaltszusammenfassung zur Seite Nr. 2

- Parts Li st - ITEM NO. PART NUMBER DESCRIPTION QTY. 1 101580 REAR ADJUSTABLE SPREADER POLE 1 2 101431 TUBE, YUKON CANOPY HOOP 3 3 101148 SCREW, #6 X 0.38 16 4 101481 ROOF SPREADER POLE 2 5 101095 ROPE, 3/8 DIA X 9 FT 1 6 101584 BRKT, LEFT CANOPY 1 7 101088 SCREW, 1/4-20 X 0.75 6 8 101167 FRONT ADJUSTABLE SPREADER POLE 2 9 101083 CAP, TUBE SPACER 8 10 101470 SCREW, 1/4-20 X 0.50 16 11 101146 CHANNEL, 8.78 ALUM EXT 4 12 101652 TUBE, 20.00 SEAT RAIL 4 13 101486 SCREW, 1/4-2

Inhaltszusammenfassung zur Seite Nr. 3

- Parts Di agram - 3

Inhaltszusammenfassung zur Seite Nr. 4

- Step One - 4

Inhaltszusammenfassung zur Seite Nr. 5

- Step Two - 5

Inhaltszusammenfassung zur Seite Nr. 6

- Step Three - 6

Inhaltszusammenfassung zur Seite Nr. 7

- Step Four - 7

Inhaltszusammenfassung zur Seite Nr. 8

- St ep Five - Rear Seat Bracket (p/n 102430) Latch Clip (p/n 102512) 8

Inhaltszusammenfassung zur Seite Nr. 9

- Step Si x - Yukon Base (p/n 102497) 1”x2” Rectangular Support Tube (p/n 102503) 9

Inhaltszusammenfassung zur Seite Nr. 10

- Step Seven - Slide the canopy hoop poles onto the canopy poles until the spring buttons engage the holes near the ends of each canopy hoop pole. Support the first canopy hoop pole as pictured with the rear adjustable spreader poles (the shorter of the two provided lengths). Lean the two remaining canopy hoop poles against the first. 10

Inhaltszusammenfassung zur Seite Nr. 11

- Step Ei ght - Drape the tent over the supported hoops then go inside and spread out the canopy hoop poles, attaching the roof velcro as you go. Orient the porch hoop pole so that the holes face upward and then feed the length of the pole through the three porch hoop sleeves sewn on the Tent. Slide the porch hoop pole onto the porch poles, engaging the second hole position. Attach the porch hoop velcro on each side of the tent. Remove the rear adjustable spreader poles now suppor

Inhaltszusammenfassung zur Seite Nr. 12

- Step Nine - To “ set” the tent, grasp the tent material at the rear of the shelter and pull it downward. Observe the porch area of the tent lifting accordingly as you pull. When the U-Channel molding is correctly installed, the porch hoop pole will lightly touch the floor. To achieve this condition, start by finding the center of the molding. From behind the unit, pull the midpoint of the tent downward and fold the tent material under the base lip. Press the midpoint of the molding

Inhaltszusammenfassung zur Seite Nr. 13

- Step Ten - Angle the seat assembly slightly while placing the bottom lip of the front seat bracket under the outside edge of the base lip. Tilt the complete assembly downward so that the rear seat bracket lands upon the support tube. Reach under the rear seat bracket and slide the latch clip outwards and then up against the underside of the support tube. Squeeze the latch clip into the horizontal slot of the rear seat bracket. Secure the position of the latch clip by pushing it

Inhaltszusammenfassung zur Seite Nr. 14

- Tips for Use - Folding and transporting your Fish Trap is easy: Unsnap the roof spreader poles, rear spreader poles, and front spreader poles. Lay them in the bottom ▪ of the base. ▪ Push the spring buttons and retract each hoop, starting with the rear hoop and working towards the front. Rotate all retracted hoops to the resting position. Tuck the tent into the base and between the hoops so that no material is left hanging on the ground for transport. Cover with the Travel Cover* (