Inhaltszusammenfassung zur Seite Nr. 1
EZ-777 TW1 /EZ-777 TW2 / EZ-777 FM
2-Way Paging Remote Engine Starting & Keyless
Entry System with 1-Way Sidekick Remote Control
OPERATING INSTRUCTIONS
-PRIMARY: These are features that must be connected in order for the system to operate properly i.e. Remote
Start connections, Flashing lights, Brake Reset. For programming, the hood pin and program button are required.
-OPTIONAL: These are features are to be connected only if desired or agreed upon by the customer and the
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS Operation Cautions & Warnings….………………..….…………………………………….………………….………1 2-Way Paging LED Remote TW1.........…………………………………………………………….………………….2 2-Way Paging LCD Remote TW2..…………………………………………………………………………………….3 2-Way Paging LCD Remote FM…..……..………………………………………………………………………...…..4 Using the Remote 1-Way Remote…………………………………………………………………………….………..5 Remote Engine Starting………………………………………………………………………………………….……6-8 Turbo Timer Mode……………………………….……………………………………...…………………………….…9 Convenience
Inhaltszusammenfassung zur Seite Nr. 3
2-WAY PAGING LED REMOTE EZ-777.TW1 OPERATION: FIXED BUTTON 1 (Lock Symbol): ANTENNA • Press and release to Lock doors. • Press and Hold for more than 3 seconds to activate “Panic” feature. BUTTON 2 (Unlock Symbol): PAGING • Press and release to Unlock doors. LED's BUTTON 3 (Trunk Symbol): • Press and Hold for two seconds to activate #2 #1 trunk pop (Optional Feature). UNLOCK LOCK BUTTON 4 (Start): • Press and Hold for two seco
Inhaltszusammenfassung zur Seite Nr. 4
2-WAY PAGING LCD REMOTE EZ-777.TW2 OPERATION: FIXED BUTTON 1 (LOCK Symbol): ANTENNA • Press and release to Lock doors. #2 UNLOCK • Press and Hold for more than 3 seconds to activate “Panic” #1 LOCK feature. BUTTON 2 (Unlock Symbol): • Press and release to Unlock doors. AM BUTTON 3 (Trunk Symbol): #5 RECALL • Press and Hold two seconds to activate trunk pop (Optional LCD CAR I or II Feature). SCREEN BUTTON 4 (Start Key Symbol):
Inhaltszusammenfassung zur Seite Nr. 5
2-WAY PAGING LCD REMOTE EZ-777.FM OPERATION: BUTTON 1 (Lock Symbol): FIXED • Press and release to Lock system. ANTENNA Press and Hold for more than 3 seconds to activate “Panic” feature. BUTTON 2 (Unlock Symbol): LCD • Press and release to Unlock system. SCREEN PM BUTTON 3 (Trunk Symbol): #5 RECALL / • Press and Release to activate trunk pop (Optional CAR I OR II Feature). #2 DISARM/ UNLOCK BUTTON 4 (Start Symbol): #1 ARM/ • Press and release to Start/Stop Engine. L
Inhaltszusammenfassung zur Seite Nr. 6
USING THE 1-WAY REMOTE The transmitter supplied with the EZ-777 system #2 has six buttons. The button configuration of the EZ- UNLOCK 777 is Factory-set and unchangeable. See Page 13 for additional information on how to use your remote #1 to operate a second vehicle equipped with an EZ- #5 LOCK 777 system. FLASHLIGHT NOTE: BUTTON #4 Remote Start #6 (FM only) There is a deliberate delay built into the system on #3 button #4 to help prevent accidental remote starting VEHICLE 2 TRUNK
Inhaltszusammenfassung zur Seite Nr. 7
REMOTE ENGINE STARTING REMOTE ENGINE STARTING - UNSUCCESSFUL START In the event that the engine does not start on the first attempt, the system shuts down for a few seconds, then nd rd attempts to restart the engine a 2 and 3 time. For hard starting engines, the unit will allow a starter crank time of up to 10 seconds maximum. This should provide ample cranking time for difficult starts, but is limited to 13 seconds to help prevent damage to the starter from over cranking. nd rd 1) If
Inhaltszusammenfassung zur Seite Nr. 8
REMOTE ENGINE STARTING IDLE DOWN MODE - EXITING THE VEHICLE: 1) With vehicle engine running with key, press the Remote Start button for at least one second. 2) Parking Lights will turn ON. 3) Doors will unlock, or if brake pedal is being depressed, doors will unlock when it is released. 4) Turn OFF Ignition and remove key. Engine should remain running. 5) Exit vehicle then remote lock doors if desired. 6) Engine will remain running for programmed run time or until you return (whichever
Inhaltszusammenfassung zur Seite Nr. 9
REMOTE ENGINE STARTING INFINITY RUN MODE – EXITING THE VEHICLE: 1) With vehicle engine running with the key, press the Remote Start button for at least 1 second, pause a few seconds, then press and release the remote start button a second time. 2) Parking Lights will start flashing, and doors will unlock. 3) Turn Ignition switch OFF, remove key and exit the vehicle. Engine should remain running. 4) The vehicle’s parking lights will flash for the programmed run time of 12, 24, or 36, or
Inhaltszusammenfassung zur Seite Nr. 10
TURBO TIMER MODE (OPTIONAL) The optional Turbo Timer mode allows the CoolStart system to keep a Turbo or Turbo Diesel vehicle running for 1 to 5 minutes [selectively] after you remove the key, exit the vehicle, and lock the doors remotely. This is handy for turbo cool-down without the need for expensive turbo timers. This mode requires the use of an extra part called a momentary switch/button that is not included with the kit. Check with your installer about adding this feature. NOTE
Inhaltszusammenfassung zur Seite Nr. 11
CONVENIENCE AND SAFETY FEATURES KEYLESS ENTRY (POWER DOOR LOCK CONTROL, Optional) This system enables you to remotely lock and unlock the vehicle’s doors (if equipped with power locks) via remote control for safety and convenience. Note: This feature may require extra labor and/or parts to install. Press the Lock or Unlock transmitter button as you leave or come near the vehicle. Parking lights will flash once for lock and twice for unlock. If vehicle is running by the remote start sy
Inhaltszusammenfassung zur Seite Nr. 12
CONVENIENCE AND SAFETY FEATURES VALET MODE / STARTER DISABLE OVERRIDE Before servicing your vehicle or handing the keys over to a Valet we recommend putting the unit into valet mode. The remote start function WILL NOT operate when in Valet mode. To enter Valet mode, turn the key to the ON position, press and hold Program/Valet switch for 5-6 seconds. The LED will turn on solid and the system is now in valet. Perform this procedure again to exit of Valet mode. The keyless entry will s
Inhaltszusammenfassung zur Seite Nr. 13
TRANSMITTER PROGRAMMING Note: All transmitter codes must be learned at time of programming!! The EZ-777 learns up to 4 different transmitter codes. 1. Open Hood (If no hood pin installed with your system, then you must ground the Gray Hood pin wire). 2. Turn key to the ON position. 3. Press Programming button 4 times, then after a few seconds the unit flashes the parking lights 4 times. 4. Press button #1 & #2 together of the transmitter to be coded. You should get 2 light flash
Inhaltszusammenfassung zur Seite Nr. 14
2-VEHICLE OPERATION A single EZ-777FM remote can control two different vehicles with EZ-777FM systems installed. However, both systems must be the same type. EZ-777TW1 is not compatible with EZ-777FM. SETUP: VEHICLE #2 Follow the “Transmitter Programming” steps on the second Press side button vehicle. Program Car #2’s existing remotes, then quickly press the Car #2 side button on your remote before first, then you have pressing the lock button on your remote to program it to 4 secon
Inhaltszusammenfassung zur Seite Nr. 15
TROUBLESHOOTING cont. UNIT CRANKS VEHICLE BUT ENGINE NEVER STARTS: (2 parts) 1. In extreme cold or severe weather conditions, the unit may take more than the first attempt to start the vehicle. The remote start unit will make up to 3 attempts to start the engine. 2. In some vehicles, there may be a Factory anti-theft system that will not allow the engine to run without the key in the ignition. These systems may include Factory Security Modules, GM Passkey®/Passlock®, and RF Transponder
Inhaltszusammenfassung zur Seite Nr. 16
SETTING THE CLOCK (2-WAY- LCD REMOTE) EZ-777 TW2 1. Press the Recall button #5 on the side of the remote control 5 times. 2. The remote will beep and the AM or PM display will begin flashing. 3. Press the Lock button #1 to increase time. 4. Press the Unlock button #2 to decrease time. 5. Press the Trunk button #3 to go to the next item – AM - PM - Hour- Minutes. 6. Press the Start button #4 to Disable or Enable Beep. 7. Press the Recall button #5 to Exit Setup or wait 7 seconds, the L
