Inhaltszusammenfassung zur Seite Nr. 1
MTK Kit:
Honda K Series
Engine Conversions
for Classic Minis
MTK Installation Manual
For Classic Minis 1959 – 2001
Inhaltszusammenfassung zur Seite Nr. 2
Dear Customer, We welcome you to the Honda Powered Mini World. Thank you and Congratulations for your purchase. You can be certain that you have made a wise choice with this upgrade. This kit was designed to help put you on the right track when building your ultimate Mini. With the help of this MTK Kit, you will be driving your Super Fast Mini soon. Mini has been made in many variations with many subtle “tweaks” and varying build quality over its lifetime. It is impossible to account fo
Inhaltszusammenfassung zur Seite Nr. 3
MTK Contents This Section contains a list and description of the parts included in the MTK Kit, and a list of parts that you will need in addition to the MTK Kit. MTK Kit Includes: - MTK Subframe - Engine Mounting Spacer (2) - Upper Suspension Arms - Transmission Adaptor Bracket - Adjustable Lower Suspension Arms - Lower Cross Member - Rear Transmission Stabilizer - Extended Steering Arms - Front Stabilizer Bar - Mounting Hardware - Engine Mounting Bracket - 2 Mini/Honda Chromoly A
Inhaltszusammenfassung zur Seite Nr. 4
Additional Parts Needed: - Honda K series engine/transmission (See List on pages 15 and 16) - Coil-over shocks (#511200) - Front disc brake system such as; Mini Tec’s Superbrakes, Mini 8.4” disc brakes, other… - Wheels with a –7mm offset to the outside (needed for turning radius clearance) or 1” wheel spacers - Honda engine, ECU, and dash wiring harness’ - Modified Honda ECU or engine management system - Electronic speedometer: a mechanically driven Mini speedometer will not w
Inhaltszusammenfassung zur Seite Nr. 5
Preparation Step 1: Remove stock Mini engine and subframe from Mini. Then remove everything else in the engine compartment. Step 2: Whether you use Mini Tec’s MT Flip Front End Kit or you do an extension yourself, you will need to cut existing Mini front end after the a-panel seem to remove existing Mini front. See Figure 1-2. Note: For extended metal front ends, it is best to attach the MTK subframe first before performing any body extensions. 5
Inhaltszusammenfassung zur Seite Nr. 6
Step 3: Clean, Prepare, and Prime the cars firewall and all ruff surfaces (See Figure 1-3). Note: Add additional metal for extra stiffness to the front side of the a-panel as shown in the photo below. A guide tab on the inside of the a-panel will help align the MT Flip Front End as it closes. 6
Inhaltszusammenfassung zur Seite Nr. 7
Step 3: Cut out metal just below stock shock mount. This is needed to fit the MTK subframe (See following two photos). Your Mini should now be prepared for the installation process. 7
Inhaltszusammenfassung zur Seite Nr. 8
Subframe assembly *Supplied with kit Step 1: Attach upper bump stops. Mini bump stops with the single stud will work here. Step 2: Attach the subframe to the car using the two large subframe mounting bolts just like the standard Mini subframe. If your car is an earlier model and does not have these two large ¾” diameter bolts, then you will need Mini Tec’s MK1/2 Subframe Mounting Kit (#351000). Standard Mini mounting bolts are circled in red in the following photo. Do not tighte
Inhaltszusammenfassung zur Seite Nr. 9
Step 3: Drill six holes to support the bottom of the subframe using a 5/16” drill bit. Use the six supplied 5/16” bolts with plates to fasten the subframe to the car on the lower side. The plates will go inside of the car to give the floor panel extra support. After the six bolts are in place and tightened, tighten the two large subframe mounting bolts on top of the frame. See photos. Your subframe should now be attached to your Mini. 9
Inhaltszusammenfassung zur Seite Nr. 10
Installing Engine into Subframe: Step 1: Drill stock B Series Honda engine and transmission mounts to ½”. Step 2: Attach supplied transmission mount adaptor plate using the supplied hardware in the sequence that it is attached to the plate. Then attach Honda B Series transmission mount to transmission. Step 3: Attach Honda B Series engine mount (#210280) to MTK frame as shown. Make sure that your mount is for a Honda DC chassis. Step 4: Attach MTK engine mounting bracket to
Inhaltszusammenfassung zur Seite Nr. 11
Step 5: Lower engine into subframe and attach it with the hardware provided. Step 6: Connect rear engine stabilizer to transmission as it is aligned on frame. Step 7: Connect and tighten front engine stabilizer bar as it is aligned on frame. 11
Inhaltszusammenfassung zur Seite Nr. 12
Axles: Assembly and Installation Parts needed for Assembly: *Chromoly Axle Shafts, Complete Inner Honda CV Joint Assemblies, and Complete Outer Mini CV Joint Assemblies. (See Photo Below) Step 1: Assemble Small end of axle shaft with the Mini cv joint assembly as done on a stock Mini but replace ball bearing gear with supplied gear. 12
Inhaltszusammenfassung zur Seite Nr. 13
Honda Axle End Assembly: Assemble large splinned side of axle with the Honda cv joint assembly. (See following four Photos) 13
Inhaltszusammenfassung zur Seite Nr. 14
Axle Installation: Simply slide one of the axles into the transmission and the other into the engine mid-shaft until the axles lock into place. Swivel Hubs and Brakes: Install the Swivel Hubs and Brakes as done on stock Mini. Replace Mini steering arm with the *Extended Steering Arm. Route all brake lines along the contour of the MTK Subframe. Coil-Over Shock Installation: Step 1: Attach lower side of shock as shown in photos. 14
Inhaltszusammenfassung zur Seite Nr. 15
Step 2: Attach top shock to upper strut mount. See Photo. Fuel System: Change your fuel pump to one that ranges from 32 to 48 PSI. A return line will be needed on certain models that do not have them. An inline fuel pressure regulator will also be required to set your system at 45psi. Cooling System: The MTK Subframe is designed to use the Honda Civic radiator 1992 – 1998 model but, slightly modified. The bottom port must be cut off and relocated to the bottom side of the radiator.
Inhaltszusammenfassung zur Seite Nr. 16
Torque: 149 ft·lbf (202 N·m) @ 7000 rpm Redline: 8400 rpm o 2001-2006 Honda Integra Type-R (DC5) Displacement: 1998 cc Compression: 11.5:1 Power: 217 hp (220 PS, 162 kW) @ 8000 rpm Torque: 152 ft·lbf (206 N·m) @ 7000 rpm Redline: 8500 rpm o 2002-2006 Honda Accord Euro-R Displacement: 1998 cc Compression: 11.5:1 Power: 217 hp (220 PS, 162 kW) @ 8000 rpm Torque: 152 ft·lbf (206 N·m) @ 7000 rpm Redline: 8500 rpm • K20A2 Found in: o 2002-2004 Acura RSX Type-
Inhaltszusammenfassung zur Seite Nr. 17
- Front Camber Setting = -0.5 to -1 Degree (Less for street driving, more for racing) Check List: For your safety, please check… - That every suspension component - For a firm brake pedal. is fastened tightly. - That the engine is stationary. - That the steering system is - All fluid levels are full. fastened properly and all nuts and - Tires are inflated properly. bolts are secure. - All lug nuts are tight. Test Drive: For your first test drive, go slow and easy to make sure that the
