Inhaltszusammenfassung zur Seite Nr. 1
In-Ground Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
Write Model Number
WARNING!
From Box Here:
READ AND UNDERSTAND
OPERATOR'S MANUAL
BEFORE USING THIS UNIT.
FAILURE TO FOLLOW
OPERATING INSTRUCTIONS
COULD RESULT IN INJURY
OR DAMAGE TO PROPERTY.
Toll-Free Customer Service Number for U.S: 1-800-334-9111
Internet Address: http://www.hydra-rib.com
06/05 ID# M855441
1
Inhaltszusammenfassung zur Seite Nr. 2
IMPORTANT! WRITE MODEL NUMBER FROM BOX ONTO PAGE 1 OF THIS OWNERS MANUAL SAFETY INSTRUCTIONS
FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN WARNING SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY.
Owner must ensure that all players know and F
AILURE
T
O
FOLLO
W
THESE
W
ARNINGS
MA
Y
RESUL
T
follow these rules for safe operation of the system. IN
SERIOUS
INJUR
Y
AND/OR
PR
OPER
TY
D
AMA
GE.
To ensure safety, do not attempt to assemble this system without f
Inhaltszusammenfassung zur Seite Nr. 3
PARTS LIST Item Qty. Part No. Description 1 1 968850 Pole 2 1 998850 Plate, Anchor, Black 3 1 Rim Assembly 4 1 Net 5 4 203017 Nut, Hex, 3/8-16 6 4 203300 Washer, Locking, 3/8 7 2 250001 Bolt, Hex, Tap, 3/8-16 x 4” Long 8 2* 250002 Bolt, Hex, Tap, 3/8-16 x 2” Long 9 1 203457 Label, Logo, Vinyl, 2.3” x 2.7” 10 1 Backboard 11 1 200685 Label, Height Adjustment 12 1 204940 Screw Jack 11 13 2 202666 Name Plate 14 1 808545 Rod, Spacer, 19.8”, Zinc 15 1* 216279 Bolt, Hex, 1/2-13 x 6.5, Black Oxide 16 1
Inhaltszusammenfassung zur Seite Nr. 4
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #23 (1) Item #20 (1) Item #8 (2*) Item #7 (2) Item #29 (4) Item #38 (2) Item #34 (4) 220563
HARDWARE IDENTIFIER (NUTS, WASHERS & SPACERS) 1/4-20 x 1/2
Pan Head #206271 hex head bolt,1/2 x 2 1/2 Item #28 (2*) Item #33 (2*) Item #22 (10) Item #21 (16) Item #24 (9) Item #39 (4) Item #25 (13) Item #5 (4) Item #26 (1) HARDWARE IDENTIFIER (OTHER—NOT ACTUAL SIZE) Item #27 (24) Item #35 (1) Item #37 (1) Item #36 (1) ID# M855441 06/05 4
Inhaltszusammenfassung zur Seite Nr. 5
Ensure ground is level with playing surface, then dig pole hole. 1. 24" (61 cm) 48" (121.9 cm) WARNING! 24" (61 cm) GROUND SURFACE PLAYING SURFACE 48" (121.9 cm) CONTACT UTILITIES XG02.EPS BEFORE DIGGING. 2. Install nut (25) to J-bolt (19) as shown. Repeat procedure for 25 25 remaining three J-bolts (19). 2.75” 2 (7 cm) IMPORTANT! 19 25 Make sure nuts (25) are 2.75” (7 cm) from top of J-bolts Install threaded ends of J-bolts (19) through holes 3. in mounting plate (2) and secure as shown. 19 N
Inhaltszusammenfassung zur Seite Nr. 6
Fill hole with concrete. Tamp down concrete to release air pockets 4. and build drainage hill. DRAINAGE HILL 1" (2.54 cm) PLAYING SURFACE SIDE VIEW Insert J-bolts (19) from mounting plate (2) into cement as shown. Move assembly around to release 5. any air pockets in cement, then rest mounting plate on cement drainage hill. Apply some pressure to HR83005.EPS
level mounting plate on top of dr
Inhaltszusammenfassung zur Seite Nr. 7
Insert bushings (27) into areas 6. shown. 27 10 27 27 27 27 27 27 27 27 27 1 27 17 27 27 18 27 27 27 06/05 ID# M855441 7
Inhaltszusammenfassung zur Seite Nr. 8
Rest top of pole on a piece of scrap wood (not included) and line up holes in pole to holes in 7A. mounting plate (2) as shown. WARNING! PLAYING SURFACE THREE PEOPLE SCRAP WOOD REQUIRED FOR THIS (NOT INCLUDED) PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 2 PLAYING SURFACE Insert bolt (15) through holes in plate and pole and secure with nut (22). 7B. 1 15 22 ID# M855441 06/05 8
Inhaltszusammenfassung zur Seite Nr. 9
8. WARNING! TWO people are required to lift pole into position so that the rod (14) can be installed and secured by the THIRD person. While pole is being supported by TWO THREE PEOPLE capable adults, position rod (14) and lock REQUIRED FOR THIS into place with hitch pin (36) and cotter PROCEDURE. FAILURE pin (37). TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY Slide barrel washer (35) onto other end of AND/OR PROPERTY rod (14) and secure with washer (24) and DAMAGE. nut (25). Tighten
Inhaltszusammenfassung zur Seite Nr. 10
9. While still in forward position, attach both upper and lower yokes (17 & 18) to pole as shown. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 22 21 17 18 21 28 ID# M855441 06/05 10
Inhaltszusammenfassung zur Seite Nr. 11
Attach elevator adjustment (12) to 10. lower yoke (18). WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 18 22 21 12 26 21 20 06/05 ID# M855441 11
Inhaltszusammenfassung zur Seite Nr. 12
Attach elevator adjustment (12) to pole bracket. 11. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. 21 21 23 22 33 33 12 ID# M855441 06/05 12
Inhaltszusammenfassung zur Seite Nr. 13
Attach backboard (10) to upper and lower 12. yokes (18 & 17). Then, hinge board to match up with holes in A. B. First attach board (10) to upper yoke (17), lower yoke (18), FIG. C, and secure with using TWO people to hold the board and hardware as shown in FIG. D. ONE person to attach hardware (FIG. A). Use hardware as shown in FIG. B. WARNING! THREE PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. FIG. C FIG. A FIG. D 1
Inhaltszusammenfassung zur Seite Nr. 14
Before starting, tighten assembly bolt (14) at 6-3/4” from the end of the bolt 13. to the top of the nut (Figure A) Remove rim cover (16), attach rim assembly (3) to backboard (10) and reattach rim cover (16). ** For rim assembly see instructions included with rim. IMPORTANT!: Carefully cut and peel protective film away from board prior to attaching rim. FIGURE A. 5 6 10 Rim Assembly 3 Refer To Instructions 39 Included With Rim 39 Hardware For Rim Assembly. 8 7 ID# M855441 06/05 14 6-3/4”
Inhaltszusammenfassung zur Seite Nr. 15
10 9 87 10 9 87 10 9 87 14. Set-up For Left Side Set-up For Right Side Apply height indicator A. 30 30 labels (32 & 31) to height 7 indicators (30). 10 10 9 7 9 8 7 8 7 31 10 10 32 7 9 8 9 8 7 7 Attach height indicators to lower yoke in area shown by turning screws B. (29) into place with a phillips-head screwdriver. Apply name plate sticker (13) to lower yoke as shown. IMPORTANT! 29 NOTE ORIENTATION 7 OF HEIGHT INDICATORS: 10’ MARK SHOULD FACE AWAY FROM BACKBOARD. 13 10 10 7 9 98 7 8 Attach hei
Inhaltszusammenfassung zur Seite Nr. 16
16. Upright pole (1) by tightening nut (25). WARNING! Using 3/4” wrench, turn nut (25) clockwise to begin standing pole upright. Continue to turn nut (25) THREE PEOPLE REQUIRED FOR THIS PROCEDURE.: TWO PEOPLE ARE REQUIRED TO until pole has come to rest against washers (24) GUIDE AND SUPPORT THE SYSTEM WHILE THE and pole is vertical. THIRD PERSON IS TIGHTENING NUT (25) TO RAISE THE SYSTEM UPRIGHT. Once pole is in its final position, install washers FAILURE TO FOLLOW THIS WARNING COULD (24) and
Inhaltszusammenfassung zur Seite Nr. 17
After pole has been secured to plate (2) loosen nut (25), 17. remove cotter pin (37), and pull out pin (36). This will allow the removal of the assembly bolt (14) which is no longer necessary for the remainder of the assembly and installation of system. WARNING: ONLY AFTER NUTS (25) HAVE BEEN FULLY TIGHTENED: Remove cotter pin (37) and pin (36) to remove assembly bolt (14) from bottom plate (2). 25 24 35 14 37 36 25 06/05 ID# M855441 17
Inhaltszusammenfassung zur Seite Nr. 18
18. Apply height adjust ment label (11). Adjust system by turning crank until desired height is reached per height indicator (30). WARNING! READ AND UNDERSTAND WARNING & HEIGHT ADJUSTMENT LABELS BEFORE USING THIS UNIT. FAILURE TO FOLLOW 30 OPERATING INSTRUCTIONS COULD RESULT IN INJURY OR DAMAGE TO PROPERTY. 10 feet 12 (3.05 m) 11 ID# M855441 06/05 18
Inhaltszusammenfassung zur Seite Nr. 19
LIMITED LIFETIME WARRANTY ® Subject to proper installation and normal use, Hydra-Rib warrants, subject to limitations below, to the original retail ® purchaser all structural components of the Hydra-Rib system to be free of defects in material and workmanship for the duration of ownership by the original retail purchaser. Merchandise must be shipped prepaid with a copy of proof of purchase to our factory for examination to see whether it needs to be repaired or replaced. Any labor costs, travel
