Inhaltszusammenfassung zur Seite Nr. 1
NOTE:
Please read all instructions
carefully before using this
product
®
MARCY DIAMOND ELITE
Table of Contents
Safety Notice
OLYMPIC CAGE
Hardware Identifier
MD-8850
Assembly Instruction
Parts List
Warranty
Ordering Parts
Model
MD-8850
Retain This
Manual for
Reference
07-27-09
OWNER'S
MANUAL
®
IMPEX INC.
14777 DON JULIAN RD., CITY OF INDUSTRY, CA 91746
Tel: (800) 999-8899 Fax: (626) 961-9966
www.impex-fitness.com
info@imp
Inhaltszusammenfassung zur Seite Nr. 2
TABLE OF CONTENTS BEFORE YOU BEGIN...................................................................................... 1 IMPORTANT SAFETY NOTICES..................................................................... 2 CAGE HARDWARE PACK……….....….............................................................4 CAGE ASSEMBLY INSTRUCTIONS.................................................................6 CAGE EXPLODED DIAGRAM................................................................
Inhaltszusammenfassung zur Seite Nr. 3
IMPORTANT SAFETY NOTICE PRECAUTIONS This exercise machine is built for optimum safety. However, certain precautions apply whenever you operate a piece of exercise equipment. Be sure to read the entire manual before you assemble or operate your machine. In particular, note the following safety precautions: 1. Keep children and pets away from the machine at all times. DO NOT leave children unattended in the same room with the machine. 2. Only one person at a
Inhaltszusammenfassung zur Seite Nr. 4
WARNING LABEL PLACEMENT The warning labels shown here have been placed on the Rear Base Frame, Rear Stabilizer, and Upper Frame. If the labels are missing or illegible, please call customer service at 1-800-888-8899 for replacements. Apply the labels in the location shown. 3
Inhaltszusammenfassung zur Seite Nr. 5
CAGE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 4
Inhaltszusammenfassung zur Seite Nr. 6
CAGE HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 5
Inhaltszusammenfassung zur Seite Nr. 7
CAGE ASSEMBLY INSTRUCTION Tools Required for Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches. NOTE: It is strongly recommended that two or more people assemble this machine to avoid possible injury. STEP 1 (See Diagram 1) A.) Attach a Ø 2 ½” Rubber Bumper (#29) and the Weight Storage Post (#14) to Right Stabilizer (#3). Secure it with one M10 x ¾” Allen Bolt (#50) and Ø ¾” Washer (#52). B.) Note: Do not tighten the Nuts and Bolts in following steps until instruct
Inhaltszusammenfassung zur Seite Nr. 8
DIAGRAM 1 7
Inhaltszusammenfassung zur Seite Nr. 9
STEP 2 (See Diagram 2) A.) Insert two Guide Rods (#13) into the holes on the Weight Gliding Base (#7). Secure each Guide Rod with one M10 x ¾” Allen Bolt (#50) and Ø ¾” Washer (#52). B.) Slide two Ø 2 ½” Rubber Bumpers (#29) onto the two Guide Rods to the bottom. Slide the Sliding Frame (#8) onto the two Guide Rods. C.) Attach the Weight Gliding Base to the Rear Base Frame (#4). Secure the side hole with one M10 x 4” Carriage Bolt (#41), one Ø ¾” Washer (#52), and one M10 Aircraft Nut (#
Inhaltszusammenfassung zur Seite Nr. 10
DIAGRAM 2 9
Inhaltszusammenfassung zur Seite Nr. 11
STEP 3 (See Diagram 3) A.) Attach the Sliding Weight Post (#15) to the Sliding Frame (#8). Secure it with two M8 x 1 3/8” Carriage Bolts (#44), two Ø 5/8” Washers (#53), and two M8 Aircraft Nut (#55). Make sure the triangular cable connecting bracket faces up. B.) Attach one 128” Cable (#24) to the front opening on Upper Frame (#6). C.) Attach a Pulley (#39) to the opening. Secure it with M10 x 3 ¾” Allen Bolt (#46), two Ø ¾” Washer (#52), and one M10 Aircraft Nut (#54). D.) Draw the C
Inhaltszusammenfassung zur Seite Nr. 12
DIAGRAM 3 11
Inhaltszusammenfassung zur Seite Nr. 13
STEP 4 (See Diagram 4) A.) Attach the 128” Cable (#24) to the open Pulley bracket on Rear Base Frame (#4). B.) Attach a Pulley to the bracket. Secure it with one M10 x 1 ¾” Allen Bolt (#48), two Ø ¾” Washers (#52), and one M10 Aircraft Nut (#54). C.) Draw the Cable around the Pulley then upward to the Double Floating Pulley Brackets (#25) installed in Step-3. Repeat B to install a Pulley. D.) Draw the Cable around the Pulley then downward to the open hole on the Weight Glide Base (#7).
Inhaltszusammenfassung zur Seite Nr. 14
STEP 5 (See Diagram 5) A.) Slide two Olympic Sleeves (#35) to the Weight Sliding Post (#8). Attach two Spring Clips (#59) to the Sleeves. B.) Attach the Left and Right Bar Catches (#11 & #12), Left and Right Safety Catches (#9 & #10) to selected slot on the two Upright Beams (#1). DIAGRAM 5 13
Inhaltszusammenfassung zur Seite Nr. 15
CAGE EXPLODED DIAGRAM 14
Inhaltszusammenfassung zur Seite Nr. 16
CAGE PART LIST KEY NO. DESCRIPTION Q’ty 1 Upright Beam 2 51 ST3.8 Philips Screw 8 2 Left Stabilizer 1 52 Ø ¾” Washer 45 3 Right Stabilizer 1 53 Ø 5/8” Washer 2 4 Rear Base Frame 1 54 M10 Aircraft Nut 29 5 Top Beam 1 55 M8 Aircraft Nut 2 6 Upper Frame 1 56 Hook 4 7 Weight Glide Base 1 57 10-link Chain 1 8 Sliding Frame 1 58 15-link Chain 1 9 Left Safety Catch 1 59 Spring Clip 2 10 Right Safety Catch 1 #4 Allen Wrench (Tool) 1 11 Left Bar Catch 1 #6 Allen Wre
Inhaltszusammenfassung zur Seite Nr. 17
BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 16
Inhaltszusammenfassung zur Seite Nr. 18
BENCH HARDWARE PACK NOTE: The following parts are not drawn to scale. Please use your own ruler to measure the size. 17
Inhaltszusammenfassung zur Seite Nr. 19
BENCH ASSEMBLY INSTRUCTION STEP 1 (See Diagram 1) A.) Attach the Bench Base Frame (#6) to the Rear Stabilizer (#7). Secure the side-holes with two M10 x 4” Carriage Bolts (#41), two Ø ¾” Washers (#31), and two M10 Aircraft Nuts (#33). Secure the top hole with one M10 x 5/8” Allen Bolt (#36) and one Ø ¾” Washer (#31). B.) Attach the Wheel Set (#25) to the bracket on Rear Stabilizer. Secure it with one M8 x 5 1/8” Allen Bolt (#35), two Ø 5/8” Washers (#30), and one M8 Aircraft Nut (#3
Inhaltszusammenfassung zur Seite Nr. 20
STEP 2 (See Diagram 2) A.) Attach the Main Seat Support (#1) to the Bench Base Frame (#6). Secure it with three M10 x 4” Carriage Bolts (#41), three Ø ¾” Washers (#31), and three M10 Aircraft Nuts (#33). B.) Attach the Front & Rear Seat Bracket (#4 & #5) to Main Seat Support. Secure each Bracket with one M10 x 4” Allen Bolt (#40), two Ø ¾” Washers (#31), and one M10 Aircraft Nut (#33). DIAGRAM 2 19
