Inhaltszusammenfassung zur Seite Nr. 1
SPORTS
H HU UFFY FFY
Portable Basketball System
Owners Manual
Customer Service Center
• N53 W24700 South Corporate Circle • Sussex, WI 53089 • U.S.A.
REQUIRED TOOLS AND MATERIALS:
WARNING!
• Two People
• Wood Board (Scrap)
READ AND UNDERSTAND
• Tape Measure
OPERATOR'S MANUAL
• Step Ladder 8 ft. (2.4 m)
BEFORE USING THIS UNIT.
• Tape
• Garden Hose or Sand 360 lb. (163 kg)
FAILURE TO FOLLOW
• Hammer
OPERATING INSTRUCTIONS
• Wrenches: (Two) 3/4”, (One) 1/2” (Two) 9/16”or
COULD RESULT IN INJURY
equi
Inhaltszusammenfassung zur Seite Nr. 2
WARNING FAILURE TO FOLLOW THESE WARNINGS MAY RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. Owner must ensure that all players know and follow these rules for safe operation of the system. • DO NOT HANG on the rim or any part of the system including backboard, support braces or net. During play, especially when performing dunk type activities, keep player's face away from the backboard, rim and net. Serious injury could occur if teeth/face come in contact with backboard, rim or net.
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INSTRUCTIONS FAILURE TO FOLLOW THESE SAFETY INSTRUCTIONS MAY RESULT IN SERIOUS INJURY, PROPERTY DAMAGE AND WILL VOID WARRANTY. Owner must ensure that all players know and follow these rules for safe operation of the system. To ensure safety, do not attempt to assemble this system without following the instructions carefully. Proper and complete assembly, use and supervision is essential for proper operation and to reduce the risk of accident or injury. A high probability of serious inju
Inhaltszusammenfassung zur Seite Nr. 4
Get to know the basic parts of your basketball system..... FRONT BACK BACKBOARD RIM ELEVATOR TOP POLE ASSEMBLY BOTTOM POLE MIDDLE POLE STRUTS FRONT COVER BASE WHEEL CARRIAGE ASSEMBLY 4 P/N 21447702 03/04
Inhaltszusammenfassung zur Seite Nr. 5
Item Qty Part No. Description 1 1 900149 Top Pole Section 2 1 904811 Middle Pole Section (with Label) 3 1 903407 Bottom Pole Section 4 1 900223 Wheel Bracket 5 1 206940 Axle 6 2 226403 Wheel 7 2 206938 Pushnut 8 1 206660 Base 9 6 203156 Hex Bolt, 5/16-18 x 1 10 18 203218 Flat Washer, 5/16 11 21* 203100 Hex-Flange Nut, 5/16-18 12 1 201581 Pole Bracket 13 2 202662 Hex Bolt, 5/16-18 x 4.5 14 2 203099 Locknut, 5/16-18 15 4 203223 Carriage Bolt, 5/16-18 x 1 16 2 906410 Tank Strut 17 1 200516 Bolt Cov
Inhaltszusammenfassung zur Seite Nr. 6
HARDWARE IDENTIFIER (BOLTS & SCREWS) Item #13 (2) Item #9 (6) Item #47 (1) Item #15 (4) Item #29 (4) Item #54 (2) Item #55 (1) Item #19 (1) Item #50 (6) Item #59 (4) Item #22 (2) HARDWARE IDENTIFIER (NUTS, WASHERS & METAL SPACERS) Item #14 (2) Item #11 (15) Item #31 (4) Item #21 (7) Item #30 (2) Item #44 (4) Item #10 (18) Item #43 (2) Item #41 (4) 6 P/N 21447702 03/04
Inhaltszusammenfassung zur Seite Nr. 7
HARDWARE IDENTIFIER (PLASTIC SPACERS & CAPS) Item #46 (4) Item #17 (1) Item #7 (2) Item #20 (8) Item #49 (4) Item #24 (2) HEIGHT ADJUSTMENT TO ADJUST BACKBOARD: 1 3 1. While holding handle, remove pin. 2. Move elevator up or down to desired height. 2 3. Replace pin full length to lock system at desired height. 2 MOVING SYSTEM 1. Adjust basketball backboard height to lowest position. 1 2. While holding pole, rotate basketball system forward until wheels engage with ground. 3. Move basketball sys
Inhaltszusammenfassung zur Seite Nr. 8
BEFORE YOU START! To ensure optimal playability of backboard system, a close tolerance fit between the elevator components and hardware is required. Test fit large bolts into large holes of elevator tubes, backboard brackets and triangle plates. Carefully rock them in a circular motion to ream out any excess paint from holes if necessary. AVANT DE COMMENCER ! Pour garantir l'utilisation optimale du panneau, les composants du système élévateur et la visserie doivent être bien ajustés (serrés). À
Inhaltszusammenfassung zur Seite Nr. 9
SECTION A: ASSEMBLE THE POLES 1. Mark pole sections with tape (not supplied) as shown. 1 Taped Reference Mark 3 2 Taped Reference Mark WARNING LABEL Bounce middle pole (2) into top pole section 2. (1) using a wood scrap as shown until top pole no longer moves toward pole taped reference mark on middle pole. 2 NOTE: Pole sections should have a 3-1/2" (9 cm) minimum overlap. Taped Reference Mark 1 WOOD SCRAP (NOT SUPPLIED) 9 03/04 P/N 21447702
Inhaltszusammenfassung zur Seite Nr. 10
Align top holes of top pole to bottom holes of bottom pole. While maintaining 3. alignment, bounce top and middle pole assembly (1 & 2) onto lower section (3) using a wood scrap as shown until they no longer move toward pole identification mark on bottom pole (3). IMPORTANT!: Holes in top (1) and bottom pole (3) sections MUST align to correctly position elevator system toward playing surface. 1 RODS SHOWN ARE FOR VISUAL REPRESENTATION OF ALIGNMENT AND ARE NOT SUPPLIED WITH THE HARDWARE Taped Ref
Inhaltszusammenfassung zur Seite Nr. 11
SECTION B: ASSEMBLE THE BASE This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) (2) 1/2” AND (2) 9/16" Wrenches Item #13 AND/OR (2) Socket Wrenches and Sockets Item #9 Item #14 Item #15 Item #17 Item #11 1/2” 9/16” AND a Hammer or Mallet Item #10 Item #7 11 03/04 P/N 21447702
Inhaltszusammenfassung zur Seite Nr. 12
Assemble pole bracket (12) Attach pole assembly to base using 2. 1. carriage bolts (15) washers(10) and nuts using bolt (13) and locknut (14) as shown. (11) as shown. Two people are required for this step. 15 10 13 11 14 IMPORTANT!: WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR 12 PROPERTY DAMAGE. IMPORTANT!: THE CUT CORNERS OF THE POLE BRACKET DO NOT OVER NEED TO FACE TOWARD THE BACK OF TIGHTEN THE BASE AS SHOWN. 12 P/N 21
Inhaltszusammenfassung zur Seite Nr. 13
Secure tank struts (16) to pole as shown. 3. Nut should be tightened until flush (even) with locknuts outer edge. Place cap (17) 10 13 17 over exposed end of bolt as shown. 14 10 16 WARNING! TWO PEOPLE REQUIRED FOR THIS PROCEDURE. FAILURE TO FOLLOW THIS WARNING COULD RESULT IN SERIOUS INJURY AND/OR PROPERTY DAMAGE. IMPORTANT!: Rotate non-secured ends of tank struts (16) outward to mounting holes in tank as 4. shown.Secure ends of tank struts (16) to tank as shown. Repeat for opposite side. 9
Inhaltszusammenfassung zur Seite Nr. 14
Insert axle (5) through wheel bracket (4). Secure wheels (6) to axle using 5. pushnuts (7). Carefully tap pushnuts onto axle with hammer or mallet IMPORTANT!: 6 7 4 5 6 7 SIDE OF WHEEL WITH LONGER PLASTIC AXLE NEEDS TO FACE THE WHEEL BRACKET. Install wheel assembly to base (8) using 6. 9 bolts(9), washers(10) and nuts (11) as shown. 10 8 10 11 14 P/N 21447702 03/04
Inhaltszusammenfassung zur Seite Nr. 15
SECTION C: ASSEMBLE THE ELEVATOR & BACKBOARD This is what your system will look like when you’ve finished this section: HARDWARE USED IN THIS SECTION TOOLS REQUIRED FOR THIS SECTION (not actual size) Item #55 (2) 1/2”, (2) 9/16"” AND (2) 3/4” Item #29 Wrenches Item #54 Item #19 Item #21 AND/OR Item #50 (2) Socket Wrenches and Sockets Item #31 Item #24 Item #11 Item #59 Item #44 1/2” 9/16” 3/4” Item #22 Item #43 Item #30 15 03/04 P/N 21447702
Inhaltszusammenfassung zur Seite Nr. 16
Install pole mount bracket (28) and reinforcement bracket (18) with carriage bolts 1. (22) as shown. Tighten flange nuts (11) completely. 22 18 1 22 28 11 11 Attach spacers (24, 43) to pole mount bracket (28) with bolts (29), washers (44), 2. and lock nuts (31) as shown. IMPORTANT! Tighten just until washers (44) stop moving. 28 44 31 44 44 44 24 29 43 43 24 16 P/N 21447702 03/04
Inhaltszusammenfassung zur Seite Nr. 17
Assemble lanyard (26) to locking pin (27) as shown (FIG A). Attach covers (35) onto 3. pole mount bracket (28) with carriage bolt (19) and nut (11) as shown. IMPORTANT!: 35 11 Loop end of pin lanyard (26) over 28 carriage bolt (19) 35 FIG. A as it passes through the pole mount bracket (28) during this assembly. 26 19 19 26 27 27 Apply logo and height indicator labels (23) to 4. adjustment rod (51) as shown. Attach handle parts (52, 53) to adjustment rod with screw (55), carriage bolts (54), and
Inhaltszusammenfassung zur Seite Nr. 18
Insert handle assembly through pole mount assembly as 5. shown. Lock pole assembly in place at the 10’ (3.05 m) mark with pin (27). 27 30 31 30 31 Assemble backboard brackets (45) 29 6. using spacers (30), bolts (29), and nuts (31) as shown. IMPORTANT!: 29 KEEP HARDWARE LOOSE UNTIL AFTER STEP 8 IS COMPLETED. 45 30 45 29 31 Face of Backboard 18 P/N 21447702 03/04
Inhaltszusammenfassung zur Seite Nr. 19
Identify elevator tubes (33 & 34). 7. Toward Toward Board Pole 33 Upper Elevator tube Toward Toward Board Pole 34 Lower Elevator tube Attach lower elevator tubes (34) and counter balance spring (48) to backboard support brackets (45) using spacers (46 & 49), bolt (50), and nut (21) as shown. NOTE: Rim mounting nuts and bolts supplied with rim hardware. NOTE: DO NOT use washers here on spring return style rims. 46 21 45 48 34 49 49 48 50 34 Refer To Instructions Included With Rim 41 Hardware
Inhaltszusammenfassung zur Seite Nr. 20
Attach upper elevator tubes (33) to backboard support brackets (45) using 8. spacers (46 & 49), bolt (50), and nut (21) as shown. IMPORTANT!: TIGHTEN ALL HARDWARE FROM STEP 6 - 8 AFTER THIS ASSEMBLY IS 46 COMPLETED. 21 49 45 33 49 50 33 46 21 49 33 49 50 33 20 P/N 21447702 03/04