Inhaltszusammenfassung zur Seite Nr. 1
™
GDL 30A XM WeA ther DAt A r eceiver i nst ALLAtion i nstructions
To obtain the best possible performance, install the GDL 30A Weather Data Receiver according to the following instructions. If you experience
difficulty during the installation, contact Garmin Product Support or seek the advice of a professional installer.
Product Registration
Help us better support you by completing our online registration today! Connect to our Web site at http://my.garmin.com. Keep the original
sales receipt,
Inhaltszusammenfassung zur Seite Nr. 2
Unit Overview LED status indicator Power/data connector Network port Weather cap Mounting holes Antenna connector Audio connector CautIon: Always wear safety goggles, ear protection, and a dust mask when drilling, cutting, or sanding. When drilling or cutting, always check what is on the opposite side of the surface. Mounting the GDL 30A Mount the GDL 30A in a location that is dry and well ventilated. Avoid mounting the unit where it may become submerged or exposed to extreme temperatures abo
Inhaltszusammenfassung zur Seite Nr. 3
Connecting the GDL 30A to a Chartplotter Connect the GDL 30A to a chartplotter by using the Garmin Marine Network Cable (included). See the installation instructions for your chartplotter for more detailed information on setting up a Garmin Marine Network. Connecting to a GPSMAP 4000/5000 series chartplotter: • A GPSMAP 4000/5000 series chartplotter has three network connectors available. Connect the GDL 30A to any of these connectors. • If you have multiple chartplotters, connect the GDL 30A
Inhaltszusammenfassung zur Seite Nr. 4
1 2. Drill / in. (3 mm) pilot holes at the three marked locations. 8 note: If you are mounting the GA 32 on fiberglass, it is recommended to use a countersink bit to drill a clearance counterbore through the top gelcoat layer (but no deeper). This will help to avoid cracking in the gelcoat layer when the screws are tightened. 3. Use a 1 in. (25 mm) hole saw to cut the cable hole in the center. ➋ ➋ 4. Place the seal pad on the bottom of the surface-mount bracket. Make sure that the screw holes
Inhaltszusammenfassung zur Seite Nr. 5
Under-deck-mounting the GA 32 Antenna The GA 32 antenna can be mounted under a fiberglass surface with the included adhesive pads. The antenna will not acquire XM satellite signals through metal—you can only use the under-deck mount under a fiberglass surface. 1. Determine the location on the fiberglass surface where you want to mount the GA 32 antenna. 2. Place the adhesive pads on the under-deck mounting bracket. There are holes in the under-deck mounting bracket that can be used to secure
Inhaltszusammenfassung zur Seite Nr. 6
Step 4: Contact XM Call XM Satellite Radio to activate your weather radio and audio radio subscriptions at (800) 985-9200. Weather-Related Broadcast Rates Broadcast Rate Feature (minutes) NEXRAD 5 Cloud Tops 15 Storm Cells 1.25 Lightning 5 Wind 12 Pressure 12 Hurricanes 12 Visibility 12 Fronts 12 Sea Surface Temperature 12 Wave Height 12 Wave Period 12 Wave Direction 12 Current Conditions 12 Forecasts 12 Sea Surface Conditions 12 Blink Codes The GDL 30A turns on and off when the chartplotter to
Inhaltszusammenfassung zur Seite Nr. 7
GDL 30A Specifications Physical 3 3 Size: 4 / in. W × 2 in. H × 6 / in. D (121 mm W × 51 mm H × 172 mm D) 4 4 Weight: 1.5 lb. (.680 kg) Case: Fully gasketed, high-impact plastic and aluminum alloy, waterproof to IEC 60529 IPX7 t emp Range: From 5°F to 158°F ( from -15°C to 70°C) Power Source: 10–35 Vdc usage: 18 watts max Fuse: AGC/3AG - 2.0 A Data Output Source: Proprietary Garmin data format. Audio output Level: 300 mV rms into 47 kohm Frequency Response: 10–20,000 Hz, ± 1 dB
Inhaltszusammenfassung zur Seite Nr. 8
© 2008 Garmin Ltd. or its subsidiaries All rights reserved. Except as expressly provided herein, no part of this manual may be reproduced, copied, transmitted, disseminated, downloaded or stored in any storage medium, for any purpose without the express prior written consent of Garmin. Garmin hereby grants permission to download a single copy of this manual onto a hard drive or other electronic storage medium to be viewed and to print one copy of this manual or of any revision hereto, provide