Bedienungsanleitung Bushnell 53-0021

Inhaltszusammenfassung zur Seite Nr. 1

Model: 53-0021
Lit. #: 98-0579/04-05 Instruction Manual

Inhaltszusammenfassung zur Seite Nr. 2

INTRODUCTION The Bushnell® Holosight® XLP is based on advanced holographic technology. The Bushnell® Holosight® XLP enhances target acquisition, improves accuracy, and provides a high level of control within the shooting environment. This user manual describes the features of the Bushnell® Holosight® XLP and provides information on its use and maintenance. Please read the instructions carefully before mounting and using the sight and always practice proper firearm safety. Included: • Asse

Inhaltszusammenfassung zur Seite Nr. 3

FIGURE 1 BATTERIES Two (2) Type AAA alkaline 1.5 V batteries are required to operate the Bushnell® Holosight® XLP. The Bushnell® Holosight® XLP is designed to maintain constant brightness at a particular setting even as the batteries drain through normal use. The reticle brightness will not fade gradually as the batteries drain, but will shut down abruptly. The fi rst indication of the batteries draining is the reticle image blinking when the unit is turned on (see Electronic Features Sectio

Inhaltszusammenfassung zur Seite Nr. 4

polarity of the exposed contact of the battery. Check the polarity of the battery to be installed and insert 2. OFF the battery so that the opposite polarity end goes into the battery compartment. To re-install the battery To turn the sight off press both UP and DOWN push-button switches simultaneously. Verify that cover, reverse the steps taken to remove the cover. DO NOT OVERTIGHTEN THE KNURLED the unit is off by looking through the display window. SCREW. Secure it with finger tigh

Inhaltszusammenfassung zur Seite Nr. 5

To mount the sight to a Weaver-style rail, follow these steps, refer to Figure 3: NOTE: Loosen the retaining screw just enough to mount or remove the sight. It is not necessary to remove 1. Loosen the 7/64” hex retainer screw that secures the clamp. the screw completely, as the lock hardware will not be retained in the sight and could be lost. 2. Place the sight onto the rail such that the unthreaded portion of the cross bolt is fi tted into a groove on the top of the Weaver-style rail. Th

Inhaltszusammenfassung zur Seite Nr. 6

make adjustments before mounting the sight on the fi rearm. Be sure to check that the mount and the BORE SIGHTING AND ZEROING sight remain fully secured after the fi rst 2 to 3 shots. Bore sighting is a good preliminary procedure in achieving proper alignment of your sight to the fi rearm. If the sight is to be mounted to a Weaver-style rail, it is imperative that the base be parallel to the bore. CAUTION-When a sudden increase in resistance in the adjustment screw is felt, the end of the

Inhaltszusammenfassung zur Seite Nr. 7

MAINTENANCE AND CARE WARRANTY / REPAIR 1. The holographic image glass is coated with anti-reflection material. When cleaning the glass surfaces, TWO-YEAR LIMITED WARRANTY Your Bushnell® product is warranted to be free of defects in materials and workmanship for two years after the date of purchase. In first remove any dirt and dust with compressed air or by blowing on the glass surfaces. Fingerprints or the event of a defect under this warranty, we will, at our option, repair or replace t

Inhaltszusammenfassung zur Seite Nr. 8

ENGLISH FCC COMPLIANCE The Bushnell® Holosight® XLP complies with Part 15b of the FCC Rules. Operation is subject to the following conditions: (1) this device may not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. 12 13

Inhaltszusammenfassung zur Seite Nr. 9

©2005 Bushnell Performance Optics www.bushnell.com