Inhaltszusammenfassung zur Seite Nr. 1
www.zephyronline.com
Tilt
ATI-M90ASX
ATI-M90ABX
RANGE HOOD - Installation instructions
Inhaltszusammenfassung zur Seite Nr. 2
www.zephyronline.com HOTTE PER CUISINE - Notice d’utilisation...Pag. 23 CAMPANA EXTRACTORA - Manual de utilización...Pag. 45 CAPPA ASPIRANTE - istruzioni per l’uso...Pag. 67 - 2 -
Inhaltszusammenfassung zur Seite Nr. 3
SAFETY INSTRUCTIONS..................................................................................................pag. 4 LIST OF MATERIALS...........................................................................................................pag. 7 DUCTING CALCULATION SHEETS...............................................................................pag. 8 HOOD SPECIFICATION.....................................................................................................pag. 9 INSTALL
Inhaltszusammenfassung zur Seite Nr. 4
www.zephyronline.com IMPORTANT SAFETY INSTRUCTIONS FOR RESIDENTIAL USE ONLY READ AND SAVE THESE INSTRUCTIONS PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING. IMPORTANT: Save these Instructions for the Local Electrical Inspectors use. INSTALLER: Please leave these Instructions with this unit for the owner. OWNER: Please retain these instructions for future reference. Take care when using cleaning agents or detergents. Suitable for use in household cooking area WARNING - To reduce the
Inhaltszusammenfassung zur Seite Nr. 5
settings. B. Always turn hood ON when cooking at high heat or when fl ambeing foods ( i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ). C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on fan or fi lter. D. Use proper pan size. Always use cookware appropriate for the size of the surface element. E. Keep fan, fi lters and grease laden surface clean. F. Use high range setting on range only when necessary.Heat oil slowly on low to medium settin
Inhaltszusammenfassung zur Seite Nr. 6
www.zephyronline.com through the fl ue (chimney) of fuel burning equipment to prevent back drafting. Follow the heating equipment manufacturer’s guideline and safety standards such as those published by the National Fire Protection Association (NFPA), and the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities. C. When cutting or drilling into wall or ceiling, do not damage electrical wiring and other hidden utilities. D. Ducte
Inhaltszusammenfassung zur Seite Nr. 7
Top Cover Front Panel Electrical Junction Box Control Light Bulbs Decorative Mesh Filters TYPE DESCRIPTION N° M4 1 + 1 A B 1/8" x 1/4" 12 C 1/8" x 2/4" 4 1/4" x 2-3/4" 6 D - 7 - List of Materials
Inhaltszusammenfassung zur Seite Nr. 8
www.zephyronline.com Maximum Duct Length: For satisfactory air movement, the total duct length should not exceed 100 equivalent feet. - 8 - Ducting Calculation Sheet
Inhaltszusammenfassung zur Seite Nr. 9
front of hood side of hood top of hood - 9 - Hood Specifi cations
Inhaltszusammenfassung zur Seite Nr. 10
www.zephyronline.com NOTE! The device in this version (with internal suction motor) is equipped for rear discharge of exhaust air. However, if required, it is possible to have the exhaust air discharged from the top. This can be accomplished by following the steps indicated in the following paragraphs; upon reaching step 7, the motor plate must not be rotated, there- fore skip steps 8 and 9 and proceed from step 10 directly. The following instructions are for installing the internal b
Inhaltszusammenfassung zur Seite Nr. 11
6. Remove the 6” round metal knockout pla- te from the blower plate by using a fl at head screwdriver. See. Fig.4 7. Remove the (10 ) screws securing the blo- wer plate to the blower housing and remo- ve blower plate. See. Fig.5 (Note! If air is discharged from the top, do not rotate the plate; proceed from step 10 in- stead). 8. Remove the rectangular plate and the fi - xing bracket from the motor plate by loo- sening the 6 screws. Fig.6 9. Rotate the motor plate by 90° and fi x the rectang
Inhaltszusammenfassung zur Seite Nr. 12
www.zephyronline.com 13. Secure Green/Yellow ground wire connected to the cable to the provided capacitor to blower plate. (type A) Fig. 11 14. Attach the 6 pin male molex connector from blower wire to the 6 pin female molex connector located inside the blower housing. See Fig.12 15. Install the blower and plate on the inside of the blower housing: carry out the instruc- tions at step 3 in re- verse order then use the screws provided to complete installa- tion.(Tot. 16 type B) Fig.13 1
Inhaltszusammenfassung zur Seite Nr. 13
NOTE! The device in this version (with external motor) is equipped for rear discharge of exhaust air. However, if required, it is possible to have the exhaust air discharged from the top. This can be accomplished by carrying out the steps indicated in the follow- ing paragraphs; upon reaching step 7, the motor plate must be rotated and installed in the opposite direction. The following instructions are for preparing the hood for use with an ex- ternal or in-line blowers models CBE-1
Inhaltszusammenfassung zur Seite Nr. 14
www.zephyronline.com 5. Close the front panel while holding it by its external sides until it shuts. 6. Remove the metal motor plate by striking it with the aid of a slotted screwdriver. Fig. 4 7 . Remove the (10) screws securing the blo- wer plate to the blower housing and re- move blower plate. See Fig.5 8. (if air is discharged from the top, rotate the motor plate by 90° and fi x the rectan- gular plate and the fi xing bracket in the opposite direction.) Install the chosen flange: rec
Inhaltszusammenfassung zur Seite Nr. 15
Note: Carry out the power supplly con- nection in accordance with the national electric code, ANSI/NFPA 70-1999. Note1: A cable lock (not included) may be required by local codes. Please review lo- cal codes for more information. 12. Attach 6 pin male molex connectors to 6 pin female molex connectors inside blo- wer housing. See Fig 11 Note2: Check local codes to determine mi- nimum wire gauge. See manual included with external and in-line blower for instructions on installing the blowe -
Inhaltszusammenfassung zur Seite Nr. 16
www.zephyronline.com WARNING FIRE HAZARD NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceiling, attics or garages. All exhaust must be ducted to the outside, unless using the recirculating op- tion. Use single wall rigid Metal ductwork only. Fasten all connections with sheet metal screws and tape all joints w/ certif ed Silver Tape or Duct Tape. Some Ducting Options - 16 - Installation - Ducting Options
Inhaltszusammenfassung zur Seite Nr. 17
MOUNTING HEIGHTS The range hood must be installed at a minimum height of 22 inches (56 cm) from the cooking surface. If a connecting duct work composed of two parts is used, the upper part must be placed outside the lower part. Do not connect the range hood duct to the same duct used to exhaust hot air or fumes from another appliance. Before pro- ceeding with the assembly instructions remove the decorative mesh fi lters so that the range hood is
esier to handle.
Inhaltszusammenfassung zur Seite Nr. 18
www.zephyronline.com WARNING: In order to facilitate their connection, make sure that the power supply conduits are not obstructed by the hood. 3. When the hood has been adjusted tighten the screws to secure the hood in place. 4. Once the adjustment has been completed, fi x the hood defi nitely using another (2 type D) screws. NOTE: Screws must be fastened into wooden studs so wood blocking may be necessary. If using wall anchors make sure to check your local codes for suita- bility and typ
Inhaltszusammenfassung zur Seite Nr. 19
GENERAL • Carefully read the following important information regarding installation safety and maintenance. Keep this information booklet accessible for further consultations. POWER SUPPLY CONNECTION For connection to the power supply refer to the following: 1. Remove the power supply cover by undoing the (2) screws Fig. 17. 2. Break through the hole on the box. 3. Pass the wires through the hole in the box and fasten the power supply conduit. Fig.18 4. Connect the wires of the hood to tho
Inhaltszusammenfassung zur Seite Nr. 20
www.zephyronline.com MAINTENANCE • It is recommended to operate the appliance prior to cooking. It is recommended to leave the appliance in operation for 5 minutes after cooking is completed in order to completely eliminate cooking vapors and odors. The proper function of the range hood is conditioned by the regularity of maintenance. • The decorative mesh fi lters capture the grease particles suspended in the air and are therefore subject to clogging because of frequent use. In order to p
