Bedienungsanleitung Rangemaster L1 400370

Inhaltszusammenfassung zur Seite Nr. 1

GB Instruction Manual

Inhaltszusammenfassung zur Seite Nr. 2

Inhaltszusammenfassung zur Seite Nr. 3

RECOMMENDATIONS AND SUGGESTIONS INSTALLATION • The manufacturer will not be held liable for any damages resulting from incorrect or improper installation. • The minimum safety distance between the cooker top and the extractor hood is 650 mm. • Check that the mains voltage corresponds to that indicated on the rating plate fi xed to the inside of the hood. • For Class I appliances, check that the domestic power supply guarantees adequate earthing. Connect the extractor to the exhaust fl ue th

Inhaltszusammenfassung zur Seite Nr. 4

CHARACTERISTICS Dimensions   
  
Hood Type 54 72 L 540 720 L1 512 692 Components Ref. Q.ty Product Components
1 1 Hood Body, complete with: Controls, Light, Blower, Filters 9 1 Reducer Flange ø 150-120 mm Ref. Q.ty Installation Components 12c 2 Screws 2,9 x 6,5

Inhaltszusammenfassung zur Seite Nr. 5

INSTALLATION Drilling the Support surface and Fitting the Hood The Hood can be fi tted directly to the underside of the Wall units (min. 650 mm above the cooker top) with snap-on side supports, which are set up for a support panel thickness of between 15 mm and 30 mm. • Cut a fi tted opening in the bottom surface of the wall unit, as shown. • Remove the metal grease fi lters (see par. on Maintenance). • Disconnect the fi lter support by turning the internal handles provided. • Insert the hood u

Inhaltszusammenfassung zur Seite Nr. 6

• Replace the fi lter support • Screw the fi lter support using the 2 screws 12c (2,9 x 6 ,5) pro- vided. • Replace the grease fi lters make sure that the handle is visible on the outside.   Connections DUCTED VERSION AIR EXHAUST SYSTEM When installing the ducted version, connect the hood to the chimney using either a fl exible or rigid pipe ø 150 or 120 mm, the choice of which is left to the installer. • To install a ø 120 mm air exhaust connection,  insert the reducer fl ange 9 on the h

Inhaltszusammenfassung zur Seite Nr. 7

USE Control Panel The hood can be switched on pushing directly onto the requested speed without fi rstly having to select 0/1 button.      KEY LED FUNCTIONS L 0/1 Light Turns lighting on and off. T1 0/1 Motor on First speed. When pressed for about 2 seconds the motor is switched off. T2 Speed on

Inhaltszusammenfassung zur Seite Nr. 8

REMOTE CONTROL (OPTIONAL) The appliance can be controlled using a remote control powered by a 1.5 V carbon-zinc alkaline batteries of the standard LR03-AAA type. • Do not place the remote control near to heat sources. • Used batteries must be disposed of in the proper manner. MAINTENANCE Grease fi lters CLEANING METAL GREASE FILTERS Alarm signal reset • Switch of the lights and extractor motor. • Press button T3 for at least 3 seconds, until the leds start to fl ash. Cleaning the fi lters • Th

Inhaltszusammenfassung zur Seite Nr. 9

Activated charcoal fi lter (Recirculation version) REPLACING THE ACTIVATED CHARCOAL FILTER • The fi lter is not washable and cannot be regene- rated. It must be replaced when led S1 fl ashes or at least every 4 months. The alarm signal will only light up when the extractor motor is switched on. Alarm signal reset • Switch off the lights and extractor motor. • Press button T3 for at least 3 seconds, until the   leds start to fl ash. Replacing the Filter • Remove the grease fi lters. • Remove the