Inhaltszusammenfassung zur Seite Nr. 1
ENGLISH ES L
See page 2 Vea la página 21
I n s t a l l a t i o n G u i d e
aopñ
83005 Sona Bath Ventilator with Light
READ and SAVE THESE INSTRUCTIONS
41952-01 3/13/2006
05-HF-008-Eng_3.13.06.indd 1 3/13/06 12:08:30 PM
Inhaltszusammenfassung zur Seite Nr. 2
W a r n i n g TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING: such as those published by the National Fire Prevention 1. Use this unit only in a manner intended by the manufacturer. Associa tion (NFPA), and the American Society for Heating, If you have questions, contact the manufacturer at the phone Refrigeration and Air-Conditioning Engineers (ASHRAE), and number or address listed in the warranty. the local code authorities. 2. Before installing, servic
Inhaltszusammenfassung zur Seite Nr. 3
95044-01-000 Check all the parts. E If damaged, call 95022-01-000 1-888-830-1326 F for replacements. 75867-01-000 G x5 A 03242-07-133 H 95492-08-000 I B * 74508-03-133 x2 J 3/8” Cable Connector 96644-01-444 C K * 74933-01-000 L x2 D Extra Screws 75882-01-000 M NOTE: Strain relief cable connector * 75184-01-133 must be installed. Not Included. N 96370-01-444 O Included. Tools Needed. (Not supplied.) Estimated assembly time: 30 to 60 minutes Before Installation NOTE: Remove all p
Inhaltszusammenfassung zur Seite Nr. 4
4 3 I F Remove the motor/blower from the housing. Remove packing material. 5 6 Remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. 7 8 G H Remove the wiring cover screw. Remove the wiring cover. 41952-013/13/2006 41952-01 3/13/2006 4 05-HF-008-Eng_3.13.06.indd 4 3/13/06 12:08:35 PM
Inhaltszusammenfassung zur Seite Nr. 5
9 10 F C B Pop out the first wiring access slug. Use second if needed. Insert the strain relief (not included) into the housing and secure with washer. Choose Installation Option For New Construction - attaching to joist go to step A11, page 5 For New Construction - suspended between joists go to step B11, page 8 For Existing Construction - accessible from above go to step C11, page 11 For Existing Construction - accessible only from below go to step D11, page 15 New Construction - attaching t
Inhaltszusammenfassung zur Seite Nr. 6
A13 Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). A14 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Black Light Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. A0 16 A15 F H Connect 4” duct and vent to the outside. Tape joints. Install the wiring cover plate. Make sure all If du
Inhaltszusammenfassung zur Seite Nr. 7
ON OFF 0000 A17 A18 0000 I Connect wiring harness. DO NOT ALLOW THE MOTOR TO Reinstall the motor by inserting the tabs and pushing up HANG FROM THE WIRING HARNESS. into position. Make sure the wires are not pinched between the motor and the housing. A19 A20 J Secure the motor by tightening the 2 screws. Turn on the power source. A21 A22 Go to step E1 on page 17 to attach grille. Test the motor. If the motor does not run, check the plug connection. 41952-01 3/13/2006 41952-013/13/2006
Inhaltszusammenfassung zur Seite Nr. 8
New Construction – suspended between joists B12 B11 F E 5/8 5/8 1/2 1/2 Slide the mounting rails into brackets. Position the correct depth mark at the bottom edge of the joist based on the thickness of your sheetrock. B13 B14 1/8” bit F Mark position of screws by using holes as a template. Drill a hole in the center of each outline. B15 B16 Insert screws, leaving space between the screw Attach the rails onto the screws. head and the joist. Screws are not provided. 41952-01 3/13/2006
Inhaltszusammenfassung zur Seite Nr. 9
B17 B18 Tighten screws. Route wires through the strain relief. For supply connection, use wires suitable for at least 90º C (194º F). Ground B19 Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Black Light Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. B20 B21 G H Connect 4” duct and vent to the outside. Tape joints. Install the wiring cover plate. Ma
Inhaltszusammenfassung zur Seite Nr. 10
ON OFF B22 B23 I I Reinstall the motor by inserting the tabs and pushing up Connect wiring harness. DO NOT ALLOW THE MOTOR TO into position. Make sure the wires are not pinched HANG FROM THE WIRING HARNESS. between the motor and the housing. B24 B25 J Secure the motor by tightening the 2 screws. Turn on the power source. B26 B27 Go to step E1 on page 17 to attach grille. Test the motor. If the motor does not run, check the plug connection. 41952-013/13/2006 41952-01 3/13/2006 10
Inhaltszusammenfassung zur Seite Nr. 11
9” Existing Construction – accessible from above EXISTING FAN NO EXISTING FAN C11 OR Remove an existing fan and check to make sure the Use the motor housing as a template to mark position. opening is large enough to accommodate the new motor housing (9”x 9.75”). C12 F E Cut out an opening for the housing. Slide the mounting rails into brackets. C14 C13 5/8 5/8 1/2 1/2 Position the correct depth mark at the bottom edge of the Mark position of screws by using holes as a template. joist based on
Inhaltszusammenfassung zur Seite Nr. 12
C15 C16 Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. C18 C17 Attach the rails onto the screws. Tighten screws. C19 C20 Connect 4” duct and vent to the outside. Tape joints. Route wires through the strain relief. For supply connection, If ducting does not fit securely, an adapter may use wires suitable for at least 90º C (194º F). need to be purchased. 41952-013/13/2006 41952-01 3/13/2006 12 05
Inhaltszusammenfassung zur Seite Nr. 13
C21 Tighten the strain relief screws. C22 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. C23 C24 G I H Install the wiring cover plate. Make sure all wiring Connect wiring harness. DO NOT ALLOW THE MOTOR TO connections are inside the box or under the HANG FROM THE WIRING HARNESS. wiring
Inhaltszusammenfassung zur Seite Nr. 14
ON OFF C26 C25 J I Reinstall the motor by inserting the tabs and pushing up Secure the motor by tightening the 2 screws. into position. Make sure the wires are not pinched between the motor and the housing. C27 C28 Test the motor. If the motor does not run, Turn on the power source. check the plug connection. C29 Go to step E1 on page 17 to attach grille. 41952-013/13/2006 41952-01 3/13/2006 14 05-HF-008-Eng_3.13.06.indd 14 3/13/06 12:09:02 PM
Inhaltszusammenfassung zur Seite Nr. 15
Existing Construction – accessible only from below EXISTING FAN D11 D12 F Remove an existing fan and check to make sure the open- Move the housing into position above the ceiling ing is large enough to accommodate the new motor hous- ing (9”x 9.75”). D13 D14 Route wires through the strain relief. For supply connection, Attach existing ducting to duct connector. Tape joints. use wires suitable for at least 90º C (194º F). If ducting does not fit securely, an adapter may need to be purchased. D15
Inhaltszusammenfassung zur Seite Nr. 16
D16 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. D18 D17 G I H Install the wiring cover plate. Make sure all wiring Connect wiring harness. DO NOT ALLOW THE MOTOR TO connections are inside the box or under HANG FROM THE WIRING HARNESS. the wiring cover plate. D20 D19 J I Secure the
Inhaltszusammenfassung zur Seite Nr. 17
ON OFF D22 D21 Test the motor. If the motor does not run, check the plug Turn on the power source. connection. D23 Go to step E1 on page 17 to attach grille. Attaching the Grille E1 E2 F K N Remove the thumbscrews. Connect wiring harness. DO NOT ALLOW THE MOTOR TO HANG FROM THE WIRING HARNESS. 41952-013/13/2006 41952-01 3/13/2006 17 05-HF-008-Eng_3.13.06.indd 17 3/13/06 12:09:10 PM
Inhaltszusammenfassung zur Seite Nr. 18
E3 E4 K N Align posts A, B, C and D (stamped into motor housing) with Attach thumbscrews. posts A, B, C and D (stamped into light fixture). Slide light WARNING: To reduce the risk of electrical shock, fixture over posts. all 4 thumbscrews MUST be properly installed. E5 E6 O M Install fluorescent bulb (Included). Align tabs on glass dome assembly with slots on light fixture, and insert tabs into slots. E7 Turn glass dome assembly as shown until it locks into position. 41952-013/13/2006
Inhaltszusammenfassung zur Seite Nr. 19
Trouble Shooting Problem: Fan does not come on. Solution: • Hunter F an Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wiring diagram. Problem: Light does not come on. Solution: • Replace the light bulb with a new bulb. • T urn power on, rep
Inhaltszusammenfassung zur Seite Nr. 20
Warranty Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts and labor performed
