Inhaltszusammenfassung zur Seite Nr. 1
ENGLISH ES L
See page 2 Vea la página 21
I n s t a l l a t i o n G u i d e
oñap
™
90063/90064 Ellipse Bath Ventilator with Light and Night Light
READ and SAVE THESE INSTRUCTIONS
41722-01 3/29/2006
41722_EngS_3.29.03.indd 1 3/29/06 10:54:38 PM
Inhaltszusammenfassung zur Seite Nr. 2
W a r n i n g TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY, OBSERVE THE FOLLOWING: such as those published by the National Fire Prevention 1. Use this unit only in a manner intended by the manufacturer. Association (NFPA), and the American Society for Heating, If you have questions, contact the manufacturer at the phone Refrigeration and Air-Conditioning Engineers (ASHRAE), and number or address listed in the warranty. the local code authorities. 2. Before installing, servicing, or c
Inhaltszusammenfassung zur Seite Nr. 3
Check all the parts. 95044-01-000 D If damaged, call 1-888-830-1326 95022-01-000 E for replacements. 75190-01-000 F x5 A 03242-07-133 G 95492-01-000 H B * 74508-03-133 3/8” Cable Connector x2 I C 95510-01-000 * J 75184-01-133 K x2 I Extra Screws 95366-01/02-000 NOTE: Strain relief cable connector L * must be installed. Not Included. Included. Tools Needed. (Not supplied) Estimated assembly time: 30 to 60 minutes Before Installation NOTE: Remove all packing materials before instal
Inhaltszusammenfassung zur Seite Nr. 4
4 3 H E Remove the motor/blower from the housing. Remove packing material. 5 6 Remove the pre-loaded screw tip covers. Back out the pre-loaded screw tips until flush with the side of the housing. 7 8 F G Remove the wiring cover screw. Remove the wiring cover. 4 41722-013/29/2006 41722-01 3/29/2006 41722_EngS_3.29.03.indd 4 3/29/06 10:54:44 PM
Inhaltszusammenfassung zur Seite Nr. 5
10 9 E C B Pop out the first wiring access slug. Use second if needed. Insert the strain relief into the housing and secure with the washer. Choose Installation Option For New Construction - attaching to joist go to step A11, page 5 For New Construction - suspended between joists go to step B11, page 8 For Existing Construction - accessible from above go to step C11, page 11 For Existing Construction - accessible only from below go to step D11, page15 New Construction – attaching to joist A11
Inhaltszusammenfassung zur Seite Nr. 6
A13 Pull wires through the strain relief. A14 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. A15 A16 F G • F Install the wiring cover plate. Make sure all Tighten the wiring cover plate screw. wiring connections are inside the box or under the wiring cover plate. 6 41722-013/29/2006
Inhaltszusammenfassung zur Seite Nr. 7
ON OFF A18 A17 0 H Connect 4” duct and vent to the outside. Tape joints. Connect wiring from the motor to the wiring cover plate. If ducting does not fit securely, an adapter may need to be purchased. A19 A20 H I Reinstall the motor by inserting the tabs and pushing up Secure the motor by tightening the 2 screws. into position. Make sure the wires are not pinched between the motor and the housing. A21 A22 Test the motor. If the motor does not run, check the plug Turn on the power source. con
Inhaltszusammenfassung zur Seite Nr. 8
A23 Go to step E1 on page 18 to attach grille. New Construction – suspended between joists B12 B11 E D 5/8 5/8 1/2 1/2 Position the correct depth mark at the bottom edge of Slide the mounting rails into brackets. the joist based on the thickness of your sheetrock. B13 B14 1/8" Bit E Mark position of screws by using holes as a template. Drill a hole in the center of each outline. 8 41722-01 3/29/2006 41722-01 3/29/2006 41722_EngS_3.29.03.indd 8 3/29/06 10:54:53 PM
Inhaltszusammenfassung zur Seite Nr. 9
B15 B16 Insert screws, leaving space between the screw Attach the rails onto the screws. head and the joist. Screws are not provided. B18 B17 Pull wires through the strain relief. Tighten screws. B19 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Black Light Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. 41722-013/29/2006 41722-01 3
Inhaltszusammenfassung zur Seite Nr. 10
B20 B21 F G • F Install the wiring cover plate. Make sure all Tighten the wiring cover plate screw. wiring connections are inside the box or under the wiring cover plate. B23 B22 H Connect 4” duct and vent to the outside. Tape joints. Connect wiring from the motor to the wiring cover plate. If ducting does not fit securely, an adapter may need to be purchased. B24 B25 H I Reinstall the motor by inserting the tabs and pushing up Secure the motor by tightening the 2 screws. into position. Make
Inhaltszusammenfassung zur Seite Nr. 11
ON OFF B27 B26 Turn on the power source. Test the motor. If the motor does not run, check the plug connection. B28 Go to step E1 on page 18 to attach grille. Existing Construction – accessible from above NO EXISTING FAN EXISTING FAN C11 OR Remove an existing fan and check to make sure the Use the motor housing as a template to mark position. opening is large enough to accommodate the new motor housing (9”x 9.75”). 41722-01 3/29/2006 41722-01 3/29/2006 11 41722_EngS_3.29.03.indd 11 3
Inhaltszusammenfassung zur Seite Nr. 12
9” C12 E D Cut out an opening for the housing. Slide the mounting rails into brackets. C13 C14 5/8 5/8 1/2 1/2 Position the correct depth mark at the bottom edge of the Mark position of screws by using holes as a template. joist based on the thickness of your sheetrock. C15 C16 1/8" Bit Drill a hole in the center of each outline. Insert screws, leaving space between the screw head and the joist. Screws are not provided. 41722-01 3/29/2006 41722-01 3/29/2006 12 41722_EngS_3.29.03.in
Inhaltszusammenfassung zur Seite Nr. 13
C17 C18 Attach the rails onto the screws. Tighten screws. C20 C19 Connect 4” duct and vent to the outside. Tape joints. Pull wires through the strain relief. If ducting does not fit securely, an adapter may need to be purchased. C21 Tighten the strain relief screws. 41722-01 3/29/2006 41722-01 3/29/2006 13 41722_EngS_3.29.03.indd 13 3/29/06 10:55:07 PM
Inhaltszusammenfassung zur Seite Nr. 14
C22 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. C23 C24 G • F Install the wiring cover plate. Make sure all Tighten the wiring cover plate screw. wiring connections are inside the box or under the wiring cover plate. C25 C26 H H Connect wiring from the motor to the wiring cover pla
Inhaltszusammenfassung zur Seite Nr. 15
ON OFF C27 C28 I Secure the motor by tightening the 2 screws. Turn on the power source. C29 C30 Go to step E1 on page 18 to attach grille. Test the motor. If the motor does not run, check the plug connection. Existing Construction – accessible only from below EXISTING FAN D11 D12 E Remove an existing fan and check to make sure the open- Move the housing into position above the ceiling ing is large enough to accommodate the new motor hous- ing (9”x 9.75”). 41722-013/29/2006 41722-01
Inhaltszusammenfassung zur Seite Nr. 16
D13 D14 Attach existing ducting to duct connector. Tape joints. Pull wires through strain relief. If ducting does not fit securely, an adapter may need to be purchased. D15 E Screw pre-loaded screws into joist or framing. D16 Ground Black Green 2 Pin Bare Copper White A Black Main Switch 1 (AC In) Fan Motor White White Night Light Red Night Light 3 Pin Light Black Light Red Switch 1 (AC In) *Option Black Switch 2 (AC In) *Option Fan & Main Light Together Connect wires as shown. 41722-013/29
Inhaltszusammenfassung zur Seite Nr. 17
D18 D17 G • F Install the wiring cover plate. Make sure all Tighten the wiring cover plate screw. wiring connections are inside the box or under the wiring cover plate. D20 D19 H H Connect wiring from the motor to the wiring cover plate. Reinstall the motor by inserting the tabs and pushing up into position. Make sure the wires are not pinched between the motor and the housing. D21 D22 I Secure the motor by tightening the 2 screws. Turn on the power source. 41722-013/29/2006 41722-0
Inhaltszusammenfassung zur Seite Nr. 18
ON OFF D23 D24 Go to step E1 on page 18 to attach grille. Test the motor. If the motor does not run, check the plug connection. Attaching the Grille E1 E2 H K L Remove the thumbscrews. Remove glass. E3 E4 H J K Connect wiring harness. Slide light mount over posts and attach thumbscrews. WARNING: To reduce the risk of electrical shock, all 4 thumbscrews MUST be properly installed. 18 41722-01 3/29/2006 41722-01 3/29/2006 41722_EngS_3.29.03.indd 18 3/29/06 10:55:23 PM
Inhaltszusammenfassung zur Seite Nr. 19
E5 E6 J L Align glass and push up. Install 2 Max 60 Watt A-15 bulbs (Not Included) and 1 Max 7 Watt C-7 bulb (Not Included). Trouble Shooting Problem: Fan does not come on. Solution: • Hunter Fan Bath Ventilators are extremely quiet. To confirm that the fan is running, place your hand near the vents to feel the air movement. • Turn power on, replace fuse, or reset breaker. • Check all plug connections to be sure they are secure. • Check the wiring to make sure it matches the wirin
Inhaltszusammenfassung zur Seite Nr. 20
Warranty Hunter Fan Company Bath Exhaust Fan LIMITED WARRANTY Hunter Fan Company makes the following limited warranty to the original user or consumer purchaser of this Hunter bath exhaust fan: If any part of your Hunter bath exhaust fan (except for glass fixtures and light bulbs) fails at any time within one year after the date of sale to you due to a defect in material or workmanship, we will repair or, at our option, replace the defective part free of charge for parts and labor performed
