Bedienungsanleitung Hunter Fan Ceiling Fans

Inhaltszusammenfassung zur Seite Nr. 1

1 1 1
1 1
© 2003 Hunter Fan Company 41847-01 04/21/2003

Inhaltszusammenfassung zur Seite Nr. 2

2 2 2 2 2 If you need help installing the fan, your Hunter fan dealer can di- ® rect you to a licensed installer or electrician. gathering the tools Your new Hunter ceiling fan is an addition to your home or office ® You will need the following tools for installing the fan: that will provide comfort and performance for many years. This • Electric drill with 9/64" bit installation and operation manual gives you complete instructions • Standard screwdriver for installing and operating your fan. •

Inhaltszusammenfassung zur Seite Nr. 3

Inhaltszusammenfassung zur Seite Nr. 4

4 4 4 4 4 cutting the ceiling hole preparing the wiring 1. Locate the site for the hole directly below the joist or support C C C C CA A A A AU U U U UT T T T TI I I I IO O O O ON: A N: A N: A N: A N: All w ll w ll w ll w ll wir ir ir ir irin in in in ing mu g mu g mu g mu g mus s s s st b t b t b t b t be in a e in a e in a e in a e in ac c c c cc c c c co o o o or r r r rd d d d da a a a an n n n nc c c c ce w e w e w e w e wi iii it t t t th n h n h n h n h na- a- a- a- a- brace that wil

Inhaltszusammenfassung zur Seite Nr. 5

5 5 5 5 5 4. Align the slotted holes (refer to Figure 10) in the ceiling plate with the pilot holes in the wood support structure. Note: The Hanger Ball/ isolation pads should be flush against the ceiling. Downrod Assembly For Angled Ceilings: Be sure to orient the ceiling plate so that the arrows on the ceiling plate are pointing towards the ceiling Canopy peak. Refer to Figure 10. Canopy Trim Ring Slots Set Screw F F F F Fi iii ig g g g gur ur ur ur ure 12 - A e 12 - A e 12 - A e 12 - A e 1

Inhaltszusammenfassung zur Seite Nr. 6

Inhaltszusammenfassung zur Seite Nr. 7

Inhaltszusammenfassung zur Seite Nr. 8

8 8 8 8 8 Housing Switch Housing Assembly Blade Iron Mounting Plate Screw Upper Plug Connector Upper Switch Housing F F Fiiig g gur ur ure 26 - A e 26 - A e 26 - At t tt t ta a ac c ch h hin in ing t g t g th h he up e up e upp p pe e er s r s r sw w wiiit t tc c ch h h h h ho o ou u usin sin sing t g t g to t o t o th h he e e F Fiig gur ure 26 - A e 26 - At tt ta ac ch hin ing t g th he up e upp pe er s r sw wiit tc ch h h ho ou usin sing t g to t o th he e m m m m mo o o o oun un un un unt t

Inhaltszusammenfassung zur Seite Nr. 9

Inhaltszusammenfassung zur Seite Nr. 10

10 10 10 10 10 installing without the light fixture operating your ceiling fan Your Hunter fan comes with an integrated light fixture assembly 1. Turn on electrical power to the fan. and an optional switch housing cap and plug button. This feature 2. The fan pull chain controls power to the fan. The pull chain gives you the option of installing the fan with or without the in- has four settings in sequence: High, Medium, Low and Off. cluded light fixture. • Pull the chain slowly to change settin

Inhaltszusammenfassung zur Seite Nr. 11

11 11 11 11 11 cleaning your ceiling fan troubleshooting Problem: Nothing happens; fan does not move. caring for finishes 1. Turn power on, replace fuse, or reset breaker. For cleaning, a soft brush or lint-free cloth should be used to pre- 2. Loosen canopy, check all connections according to the vent scratching the finish. A vacuum cleaner brush nozzle can re- w w wir ir irin in ing t g th he f e fa an n w wir irin ing t g t g th h he f e f e fa a an n n section. move heavier dust. Surface