Bedienungsanleitung Greenheck Fan Smoke Dampers SMD-201

Inhaltszusammenfassung zur Seite Nr. 1

Model SMD-201
Smoke Dampers
Steel 3V Blades
Application
UL 555S Leakage Class I
Model SMD-201 is a leakage rated smoke damper with 3V style
blades. The SMD-201 has been qualified to 2,000 fpm (10.2 m/s) and
Model SMD-201 meets the requirements for smoke
4 in. wg (1 kPa) for operational closure in emergency smoke control
dampers established by:
situations. Model SMD-201 may be installed vertically (with blades run-
National Fire Protection Association
ning horizontally) or horizontally and i

Inhaltszusammenfassung zur Seite Nr. 2

Pressure Drop Data SMD-201 This pressure drop testing was conducted in accordance with AMCA Standard 500-D using the three configurations shown. All 3 3 data has been corrected to represent standard air at a density of .075 lb/ft (1.201 kg/m ). Actual pressure drop found in any HVAC system is a combination of many factors. This pressure drop information along with an analysis of other system influences should be used to estimate actual pressure losses for a damper installed in a given HVAC sy

Inhaltszusammenfassung zur Seite Nr. 3

5D 6D Figure 5.3 AMCA 5.2 Pressure Drop SMD-201 5D 4 (W) (H) = D 3.14 Figure 5.2 Figure 5. 5 12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm) Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop Velocity (fpm) Velocity (fpm) Velocity (fpm) Velocity (fpm) Velocity (fpm) (in. wg) (in. wg) (in. wg) (in. wg) (in. wg) 500 0.04 500 0.02 500 0.01 500 0.01 500 0.0

Inhaltszusammenfassung zur Seite Nr. 4

AMCA 5.3 Pressure Drop SMD-201 5D 6D Figure 5.3 5D 4 (W) (H) = D 3.14 Figure 5.2 Figure 5. 5 12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm) Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop Velocity (fpm) Velocity (fpm) Velocity (fpm) Velocity (fpm) (in. wg) (in. wg) (in. wg) (in. wg) Velocity (fpm) (in. wg) 500 0.02 500 0.01 500 0.01 500 0.01 500 0.

Inhaltszusammenfassung zur Seite Nr. 5

5D 6D 5D 4 (W) (H) D 3.14 AMCA 5.5 Pressure Drop SMD-201 12 in. x 12 in. (305mm x 305mm) 24 in. x 24 in. (610mm x 610mm) 36 in. x 36 in. (914mm x 914mm) 12 in. x 48 in. (305mm x 1219mm) 48 in. x 12 in. (1219mm x 305mm) Pressure Drop Pressure Drop Pressure Drop Pressure Drop Pressure Drop Velocity (fpm) Velocity (fpm) Velocity (fpm) Velocity (fpm) Velocity (fpm) (in. wg) (in. wg) (in. wg) (in. wg) (in. wg) 500 0.04 500 0.06 500 0.03 500 0.03 500 0.03 1000 0.17 1000 0.22 1000 0.14 10

Inhaltszusammenfassung zur Seite Nr. 6

Application Data Damper Sleeve Dimensional Data The drawings below and corresponding table show the position of the SMD-201 damper when mounted in a factory sleeve. The standard mounting locations provide enough space for the mounting of actuators, controls and allow space for installa- tion of retaining angles and duct connections. 1 1 / 2 in. max. The standard location of a damper mounted in a factory sleeve ("A" dimension) is shown below. The damper can be positioned at other location

Inhaltszusammenfassung zur Seite Nr. 7

Damper Sizing Information Dampers larger than maximum single section size are supplied as a factory assembly of two or more sections of equal size. The following figures show maximum damper section size and assembly configurations for multi-section dampers. Double Section Single Section 50 in. 50 in. (1270mm) (1270mm) 50 in. (1270mm) 96 in. (2435mm) 32 in. (813mm) 32 in. (813mm) 64 in. (1626mm) 32 in. (813mm) When a fire/smoke damper is being used in conjunction with round or oval duc