Inhaltszusammenfassung zur Seite Nr. 1
7INCH WIDE TFT LCD MONITOR
Inhaltszusammenfassung zur Seite Nr. 2
Precautions Please read this manual completely and carefully prior to attempting to install your new car video equipment. Install correctly, your new equipment will provide you with year of enjoyable and safe usage. Installation of this equipment in any portion of a vehicle which impairs or distracts the driver is improper and dangerous. We assumes no liability whatsoever for failure to follow the proper installation of this products. 1.Do not operate this equipment while driving-safe driving
Inhaltszusammenfassung zur Seite Nr. 3
Control and layout for the monitor Notice: some functions are work by remote control. 2
Inhaltszusammenfassung zur Seite Nr. 4
Control and layout for the remote control 2. Notice: If the monitor does not have the function, the button would not be work. 3
Inhaltszusammenfassung zur Seite Nr. 5
Function Press FUNCTION button< > on the remote or press manual button< > twice from the monitor to call out the function menu. Fixed Press left < > or right < > button to select your favorite FUNCTION display language PRESS UP < > OR Press left button < >to adjust DOWN < > BUTTON hours & press right button < >to TO SELECT adjust minute Press left or right button < > to select auto on/off Press left or right button < > to call out the calender
Inhaltszusammenfassung zur Seite Nr. 6
Games Press < > to enter the games. Start --Menu Button < > Move --Down Button < > Roll --Up Button < > Exit --Mute Button < > Level --AV Button < > Pause --Menu Button < > Move Left --Volume Button < > Move Right --Volume Button < > Calendar Press FUNCTION < >to call out the function menu, then Press < > to select CALENDAR and press left or right to < > to call out the CALENDAR Adjust increase of year, press < > button Adjust decrease of y
Inhaltszusammenfassung zur Seite Nr. 7
Installation Power Cord (Female) Video 1 input (red) Video 2 input (yellow) Ground (black) DC 12V power input (red) Remote Control replacing batteries PULL OUT PUSH 1) Always use new batteries when replacing the old set. 2)Do not attempt to charge, short-circuit, disassemble, heat or burn used batteries. 3)Battery replacement is necessary when remote control acts sporadically or stops operating. 4)Do not drop, apply shock or step on the remote control 5)Do not spill water on the remote co
Inhaltszusammenfassung zur Seite Nr. 8
Inhaltszusammenfassung zur Seite Nr. 9
Unscrew it and takeaway the back cover before install to headrest housing or sun-visor housing CAUTION: make sure the screw are not long enough to go through the headrest! If you have any doubts about this type of installation, please consult your local mobile electronics retailer. Cutting and make holes in the headrest will cause damage which is expansive to repair. Step of install headrest housing Setup work remove the headrest and set it in an uncluttered work area. Take the appropriate
Inhaltszusammenfassung zur Seite Nr. 10
Measurements Push on the headrest with your fingers to make sure there are no obstructions that would hinder the installation. Use the paper template to mark the area to be cut. Cut the headrest using an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping 1/4 inch in from the other corner. Repeat the procedure for the other two corners. Remove foam & obstructions Carefully peel back the material. Set the adjustable blade to one inch depth and cu
Inhaltszusammenfassung zur Seite Nr. 11
Inhaltszusammenfassung zur Seite Nr. 12
Step of install sun-visor housing Setup work remove the visor and set it in an uncluttered work area. Take the appropriate precautions to ensure that it is not damaged during the installation. Measurements Push on the headrest with your fingers to make sure there are no obstructions that would hinder the installation. Use the paper template to mark the area to be cut. Cut the visor using an adjustable-depth blade, start your cut 1/4 inch inside one corner and cut diagonally across, stopping
Inhaltszusammenfassung zur Seite Nr. 13
Remove foam & obstructions Carefully peel back the material. Set the adjustable blade to one inch depth and cut around the edges of the hole, staying 1/4 inch inside the edge. Pull up one corner of the foam and use the blade to cut underneath. Remove small section at a time, using the pull up and cut method for uniform depth. Use a dremel or other appropriate tool to remove other obstructions. Insert the monitor to measure the fit and make adjustment if necessary Route the cable through the vi
Inhaltszusammenfassung zur Seite Nr. 14
Inhaltszusammenfassung zur Seite Nr. 15
Inhaltszusammenfassung zur Seite Nr. 16
Technical parameters LCD Drive Method: TFT Active Matrix Display Size: 7 Inch Wide Screen (Diagonal) Aspect: 16:9 Display Format: 480 x RGB x 234 Number of Pixels: 1440 x 234 Video System Input: NTSC/PAL Auto-select Back Light: High Brightness Type U Shaped CCFT Power Source: DC12V Current Consumption: 8W Dimension (H x W x D): 113 x 182 x 25 (mm) Stand Style Dimension (H x W x D): 128 x 195 x 24 (mm) Headrest Style Dimension (H x W x D): 127 x 236 x 25 (mm) Sun Visor Style
