Inhaltszusammenfassung zur Seite Nr. 1
MONITOR WITH DVD RECEIVER
KVT-536DVD
KVT-536DVDM
INSTALLATION MANUAL
© B54-4752-00/00 (MW/M2W)
Inhaltszusammenfassung zur Seite Nr. 2
Accessories 1 ..........1 2 ..........1 3 ..........2 4 ..........1 5 ..........4 6 ..........4 | 2 KVT-536DVD/KVT-536DVDM
Inhaltszusammenfassung zur Seite Nr. 3
Installation Procedure • Insulate unconnected wires with vinyl tape or other similar 1. To prevent a short circuit, remove the key from the material. To prevent a short circuit, do not remove the caps ignition and disconnect the - battery. on the ends of the unconnected wires or the terminals. 2. Make the proper input and output wire • Connect the speaker wires correctly to the terminals to connections for each unit. which they correspond. The unit may be damaged or fail to 3. Connect the
Inhaltszusammenfassung zur Seite Nr. 4
Connecting Wires to Terminals Ignition key USB device switch USB connector (commercially available) ACC Ignition wire (Red) Battery wire (Yellow) Car fuse box Car fuse box If you connect the ignition wire (red) and (Main fuse) the battery wire (yellow) to the car chassis (ground), you may cause a short circuit, that Ground wire (Black)- (To car chassis) in turn may start a fire. Always connect those wires to the power source running through the fuse box. Battery FUSE ( 15A ) Connect to t
Inhaltszusammenfassung zur Seite Nr. 5
Cooling fan Antenna Cord FM/AM antenna input Wiring harness (Accessory 1) Audio/Visual input / Rear View Camera Input • Visual input (Yellow) AV IN Wiring harness • Audio left input (White) (Accessory 2) • Audio right input (Red) REAR VIEW CAMERA Audio/Visual Output • Visual output (Yellow) REVERSE • Audio left output (White) AV OUT • Audio right output (Red) ILLUMI Rear/Subwoofer Preout REAR/SUB STEERING WHEEL • Audio left output (White) REMOTE CONT REMOTE INPUT WOOFER • Audio right output (Red
Inhaltszusammenfassung zur Seite Nr. 6
iPod AUDIO IN Optional Accessory Connection iPod (commercially available) KCA-iP301V (Optional Accessory) Audio Input Resistance-free stereo type mini plug (3.5Ф) Audio Output (Black) Visual Input (Yellow) Resistance-free mini plug (3.5Ф) Visual Output (Yellow) USB terminal USB terminal To KCA-BT200 (Optional Accessory) TV Tuner Connection cable (Included in the Navigation System) (Optional Accessory) Navigation System (Optional Accessory) Connection cable (Included in the TV tuner) Navigat
Inhaltszusammenfassung zur Seite Nr. 7
Installation/Removing the Unit Installation Bend the tabs of the mounting sleeve with a screwdriver or similar utensil and attach it in place. Make sure that the unit is installed securely in place. If the unit is unstable, it may malfunction (eg, the sound may skip). | English 7
Inhaltszusammenfassung zur Seite Nr. 8
Installation/Removing the Unit Removing the Hard Rubber Frame Removing the Unit (escutcheon) 1. Remove the hard rubber frame by referring to the removal procedure in the section . remove the two locks on the lower level. 2. Insert the two removal tools 3 deeply into the Lower the frame and pull it forward as shown in slots on each side, as shown. the figure. Removal Tool Escutcheon (Accessory 4) (Accessory 3
Inhaltszusammenfassung zur Seite Nr. 9
Installing in Japanese-made Cars Installation on Toyota, Nissan or Mitsubishi Car using Brackets at Holes shown by "●" or Accessory 5 (M5x6mm) or Accessory 6 (M5x7mm) Car Bracket Accessory 5 (M5x6mm) or Accessory 6 (M5x7mm) Screws (included in audio unit package) Screws (included in audio unit package) Audio unit or others ⁄ • Do not use your own screws. Use only the screws provided. If you use the wrong screws, you could damage the unit. | English 9
Inhaltszusammenfassung zur Seite Nr. 10
Installing in Japanese-made Cars Installation on Toyota Car using Brackets at Holes shown by "●" or When using the bracket shown above, you cannot use screws at two holes of the right and left unit sides. 1. Mount the bracket at each side. Car Bracket Accessory 5 (M5x6mm) Accessory 5 (M5x6mm) Screws (included in audio unit package) Screws (included in audio unit package) 2. Bend each end of case to fix the bracket. Use a flat-blade screwdriver or pliers, and bend each case tab into the ho
Inhaltszusammenfassung zur Seite Nr. 11
Inhaltszusammenfassung zur Seite Nr. 12