Inhaltszusammenfassung zur Seite Nr. 1
50 - 0210F - 002 SERIES 1181291
50 - 0210F - 003 SERIES 1181292
50 - 0210F - 004 SERIES 1181293
3. T -
6. 1/4” hex socket bit
9. Aud
FOR USE IN VEHICLES WITH FACTORY INSTALLED
OVERHEAD CONSOLE ONLY.
- 0019E
Printed in the U.S.A
INSTALLATION INSTRUCTION # 44
July
Inhaltszusammenfassung zur Seite Nr. 2
Description 4 1 ,TEK,Z1 SCREW, # 8 X 2 1/2" PFH ,ZII 3 2 4 3 1 4 1 5 1 6 REAR LIGHT TRIM 1 7 PLYWOOD, 3/8" X 6" X 14" 1 8 SCREW, # 6 X 1/2" 10 9 - 32 X 3/4" 6 10 4 11
Inhaltszusammenfassung zur Seite Nr. 3
1. console together. See Figure 2. See Fig. 2. 3 FIGURE 2 clip on trim ring and separate console from trim ring. Unsnap the wiring connector secured to plastic pins. chisel, carefully remove the head of the (10) ten Using a small through console in some areas. Do not drill deeper than 1/2" or you may drill CAUTION: center of the (10) ten plastic pins which secure he trim ring. Using a 7/64” drill b
Inhaltszusammenfassung zur Seite Nr. 4
3. shoulder. 4 FIGURE 4 FIGURE 3 See Figure 4. plastic pins flush with the Using a razor knife, carefully trim the (10) ten Discard trim ring. See Figure 3.
Inhaltszusammenfassung zur Seite Nr. 5
Caution: Before Cut only where indicated. 5 FIGURE 6 See Figure 6. onentry above headliner. other comp cutting material, check for wiring or OEM pod retainer arms. light opening and the front openings for 5. Cut the headliner material between dome FIGURE 5 assembly if applicable. See Figure 5. the center dome light screw near safe place. Remove the OEM ground wiring and set control head a
Inhaltszusammenfassung zur Seite Nr. 6
the rear pod retainers. Slide bracket to rear of (4) # 8 x 3/4" HWH TEKS screws 6 FIGURE 8 using one of the screws. See Figure 8. 2 ). Secure O.E.M. ground wire (if applicable) ( item 1 pg 7. Secure bracket to sheetmetal frame using four FIGURE 7 recessed area. See Figure 7. vehicle until flange contacts rear edge of previously used to support inner roof openings mounting tabs with th
Inhaltszusammenfassung zur Seite Nr. 7
ure 9. 9. Remove and retain the two ( 2 ) door 7 FIGURE 10 scuff plates on driver’s side. See Fig. 10. FIGURE 9 See Fig and relocate toward center of vehicle. compass, unsnap the wire harness clip 8. If vehicle is equipped with an electronic
Inhaltszusammenfassung zur Seite Nr. 8
10. 11. 12. 13. rotate 90 °. 8 FIGURE 12 (item 8 pg 2 ) through opening and Insert the 6” x 14” piece of plywood vehicle. See Figure 12. that the 4” width is centered in the that is 4” wide x 8” long. Make sure a razor knife, carefully cut an opening toward rear of vehicle. Using opening Measure 7” from rear A/C control FIGURE 11 headliner and lay aside. See Figure 11. from side of vehicl
Inhaltszusammenfassung zur Seite Nr. 9
• - • Down the B - • st source. Ground the black negative lead to the chassis. • 15. Re - - - torque 9 lower seat belt. to manufacturer’s recommended setting. Replace trim pieces previously removed from upper and upper handle, and door trim. Reattach the seat belt bolt and re pillar cover, install the B FIGURE 13 instructions inc
Inhaltszusammenfassung zur Seite Nr. 10
1. 2. Secure the O.E.M. console recess using (10) ten # 6 X 1/2" screws Caution: Do not overtighten 10 FIGURE 15 screws. alternately on each side. See figure 15. beginning with the front center, rear center, then ( item 9 pg 2 ). Start all screws before tightening compartment assembly into the FIGURE 14 area. See figure 14. hinge arms through the slots in the recess pocket th
Inhaltszusammenfassung zur Seite Nr. 11
1. Cons the O.E. orange wires. Do not use O.E. - 32 X 3/4" 4. Secure front of console using two (2 ) # 8 X 1 Caution: Do not two ( 2 ) # 8 x 1 1/4" PWH screws (item 3 pg Caution: Do - 11 Figure 18 installed in step 3. 32 X 3/4" screws previously 6. Tighten 6 roof may occur. not overtighten screws or damage to vehicle le area. See Figure. 17. 2) in dimp 5. Open sunglass holder on O.E. console. Install may occur. overtighten
Inhaltszusammenfassung zur Seite Nr. 12
with video system. your area. Note: Make sure that wires do not get pinched between bosses on video system and (4) 6 - 32 X 3/4" screws (item 10 pg 2) and four Caution: Do not overtighten screws. 12 . rear ed Caution: 13. 14. Attach O.E. wiring to rear A/C control head. Insert 12 transmitter, refer to the
