Inhaltszusammenfassung zur Seite Nr. 1
®
ELECTRONICS CORP.
VOH703 Drop Down TV / Video Monitor
For Customer Service
Visit Our Website At
WWW.audiovox.com
Product Information, Photos,
FAQ’s Owner’s Manuals
Installation Guide
Inhaltszusammenfassung zur Seite Nr. 2
Important Notice It is unlawful in most jurisdictions for a person to drive a motor vehicle which is equipped with a television viewer or screen that is located in the motor vehicle at any point forward of the back of the driver's seat, or that is visible directly or indirectly to the operator of the motor vehicle.
Inhaltszusammenfassung zur Seite Nr. 3
MATERIALS INCLUDED IN THIS PACKAGE: 1) VOH703 Video Monitor with TV Tuner (1 pc) 2) Accessory Harness (P/N 8010730) (1 pc) 3) 12 Pin Power / Signal harness (P/N 112B2821) (1 pc) 4) 2 Pin Power Wire Harness with choke (P/N 112B2824) (1 pc) 5) Hardware Package #4 x 1/4” Screws (5 pcs) #8 x 5/8” Self Drilling Screws (4 pcs) #8 Washers (4 pcs) 6) Remote Control (P/N 136B1612) (1pc) 7) Left Protective Cover for IR sensor (P/N 102B3596) (1pc) 8) Right Protective Cover for Headphone Jacks (P/N 102B359
Inhaltszusammenfassung zur Seite Nr. 4
GENERAL INSTALLATION APPROACH: 1) Decide upon system configuration and options that will be installed (i.e.: what components, VCP, nd Tuner, RF Modulator/external amp, remote headphones, 2 VCP, etc.). 2) Review all manuals to become familiar with electrical requirements and hook ups. 3) Decide upon mounting locations of all components and method of mounting. 4) Prep the vehicle by removing any interior trim necessary to gain access to vehicle's wiring as well as all areas where interconnecting w
Inhaltszusammenfassung zur Seite Nr. 5
VEHICLE PREPARATION: 1) Locate an accessory Power source (+12v when key is in the ACC. and run positions, and 0v when key is off) and a Ground source. Generally, these wires can be found at the ignition switch or fuse- box. 2) The mounting method and location will vary from vehicle to vehicle, so this manual will only focus on the installation of the video monitor and related console accessories. 3) Generally, the best location for the video monitor is where the vehicle's factory dome light is
Inhaltszusammenfassung zur Seite Nr. 6
MINI CONSOLE INSTALLATION: This page only covers special installation considerations for the mini-console installation. If the video monitor is to be installed with a custom full sized overhead console, refer to page 3. If the video monitor is to be installed in a vehicle with the mini console (P/N 102D3595), this console may need to be trimmed to fit the contour of the vehicle headliner. 1) In this installation, the video monitor is mounted directly to the overhead cross-member in the roof usi
Inhaltszusammenfassung zur Seite Nr. 7
MOUNTING THE MINI-CONSOLE Roof Roof Support Headliner 5"x9"x3/4" Plywood Block or Optional VOHBKT (4) #8x1" self drilling screws (not supplied) Mini-Console Video Unit (4) #8 flat washers (not supplied) (4) #8x3/4" self tapping screws (not supplied) -5-
Inhaltszusammenfassung zur Seite Nr. 8
VOH703 Note: cables exiting the pod should be routed as shown. 12 Pin Power signal Harness Item #3 Power Harness Red: +12 VDC Item # 4 Mini-Din Connectors (Accessory Cir.) choke Black: Ground Optional Hard Wired FM Modulator Output 21 RCA-Female 12 VDC Power and Ground Left TV antenna Input Am/Fm (If applicable) LEFT Antenna FM TO WHITE Patch Cord Modulator FACTORY RCA Male to Male RIGHT 1070610 RED RADIO Dash Radio Right *Refer to Instructions with the RF Input Modula
Inhaltszusammenfassung zur Seite Nr. 9
CONNECTING THE DOME LIGHTS The dome lights in the video monitor require three connections to the vehicle's wiring. There are two common types of dome light circuits used, positive or negative switched. Positive systems supply volt- age to the interior lights to turn them on, negative switched systems apply ground to illuminate the bulbs. To determine which system you have you must locate the wires at the dome light. On a positive switched system, with all the doors closed and the lights out,
Inhaltszusammenfassung zur Seite Nr. 10
Negative Switched Dome lighting Red / black - Lamp on To 12 pin Black / red - Lamp common connector Purple / brown - Lamp Auto To constant Factory Dome light circuit To constant Factory Door ajar switch or Body Troubleshooting: SYMPTOM: REMEDY: No power at Video Monitor -Verify +12 VDC on Red wire at 2 pin Power Harness behind video monitor. Verify ground connection with continuity test from known good ground to black wire at 2 pin Power Harness Power but no video or -Verify that the correct so
