Bedienungsanleitung Audiovox 50-0244x-001 SERIES

Inhaltszusammenfassung zur Seite Nr. 1

FOR
50 - - 001 SERIES 1181275
50 - - 018 SERIES 1181276
50 - - 019 SERIES 1181277
CHEVROLET S -
VIDEO SYSTEM














3. T -
5 6. 1/4” hex socket bit






June 3, 1999

- 0025C
Printed in the U.S.A
INSTALLATION INSTRUCTION # 44
8. Audiovox Series 640/650 Video Module 7. Band saw or similar
. Awl or simi

Inhaltszusammenfassung zur Seite Nr. 2

ITEM 6 1 1 4 2 - 4 3 2 4 4 3 1 5 4 1 6 FELT TAPE 3/4" X 8" 2 7 1 8 June 3, 1999 - 0025C Printed in the U.S.A. 2 INSTALLATION INSTRUCTION # 44 JUMPER HARNESS CONSOLE MOUNTING BRACKET WASHER, # 6

Inhaltszusammenfassung zur Seite Nr. 3

1. cover to gain access to (2) two #8 x 3/4" n (1) 2. bracket (item 5 pg 2). Make sure the 8” cut is Caution: Before cu tting indicated. Secure front of bracket to roof brace bracket to roof brace using (4) four #8 x 3/4" screws (item 1 pg 2). Install (2) two #8 x 3/4" O.E.M. screws previously installed.

Inhaltszusammenfassung zur Seite Nr. 4

- secure the cloth covered trim ring to console. 5. Turn console over and open both tape cloth covered trim ring. 5 icated. 6 4 FIGURE See Figure 6. Cut all wires 7” from tape where ind 6. Cut th

Inhaltszusammenfassung zur Seite Nr. 5

the trimmed edge may be visible when See Figure 7. 7 8. pg 2). See Figure 8. 8 5 FIGURE and secure using (2) two pieces of felt tape (item 7 Install the electronic compass in original position FIGURE on either side of dome light. on a padded surface. Trim console along ridge Installer’s option: Turn c

Inhaltszusammenfassung zur Seite Nr. 6

e opening in center of console. See Figure 9. Note: Leave compartment door open to the 90 degree position until console is installed in to installation in vehicle, it will not CAUTION: The edges of O.E.M. console may be sharp and could cut the vinyl necessary to deburr the edge of console 9 Caution: Do light to orange O.E.M. wire. Connect the e over butt connector and

Inhaltszusammenfassung zur Seite Nr. 7

NOTE: Additional assistance in mounting the overhead console in vehicle is 12. nd - C - - plugs, Remote Sensor extension, etc.) to the tion. See Figure 11. Connect per 11 Caution: Do not 14. - 32 X 3/4" 15. Secure the front of console to the inner roof of two #8 x 3/4" screws (item 2 pg 2). See Fig. 12. 17. Tighten (2) two 6 - 32 X 3/4" screws previously

Inhaltszusammenfassung zur Seite Nr. 8

to the video Note: Make sure that wires do not get pinched between bosses on video system and F 13 6 - 32 X 3/4" screws (item 3 pg 2) and (4) four Caution: Do not overtighten screws. 23. Through the open compartment door on Secure using (2) two #8 x 3/4" screws (item 2 pg 2). See Fig. 14. Close compartment door. 14