Inhaltszusammenfassung zur Seite Nr. 1
Model: LCD4WM
3.5” Window Mounted
LCD Monitor
Installation Manual
Features
• 3.5” Inductive Touch Screen LCD Monitor
• Low Profile, Slim Design
• High Resolution TFT LCD
• Built in Speaker
• Two video inputs
• Fully Adjustable
• Auto brightness adjustment
• DC12V – DC24V
Inhaltszusammenfassung zur Seite Nr. 2
Table of Contents Warnings......................................................................................3 Product Description .....................................................................4 Packing List .................................................................................4 LCD Monitor Installation............................................................5 Camera Wiring Diagram..............................................................7 Specifications ....
Inhaltszusammenfassung zur Seite Nr. 3
Warnings The product is intended to assist in safe driving and to allow the driver to have a broader rear view while the vehicle is in reverse. You, as the driver, are solely responsible for the safe operation of your vehicle and the safety of your passengers according to local traffic regulations. Do not use any features of this system to the extent it distracts you from safe driving. Your first priority while driving should always be the safe operation of your vehicle. Audiovox Electr
Inhaltszusammenfassung zur Seite Nr. 4
Product Description This advanced high resolution monitor will show a clear picture from a reversing camera or any other video source. The modern thin design and no button touch screen and built in speaker are all features not found on competitive products. The LCD is perfect for use on your car, truck, or van. This wired Monitor is designed for use with an Advent camera but is compatible with most video sources and other cameras and can be connected using a standard RCA connecto
Inhaltszusammenfassung zur Seite Nr. 5
LCD Monitor Installation 1. Choose a suitable place for the screen in clear view of the driver (recommended positions include next to the Rear Vision Mirror or in the corner of the front window). 2. Examine the vehicle to determine the best way to run the power wires to: accessory power, the reverse lights and to the camera at the rear of the vehicle. 3. Mount the ‘tombstone’ metal lug onto the front Windscreen with Permatex adhesive – follow the Permatex instructions on applic
Inhaltszusammenfassung zur Seite Nr. 6
Wiring the Camera to the Vehicle’s Reverse Lamp 1. Locate the reverse lamp in the tail light assembly. 2. Using the tap connector supplied, perform the following steps: a) Place the un-stripped positive lead from the tail lamp in the run channel, which runs completely through the connector. b) Insert the un-stripped red power wire from the camera completely into the other channel in the connector. c) Make the connection between the wires by crimping down the metal connector with a p
Inhaltszusammenfassung zur Seite Nr. 7
Monitor Wiring Diagram Note: If used with an Advent camera – the power and signal will be provided through a single cable from the monitor. Specifications 1. Voltage: DC9V – DC28V 2. Current: 300mA Maximum 3. Signal System: Switchable 4. Viewing Angle: 160 degrees 5. Minimum Illumination: 0.7 Lux 6. Image Display: Selectable Normal/Reverse Image 7. Adjustable Viewing Angle 7
Inhaltszusammenfassung zur Seite Nr. 8
Troubleshooting Symptom Solution No power to the monitor 1. Check that reverse power is attached to orange wire. 2. Check that accessory power is attached to red wire 3. Check that black is attached to vehicle body (ground) 4. Check fuse and if blown ONLY replace is fuse of same amperage. No image from backup camera 1. Check that camera is when vehicle placed in reverse functioning correctly 2. Check that orange wire is attached to reverse power. 3. Check that backup camera is
Inhaltszusammenfassung zur Seite Nr. 9
7
Inhaltszusammenfassung zur Seite Nr. 10
© 2008 Audiovox Electronics Corp., 150 Marcus Blvd., Hauppauge, N.Y. 11788 8
