Bedienungsanleitung Toyota 95-8211

Inhaltszusammenfassung zur Seite Nr. 1

INSTALLATION INSTRUCTIONS FOR PART 95-8211
APPLICATIONS
Toyota Avalon
2000-2004
95-8211
KIT FEATURES
• Double DIN Radio Provision
• Stacked ISO Mount Units Provision
KIT COMPONENTS
A) Double DIN Trim Plate
A
TOOLS REQUIRED:
Small Flat Blade Screwdriver • Panel Removal Tool
• Phillips Screwdriver • Socket Set
www.metraonline.com
1-800-221-0932
© COPYRIGHT 2004 METRA ELECTRONICS CORPORATION

Inhaltszusammenfassung zur Seite Nr. 2

95-8211 TABLE OF CONTENTS Dash Disassembly - Toyota Avalon 2000-2004 (column shift models) . . . . . . . . . . . . . . . . . . . . . 1 - Toyota Avalon 2000-2004 (console shift models) . . . . . . . . . . . . . . . . . . . . . 2 Kit Assembly - Double DIN Radio Provision ..... ........ ........ ....... ..... ... ... 3 - Stacked ISO Mount Units Provision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Final Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Inhaltszusammenfassung zur Seite Nr. 3

A/C OFF R 95-8211 DASH DISASSEMBLY TOYOTA AVALON 2000-2004 (column shift models) *Note: Refer also to the instructions included with the aftermarket radio. A 1 Disconnect the negative battery- terminal to prevent an accidental short circuit. 2 Unsnap the trim below the cli- mate control to reveal (2) 10 MM bolts and remove. (Figure A) Carefully pull air vents above 3 radio towards rear of car to unsnap. NOTE: There are (3) snaps, (2) are at the bottom sides and (1) is at the top middle of the

Inhaltszusammenfassung zur Seite Nr. 4

R 95-8211 DASH DISASSEMBLY TOYOTA AVALON 2000-2004 (console shift models) *Note: Refer also to the instructions included with the aftermarket radio. 1 Disconnect the negative battery ter- A minal to prevent an accidental short circuit. 2 Open the center console armrest, unsnap cover above cup holder and remove (2) Phillips screws toward the outside of the panel. (Figure A) 3 Lift up and remove shifter trim/ash- tray assembly. (Figure B) B 4 Unsnap black cover from under cli- mate controls and

Inhaltszusammenfassung zur Seite Nr. 5

A/C OFF 95-8211 KIT ASSEMBLY DOUBLE DIN RADIO PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Attach the factory mounting brackets and the Double DIN trim plate to the Double DIN radio using the screws supplied with the radio. (Figure A) Continue to final assembly. A 3

Inhaltszusammenfassung zur Seite Nr. 6

A/C OFF 95-8211 KIT ASSEMBLY STACKED ISO MOUNT UNITS PROVISION *Note: Refer also to the instructions included with the aftermarket radio. 1 Attach the factory mounting brackets and the Double DIN trim plate to the stacked ISO Mount units using the screws supplied with the units. (Figure A) Continue to final assembly. A 4

Inhaltszusammenfassung zur Seite Nr. 7

95-8211 FINAL ASSEMBLY FINAL ASSEMBLY A (A) Strip wire ends back 1/2" B B) Twist ends together C) Solder D) Tape C D 1 Locate the factory wiring harness in the dash. Metra recommends using the proper mating adapter and making connections as shown. (Isolate and individ- ually tape off the ends of any unused wires to prevent electrical short circuit.) 2 Re-connect the negative battery terminal and test the unit for proper operation. 3 Reassemble radio and dash assemblies in reverse order of disas

Inhaltszusammenfassung zur Seite Nr. 8

95-8211 INSTRUCTIONS 1-800-221-0932 www.metraonline.com REV. 01/03/07 © COPYRIGHT 2004 METRA ELECTRONICS CORPORATION INST95-8211