Bedienungsanleitung Metra Electronics CK-612MI

Inhaltszusammenfassung zur Seite Nr. 1

Inhaltszusammenfassung zur Seite Nr. 2

DODGE Stealth 1991-96 / MITSUBISHI 3000GT 1991-98 EAGLE Summit (wg) 1992-96 / MITSUBISHI Expo 1992-95 PLYMOUTH Colt Vista 1992-94 1 2 "E" 1 2 "F" "E" "E" "F" Disconnect the negative battery terminal to "F" prevent an accidental short circuit. Using a Cut and remove mounting tabs "A" and "B" panel removal tool, pry out on the radio trim on the Radio Housing. Cut and remove all Disconnect the negative battery terminal to bezel and remove. Remove (4) screws mounting tabs on Bracket Set

Inhaltszusammenfassung zur Seite Nr. 3

EAGLE Talon / MITSUBISHI Eclipse EAGLE Talon / MITSUBISHI Eclipse 1995-98 PLYMOUTH Laser 1990-94 1 2 1 2 Center console Radio "B" trim bezel "B" Disconnect the negative battery terminal to prevent an accidental short circuit. Slide the front seats forward and remove (1) cover Disconnect the negative battery terminal to cap and (1) Phillips screw from each side of prevent an accidental short circuit. Unclip Cut and remove all mounting tabs on the the center cons

Inhaltszusammenfassung zur Seite Nr. 4

MITSUBISHI Diamante 1994-96 MITSUBISHI Eclipse 2000-01 1 2 1 2 “A” Fig. A “A” “A” Disconnect the negative battery terminal to Disconnect the negative battery terminal to Cut and remove mounting tabs “A” and “B” prevent an accidental short circuit. Remove prevent an accidental short circuit. Remove on the Radio Housing. Locate mounting (2) Phillips screws from each side of the gear (2) Phillips screws under the climate controls. tabs “A” on Bracket Set #3. The mounting shifter console. Remov

Inhaltszusammenfassung zur Seite Nr. 5

MITSUBISHI Galant 1994-98 MITSUBISHI Mirage 1997-00 1 2 1 2 "C" "D" "D" "C" "D" Disconnect the negative battery terminal to Disconnect the negative battery terminal to prevent an accidental short circuit. Pry out prevent an accidental short circuit. Unclip Cut and remove mounting tabs "A" and "B" Cut and remove mounting tabs "A" and "B" the gear shifter trim panel and remove. on the top of the dash trim bezel and remove on the Radio Housing. Locate mounting on the Radio Housing. Cu

Inhaltszusammenfassung zur Seite Nr. 6

MITSUBISHI Montero 1992-96 MITSUBISHI Montero Sport 2000-02 1 2 1 2 "B" "B" "B" "B" "X" Disconnect the negative battery terminal to prevent an accidental short circuit. Remove Cut and remove mounting tabs "A" and "B" Disconnect the negative battery terminal to Cut and remove mounting tabs "A" and "B" (2) screws above the climate controls. prevent an accidental short circuit. Unclip on the Radio Housing. Locate mounting on the Radio Housing. Cut and remove all Unclip the bottom of

Inhaltszusammenfassung zur Seite Nr. 7

5 ALL VEHICLES Fig. A 4 Fig. A Fig. B Fig. B Fig. C Fig. C 2-SHAFT HEAD UNITS: Snap the Shaft Supports into the Radio Housing. Slide the aftermarket head unit into the kit and secure with shaft nuts. (see Fig. A). Fig. D DIN HEAD UNITS: For dash trim bezels with an UNDIVIDED radio opening, slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs down. Slide the aftermarket head unit into the cage until secure. With the side notches DOWN, snap the Facepla

Inhaltszusammenfassung zur Seite Nr. 8

7 Fig. B ¼" Fig. A Fig. C TALON 1995-98, ECLIPSE 1995-98, COLT, SUMMIT, MIRAGE, STEALTH, 3000GT, DIAMANTE, GALANT, MONTERO: No cutting of the dash or dash trim bezel is required. Skip to the Wiring Preparation in step #8. TALON, ECLIPSE, LASER 1990-94: If keeping the factory pocket is desired, cut and remove the inside half of each pocket mount located on the back of the dash trim bezel. (see Fig. A) SUMMIT (wagon), EXPO, COLT VISTA: Cut and remove ¼" from the top edge of the dash cav