Inhaltszusammenfassung zur Seite Nr. 1
CD-PLAYER
KDC-D301
INSTRUCTION MANUAL
COMPACT
DIGITAL AUDIO
B64-1957-00 (EN)
Inhaltszusammenfassung zur Seite Nr. 2
Contents 2Warning 2CAUTION Before use Use of controls or adjustments or Safety Precautions ........................................................................3 performance of procedures other than those Handling Compact Discs...............................................................4 specified herein may result in hazardous Operations radiation exposure. Buttons and Display ......................................................................6 In compliance with Federal Regulations,
Inhaltszusammenfassung zur Seite Nr. 3
Safety precautions Also avoid places with too much dust or the NOTE 2WARNING possibility of water splashing. This equipment has been tested and found to • To prevent deterioration, do not touch the To prevent injury or fire, take the comply with the limits for a Class B digital terminals of the unit or faceplate with your following precautions: device, pursuant to Part 15 of the FCC Rules. fingers. These limits are designed to provide • Insert the unit all the way in until it is fully • Do not s
Inhaltszusammenfassung zur Seite Nr. 4
Safety precautions Handling Compact discs Cleaning the Faceplate Terminals Cleaning the CD Slot Playing a CD that is dirty, scratched or If the terminals on the unit or faceplate get As dust can accumulate in the CD slot, clean warped can cause the sound to skip dirty, wipe them with a dry, soft cloth. it occasionally. Your CDs can get scratched if and the unit to operate incorrectly, you put them in a dusty CD slot. resulting in worsened sound quality. Take the following precautions to Cleaning
Inhaltszusammenfassung zur Seite Nr. 5
Storing CDs Checking New CDs for Burrs Do Not Use Special Shape CDs • Do not store CDs in areas exposed to When playing a new CD for the first time, • Be sure to use round shape CDs only for direct sunlight (such as a car seat or the check that there are not any burrs stuck to this unit and do not use any special shape dashboard) or other hot places. A CD-R or the perimeter of the disc or in the central CDs. Use of special shape CDs may cause CD-RW is more susceptible than a music hole. CDs with
Inhaltszusammenfassung zur Seite Nr. 6
Operations the front, thereby exposing the CD slot. Buttons and Display 2 Holding the CD with the labeled side facing up, insert it in the Release button slot. The CD will start playing. 3 Push back on the right side of the faceplate with your hand until it locks. CD PLAYER KDC-D301 INTEGRATED QUAD MENU 1 BIT D/A CONVERTER DISP NOTE • Select "CD2" when this unit is connected to the CD receiver. DPAC • Selection of the "CD" mode when a CD has not been loaded DIGITAL OPTIMUM 11BAND11BAND resu
Inhaltszusammenfassung zur Seite Nr. 7
Switching Spectrum Analyzer Display Presetting Disc Names You can select the display to enjoy sounds with eyes. NOTE Depending on the centre unit, the number of characters and/or Operation for "N" Setting: Each time you press the DISP button, the spectrum analyzer the number of discs that can be preset may differ, or operations may not be possible. display switches as following table; Operation for "O" Setting: Operation for "N" Setting: This unit permits up to 12 characters to be used for disc
Inhaltszusammenfassung zur Seite Nr. 8
Operations Eject Theft Deterrent Faceplate The faceplate of the unit can be detached and taken with you, A press of the 0 button stops the CD play and ejects the CD. helping to deter theft. 0 Removing Faceplate: Press the release button and drop open the faceplate. In its dropped condition, whilst drawing the faceplate to one side, pull it to the front and remove it. Release button CD PLAYER KDC-D301 INTEGRATED QUAD 1 BIT D/A CONVERTER DISP NOTE DPAC DIGITAL OPTIMUM 11BAND SERVO CONTROL 60 12
Inhaltszusammenfassung zur Seite Nr. 9
Accessories External view External view ......... Number of items ......... Number of items Reattaching Faceplate: Hold the faceplate so that the operation face faces the front 1 4 toward you and press until it .........2 .........1 locks. The faceplate will be set and the unit will be operational. NOTE 2 5 .........1 When there is difficulty in setting .........2 the faceplate, align the depression on the left side of the faceplate 3 6 with the shaft of the unit, then lock. Shaft .........1 ...
Inhaltszusammenfassung zur Seite Nr. 10
Installation Procedure Connections The O-N switch should be set according to the Centre unit in use Centre unit as well as to the connected models. When the centre unit is compatible with the "N"-operation, set the O-N switch to "N". When it is not compatible with the "N"- operation, set the O-N switch to "O" because the operation is not available. The initial setting of the switch is "N". Control input 1. To prevent a short circuit, remove the key from the ignition and disconnect the - battery
Inhaltszusammenfassung zur Seite Nr. 11
Installation (North & South America sales Installation Screwing the Faceplate on the Unit *…North & South America sales area only. area only.) If you want to fasten the faceplate to the main unit so that it does not fall off, insert the provided screw (ø2.6 ´ 12 mm) in the holes as follows. Firewall or metal support Screw (M4X8) 1 Accessory8 Insert one of the HoleÁ Holeª (commercially provided screws into available) holeÁ so that the screw Bottom panel (Accessory4)* is perpendicular to the botto
Inhaltszusammenfassung zur Seite Nr. 12
Installation Removing the hard rubber frame Removing the Unit 1 1 Refer to the section “Removing the hard rubber frame” and Engage the catch pins on the removal tool and remove the two then remove the hard rubber frame. locks on the lower level. Lower the frame and pull it forward as shown in the figure. 2 Remove the Hex-head screw with integral washer (M4´8) on the back panel. 3 Insert the two removal tools deeply into the slots on each side, Catch as shown. Lock Screw (M4X8) Catch facing up (c
Inhaltszusammenfassung zur Seite Nr. 13
Troubleshooting Guide What might seem to be a malfunction in your unit may just be the result of slight misoperation or miswiring. Before calling service, first check the following table for possible problems. PROBLEM POSSIBLE CAUSE SOLUTION The disc control mode cannot No cable has been connected to the disc changer input Connect the control cable to the disc changer input terminal be selected. terminal on the unit. on the centre unit. No CD has been inserted. For centre units brought on to the
Inhaltszusammenfassung zur Seite Nr. 14
Troubleshooting Guide The following messages are displayed on the centre unit when certain problems are occurring in your system. Take the recommended actions. No CD in the unit. E-01 ] Insert the CD. EJECT The faceplate of this unit has been removed. NO PANEL ] Replace it. E-30 The CD is quite dirty. The CD is upside-down. The CD is scratched a lot. E-04 ] Clean the CD and load it correctly. The unit is malfunctioning for some reason. E-99 ] Press the reset button on the centre unit. If the "E-
Inhaltszusammenfassung zur Seite Nr. 15
Specifications Specifications subject to change without notice. CD player section General Laser diode ....................................................GaAlAs (l=780 nm) Operating voltage ..............................14.4 V (11 – 16 V allowable) Digital filter (D/A)......................................8 Times Over Sampling Current consumption............................................................0.8 A D/A Converter ......................................................................1
Inhaltszusammenfassung zur Seite Nr. 16
